On Fri, Sep 18, 2020 at 01:39:45PM +0300, Ville Syrjälä wrote:
> On Thu, Sep 17, 2020 at 04:57:09PM -0700, Navare, Manasi wrote:
> > On Fri, Sep 18, 2020 at 12:43:33AM +0300, Ville Syrjala wrote:
> > > From: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
> > >
> > > Refactor the output_format calculation into a helper so that
> > > we can reuse it for mode validation as well.
> > >
> > > Signed-off-by: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
> > > ---
> > > drivers/gpu/drm/i915/display/intel_dp.c | 32 +++++++++++++++----------
> > > 1 file changed, 20 insertions(+), 12 deletions(-)
> > >
> > > diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
> > > index bf1e9cf1c0f3..ad9b8b16fadb 100644
> > > --- a/drivers/gpu/drm/i915/display/intel_dp.c
> > > +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> > > @@ -592,6 +592,22 @@ static u8 intel_dp_dsc_get_slice_count(struct intel_dp *intel_dp,
> > > return 0;
> > > }
> > >
> > > +static enum intel_output_format
> > > +intel_dp_output_format(struct drm_connector *connector,
> > > + const struct drm_display_mode *mode)
> > > +{
> > > + struct intel_dp *intel_dp = intel_attached_dp(to_intel_connector(connector));
> > > + const struct drm_display_info *info = &connector->display_info;
> > > +
> > > + if (!drm_mode_is_420_only(info, mode))
> > > + return INTEL_OUTPUT_FORMAT_RGB;
> > > +
> > > + if (intel_dp->dfp.ycbcr_444_to_420)
> > > + return INTEL_OUTPUT_FORMAT_YCBCR444;
> > > + else
> > > + return INTEL_OUTPUT_FORMAT_YCBCR420;
> > > +}
> > > +
> > > static bool intel_dp_hdisplay_bad(struct drm_i915_private *dev_priv,
> > > int hdisplay)
> > > {
> > > @@ -2430,27 +2446,20 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
> > > }
> > >
> > > static int
> > > -intel_dp_ycbcr420_config(struct intel_dp *intel_dp,
> > > - struct intel_crtc_state *crtc_state,
> > > +intel_dp_ycbcr420_config(struct intel_crtc_state *crtc_state,
> > > const struct drm_connector_state *conn_state)
> > > {
> > > struct drm_connector *connector = conn_state->connector;
> > > - const struct drm_display_info *info = &connector->display_info;
> > > const struct drm_display_mode *adjusted_mode =
> > > &crtc_state->hw.adjusted_mode;
> > >
> > > if (!connector->ycbcr_420_allowed)
> > > return 0;
> > >
> > > - if (!drm_mode_is_420_only(info, adjusted_mode))
> > > - return 0;
> > > + crtc_state->output_format = intel_dp_output_format(connector, adjusted_mode);
> >
> > So by default if its not 420_only then we set it to RGB?
>
> Yes. The code is still a bit messy because we have three places where
> we set this. Probably will try to unify it a bit more, and try to get
> the lspcon stuff looking more like any other protocol converter.
>
> Actually IIRC I noticed that some lspcon chips seem to have some
> of the 1.3 protocol converter registers even though they only
> advertise DPCD 1.2. Not yet sure how to handle that in the
> cleanest way possible...
But if DPCD says only 1.2 then we shouldnt be reading 1.3 specific registers
and support it as 1.2 IMO
Manasi
>
> --
> Ville Syrjälä
> Intel
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
