On 10/19/2020 4:19 AM, Shankar, Uma wrote:
-----Original Message-----
From: Nautiyal, Ankit K <ankit.k.nautiyal@xxxxxxxxx>
Sent: Thursday, October 15, 2020 4:23 PM
To: intel-gfx@xxxxxxxxxxxxxxxxxxxxx
Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx; Shankar, Uma <uma.shankar@xxxxxxxxx>;
Kulkarni, Vandita <vandita.kulkarni@xxxxxxxxx>; ville.syrjala@xxxxxxxxxxxxxxx;
Sharma, Swati2 <swati2.sharma@xxxxxxxxx>
Subject: [RFC 08/13] drm/i915: Add support for enabling link status and recovery
From: Swati Sharma <swati2.sharma@xxxxxxxxx>
In this patch enabled support for link status and recovery in i915 driver. HDMI
link loss indication to upstream DP source is indicated via IRQ_HPD. This is
followed by reading of HDMI link configuration status
(HDMI_TX_LINK_ACTIVE_STATUS). If the PCON → HDMI 2.1 link status is off;
reinitiate frl link training to recover.
Also, HDMI FRL link error count range for each individual FRL active lane is
indicated by DOWNSTREAM_HDMI_ERROR_STATUS_LN registers.
Signed-off-by: Swati Sharma <swati2.sharma@xxxxxxxxx>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@xxxxxxxxx>
---
drivers/gpu/drm/i915/display/intel_dp.c | 47 +++++++++++++++++++++++--
1 file changed, 44 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c
b/drivers/gpu/drm/i915/display/intel_dp.c
index 668165dd2b1a..e6c4cb844e37 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -5955,6 +5955,29 @@ intel_dp_check_mst_status(struct intel_dp *intel_dp)
return link_ok;
}
+static void
+intel_dp_handle_hdmi_link_status_change(struct intel_dp *intel_dp) {
+bool is_active;
+u8 buf = 0;
+
+is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux);
+if (intel_dp->frl.is_trained && !is_active) {
+if (drm_dp_dpcd_readb(&intel_dp->aux,
DP_PCON_HDMI_LINK_CONFIG_1, &buf) < 0)
+return;
+
+buf &= ~DP_PCON_ENABLE_HDMI_LINK;
+if (drm_dp_dpcd_writeb(&intel_dp->aux,
DP_PCON_HDMI_LINK_CONFIG_1, buf) < 0)
+return;
+
+intel_dp->frl.is_trained = false;
+intel_dp->frl.trained_rate_gbps = 0;
+
+intel_dp_check_frl_training(intel_dp);
+drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux,
&intel_dp->attached_connector->base);
Just printing the error here may not help in recovery. If FRL is failing may be a TMDS fallback should be
attempted. Also error count should be returned instead of just a print.
The function dp_check_frl_training() will restart the FRL link training
if required and fall back to TMDS if FRL does not succeed.
The function for error count should be first and later the frl training
should be checked. Will fix this in next patch version.
The error counts will be different for different lanes, so IMHO, this
information is more for debugging. Not sure, if we can
use this to take any corrective action.
+}
+}
+
static bool
intel_dp_needs_link_retrain(struct intel_dp *intel_dp) { @@ -6320,7 +6343,7
@@ intel_dp_hotplug(struct intel_encoder *encoder,
return state;
}
-static void intel_dp_check_service_irq(struct intel_dp *intel_dp)
+static void intel_dp_check_device_service_irq(struct intel_dp
+*intel_dp)
{
struct drm_i915_private *i915 = dp_to_i915(intel_dp);
u8 val;
@@ -6344,6 +6367,23 @@ static void intel_dp_check_service_irq(struct intel_dp
*intel_dp)
drm_dbg_kms(&i915->drm, "Sink specific irq unhandled\n"); }
+static void intel_dp_check_link_service_irq(struct intel_dp *intel_dp)
+{
+u8 val;
+
+if (intel_dp->dpcd[DP_DPCD_REV] < 0x11)
+return;
+
+if (drm_dp_dpcd_readb(&intel_dp->aux,
+ DP_LINK_SERVICE_IRQ_VECTOR_ESI0, &val) != 1 ||
!val)
An error message would be handy here.
Alright, will be adding appropriate error message here.
+return;
+
+drm_dp_dpcd_writeb(&intel_dp->aux,
DP_LINK_SERVICE_IRQ_VECTOR_ESI0,
+val);
Check for error message here.
As mentioned above, will take care in next version.
Thanks & Regards,
Ankit
+
+if (val & HDMI_LINK_STATUS_CHANGED)
+intel_dp_handle_hdmi_link_status_change(intel_dp);
+}
+
/*
* According to DP spec
* 5.1.2:
@@ -6383,7 +6423,8 @@ intel_dp_short_pulse(struct intel_dp *intel_dp)
return false;
}
-intel_dp_check_service_irq(intel_dp);
+intel_dp_check_device_service_irq(intel_dp);
+intel_dp_check_link_service_irq(intel_dp);
/* Handle CEC interrupts, if any */
drm_dp_cec_irq(&intel_dp->aux);
@@ -6815,7 +6856,7 @@ intel_dp_detect(struct drm_connector *connector,
to_intel_connector(connector)->detect_edid)
status = connector_status_connected;
-intel_dp_check_service_irq(intel_dp);
+intel_dp_check_device_service_irq(intel_dp);
out:
if (status != connector_status_connected && !intel_dp->is_mst)
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
