Only support runtime changes through the debugfs.
i915.verbose_state_checks remains an exception, and is not exposed via
debugfs.
FIXME: Before this gets applied, IGT *must* be changed to use the
debugfs for modifying the parameters. IGT changes *at least* the
following through module parameter sysfs:
* enable_fbc
* reset
* enable_hangcheck
* enable_psr
* fastboot
* prefault_disable
* load_detect_test
* force_reset_modeset_test
Cc: Juha-Pekka Heikkilä <juha-pekka.heikkila@xxxxxxxxx>
Cc: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@xxxxxxxxx>
Signed-off-by: Jani Nikula <jani.nikula@xxxxxxxxx>
---
drivers/gpu/drm/i915/i915_params.c | 40 +++++++++++++++++++-----------
1 file changed, 25 insertions(+), 15 deletions(-)
diff --git a/drivers/gpu/drm/i915/i915_params.c b/drivers/gpu/drm/i915/i915_params.c
index add00ec1f787..ace44ad7e6df 100644
--- a/drivers/gpu/drm/i915/i915_params.c
+++ b/drivers/gpu/drm/i915/i915_params.c
@@ -40,6 +40,15 @@ struct i915_params i915_modparams __read_mostly = {
#undef MEMBER
};
+/*
+ * Note: As a rule, keep module parameter sysfs permissions read-only
+ * 0400. Runtime changes are only supported through i915 debugfs.
+ *
+ * For any exceptions requiring write access and runtime changes through module
+ * parameter sysfs, prevent debugfs file creation by setting the parameter's
+ * debugfs mode to 0.
+ */
+
i915_param_named(modeset, int, 0400,
"Use kernel modesetting [KMS] (0=disable, "
"1=on, -1=force vga console preference [default])");
@@ -49,7 +58,7 @@ i915_param_named_unsafe(enable_dc, int, 0400,
"(-1=auto [default]; 0=disable; 1=up to DC5; 2=up to DC6; "
"3=up to DC5 with DC3CO; 4=up to DC6 with DC3CO)");
-i915_param_named_unsafe(enable_fbc, int, 0600,
+i915_param_named_unsafe(enable_fbc, int, 0400,
"Enable frame buffer compression for power savings "
"(default: -1 (use per-chip default))");
@@ -57,7 +66,7 @@ i915_param_named_unsafe(lvds_channel_mode, int, 0400,
"Specify LVDS channel mode "
"(0=probe BIOS [default], 1=single-channel, 2=dual-channel)");
-i915_param_named_unsafe(panel_use_ssc, int, 0600,
+i915_param_named_unsafe(panel_use_ssc, int, 0400,
"Use Spread Spectrum Clock with panels [LVDS/eDP] "
"(default: auto from VBT)");
@@ -65,25 +74,25 @@ i915_param_named_unsafe(vbt_sdvo_panel_type, int, 0400,
"Override/Ignore selection of SDVO panel mode in the VBT "
"(-2=ignore, -1=auto [default], index in VBT BIOS table)");
-i915_param_named_unsafe(reset, int, 0600,
+i915_param_named_unsafe(reset, int, 0400,
"Attempt GPU resets (0=disabled, 1=full gpu reset, 2=engine reset [default])");
i915_param_named_unsafe(vbt_firmware, charp, 0400,
"Load VBT from specified file under /lib/firmware");
#if IS_ENABLED(CONFIG_DRM_I915_CAPTURE_ERROR)
-i915_param_named(error_capture, bool, 0600,
+i915_param_named(error_capture, bool, 0400,
"Record the GPU state following a hang. "
"This information in /sys/class/drm/card<N>/error is vital for "
"triaging and debugging hangs.");
#endif
-i915_param_named_unsafe(enable_hangcheck, bool, 0600,
+i915_param_named_unsafe(enable_hangcheck, bool, 0400,
"Periodically check GPU activity for detecting hangs. "
"WARNING: Disabling this can cause system wide hangs. "
"(default: true)");
-i915_param_named_unsafe(enable_psr, int, 0600,
+i915_param_named_unsafe(enable_psr, int, 0400,
"Enable PSR "
"(0=disabled, 1=enabled) "
"Default: -1 (use per-chip default)");
@@ -96,22 +105,22 @@ i915_param_named_unsafe(disable_power_well, int, 0400,
"Disable display power wells when possible "
"(-1=auto [default], 0=power wells always on, 1=power wells disabled when possible)");
-i915_param_named_unsafe(enable_ips, int, 0600, "Enable IPS (default: true)");
+i915_param_named_unsafe(enable_ips, int, 0400, "Enable IPS (default: true)");
-i915_param_named(fastboot, int, 0600,
+i915_param_named(fastboot, int, 0400,
"Try to skip unnecessary mode sets at boot time "
"(0=disabled, 1=enabled) "
"Default: -1 (use per-chip default)");
-i915_param_named_unsafe(load_detect_test, bool, 0600,
+i915_param_named_unsafe(load_detect_test, bool, 0400,
"Force-enable the VGA load detect code for testing (default:false). "
"For developers only.");
-i915_param_named_unsafe(force_reset_modeset_test, bool, 0600,
+i915_param_named_unsafe(force_reset_modeset_test, bool, 0400,
"Force a modeset during gpu reset for testing (default:false). "
"For developers only.");
-i915_param_named_unsafe(invert_brightness, int, 0600,
+i915_param_named_unsafe(invert_brightness, int, 0400,
"Invert backlight brightness "
"(-1 force normal, 0 machine defaults, 1 force inversion), please "
"report PCI device ID, subsystem vendor and subsystem device ID "
@@ -121,10 +130,11 @@ i915_param_named_unsafe(invert_brightness, int, 0600,
i915_param_named(disable_display, bool, 0400,
"Disable display (default: false)");
-i915_param_named(mmio_debug, int, 0600,
+i915_param_named(mmio_debug, int, 0400,
"Enable the MMIO debug code for the first N failures (default: off). "
"This may negatively affect performance.");
+/* Special case writable file */
i915_param_named(verbose_state_checks, bool, 0600,
"Enable verbose logs (ie. WARN_ON()) in case of unexpected hw state conditions.");
@@ -155,7 +165,7 @@ i915_param_named_unsafe(huc_firmware_path, charp, 0400,
i915_param_named_unsafe(dmc_firmware_path, charp, 0400,
"DMC firmware path to use instead of the default one");
-i915_param_named_unsafe(enable_dp_mst, bool, 0600,
+i915_param_named_unsafe(enable_dp_mst, bool, 0400,
"Enable multi-stream transport (MST) for new DisplayPort sinks. (default: true)");
#if IS_ENABLED(CONFIG_DRM_I915_DEBUG)
@@ -163,7 +173,7 @@ i915_param_named_unsafe(inject_probe_failure, uint, 0400,
"Force an error after a number of failure check points (0:disabled (default), N:force failure at the Nth failure check point)");
#endif
-i915_param_named(enable_dpcd_backlight, int, 0600,
+i915_param_named(enable_dpcd_backlight, int, 0400,
"Enable support for DPCD backlight control"
"(-1=use per-VBT LFP backlight type setting [default], 0=disabled, 1=enabled)");
@@ -173,7 +183,7 @@ i915_param_named(enable_gvt, bool, 0400,
#endif
#if IS_ENABLED(CONFIG_DRM_I915_UNSTABLE_FAKE_LMEM)
-i915_param_named_unsafe(fake_lmem_start, ulong, 0600,
+i915_param_named_unsafe(fake_lmem_start, ulong, 0400,
"Fake LMEM start offset (default: 0)");
#endif
--
2.20.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
