Hi,
On 7/28/20 8:57 PM, Andy Shevchenko wrote:
On Fri, Jul 17, 2020 at 03:37:43PM +0200, Hans de Goede wrote:
Before this commit a suspend + resume of the LPSS PWM controller
would result in the controller being reset to its defaults of
output-freq = clock/256, duty-cycle=100%, until someone changes
to the output-freq and/or duty-cycle are made.
This problem has been masked so far because the main consumer
(the i915 driver) was always making duty-cycle changes on resume.
With the conversion of the i915 driver to the atomic PWM API the
driver now only disables/enables the PWM on suspend/resume leaving
the output-freq and duty as is, triggering this problem.
The LPSS PWM controller has a mechanism where the ctrl register value
and the actual base-unit and on-time-div values used are latched. When
software sets the SW_UPDATE bit then at the end of the current PWM cycle,
the new values from the ctrl-register will be latched into the actual
registers, and the SW_UPDATE bit will be cleared.
The problem is that before this commit our suspend/resume handling
consisted of simply saving the PWM ctrl register on suspend and
restoring it on resume, without setting the PWM_SW_UPDATE bit.
When the controller has lost its state over a suspend/resume and thus
has been reset to the defaults, just restoring the register is not
enough. We must also set the SW_UPDATE bit to tell the controller to
latch the restored values into the actual registers.
Fixing this problem is not as simple as just or-ing in the value which
is being restored with SW_UPDATE. If the PWM was enabled before we must
write the new settings + PWM_SW_UPDATE before setting PWM_ENABLE.
We must also wait for PWM_SW_UPDATE to become 0 again and depending on the
model we must do this either before or after the setting of PWM_ENABLE.
All the necessary logic for doing this is already present inside
pwm_lpss_apply(), so instead of duplicating this inside the resume
handler, this commit makes the resume handler use pwm_lpss_apply() to
restore the settings when necessary. This fixes the output-freq and
duty-cycle being reset to their defaults on resume.
...
-static int pwm_lpss_apply(struct pwm_chip *chip, struct pwm_device *pwm,
- const struct pwm_state *state)
+static int __pwm_lpss_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state, bool from_resume)
{
struct pwm_lpss_chip *lpwm = to_lpwm(chip);
int ret = 0;
if (state->enabled) {
if (!pwm_is_enabled(pwm)) {
- pm_runtime_get_sync(chip->dev);
+ if (!from_resume)
+ pm_runtime_get_sync(chip->dev);
+
ret = pwm_lpss_prepare_enable(lpwm, pwm, state, true);
- if (ret)
+ if (ret && !from_resume)
pm_runtime_put(chip->dev);
} else {
ret = pwm_lpss_prepare_enable(lpwm, pwm, state, false);
}
} else if (pwm_is_enabled(pwm)) {
pwm_lpss_write(pwm, pwm_lpss_read(pwm) & ~PWM_ENABLE);
- pm_runtime_put(chip->dev);
+
+ if (!from_resume)
+ pm_runtime_put(chip->dev);
}
return ret;
}
Maybe I'm too picky, but I would go even further and split apply to two versions
static int pwm_lpss_apply_on_resume(struct pwm_chip *chip, struct pwm_device *pwm,
const struct pwm_state *state)
{
struct pwm_lpss_chip *lpwm = to_lpwm(chip);
if (state->enabled)
return pwm_lpss_prepare_enable(lpwm, pwm, state, !pwm_is_enabled(pwm));
if (pwm_is_enabled(pwm)) {
pwm_lpss_write(pwm, pwm_lpss_read(pwm) & ~PWM_ENABLE);
return 0;
}
and another one for !from_resume.
It is a bit picky :) But that is actually not a bad idea, although I would write
it like this for more symmetry with the normal (not on_resume) apply version,
while at it I also renamed the function:
/*
* This is a mirror of pwm_lpss_apply() without pm_runtime reference handling
* for restoring the PWM state on resume.
*/
static int pwm_lpss_restore_state(struct pwm_chip *chip, struct pwm_device *pwm,
const struct pwm_state *state)
{
struct pwm_lpss_chip *lpwm = to_lpwm(chip);
int ret = 0;
if (state->enabled)
ret = pwm_lpss_prepare_enable(lpwm, pwm, state, !pwm_is_enabled(pwm));
else if (pwm_is_enabled(pwm))
pwm_lpss_write(pwm, pwm_lpss_read(pwm) & ~PWM_ENABLE);
return ret;
}
Would that work for you?
+static int pwm_lpss_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
+{
+ return __pwm_lpss_apply(chip, pwm, state, false);
+}
...
+ ret = __pwm_lpss_apply(&lpwm->chip, pwm, &saved_state, true);
+ if (ret)
+ dev_err(dev, "Error restoring state on resume\n");
I'm wondering if it's a real error why we do not bail out?
Otherwise dev_warn() ?
It is a real error, but a single PWM chip might have multiple controllers
and bailing out early would mean not even trying to restore the state on
the other controllers. As for propagating the error, AFAIK the pm framework
does not do anything with resume errors other then log an extra error.
Regards,
Hans
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
