Transcoder timing calculation differ for command mode.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@xxxxxxxxx>
---
drivers/gpu/drm/i915/display/icl_dsi.c | 56 +++++++++++++++++---------
1 file changed, 37 insertions(+), 19 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index 8e6c09a1db78..5dd9eebab6b1 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -780,6 +780,7 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
u16 hback_porch;
/* vertical timings */
u16 vtotal, vactive, vsync_start, vsync_end, vsync_shift;
+ int bpp, line_time_us, byte_clk_period_ns;
hactive = adjusted_mode->crtc_hdisplay;
htotal = adjusted_mode->crtc_htotal;
@@ -841,40 +842,57 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
}
/* program TRANS_VTOTAL register */
- for_each_dsi_port(port, intel_dsi->ports) {
- dsi_trans = dsi_port_to_transcoder(port);
- /*
- * FIXME: Programing this by assuming progressive mode, since
- * non-interlaced info from VBT is not saved inside
- * struct drm_display_mode.
- * For interlace mode: program required pixel minus 2
- */
- I915_WRITE(VTOTAL(dsi_trans),
- (vactive - 1) | ((vtotal - 1) << 16));
+ if (intel_dsi->operation_mode == INTEL_DSI_VIDEO_MODE) {
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ /*
+ * FIXME: Programing this by assuming progressive mode,
+ * since non-interlaced info from VBT is not saved
+ * inside struct drm_display_mode.
+ * For interlace mode: program required pixel minus 2
+ */
+ I915_WRITE(VTOTAL(dsi_trans),
+ (vactive - 1) | ((vtotal - 1) << 16));
+ }
+ } else {
+ for_each_dsi_port(port, intel_dsi->ports) {
+ bpp = mipi_dsi_pixel_format_to_bpp(intel_dsi->pixel_format);
+ byte_clk_period_ns = 8 * 1000000 / intel_dsi->pclk;
+ htotal = hactive + 160;
+ line_time_us = (htotal * (bpp / 8) * byte_clk_period_ns) / (1000 * intel_dsi->lane_count);
+ vtotal = vactive + DIV_ROUND_UP(460, line_time_us);
+ I915_WRITE(VTOTAL(dsi_trans),
+ (vactive - 1) | ((vtotal - 1) << 16));
+ }
}
+
if (vsync_end < vsync_start || vsync_end > vtotal)
DRM_ERROR("Invalid vsync_end value\n");
if (vsync_start < vactive)
DRM_ERROR("vsync_start less than vactive\n");
- /* program TRANS_VSYNC register */
- for_each_dsi_port(port, intel_dsi->ports) {
- dsi_trans = dsi_port_to_transcoder(port);
- I915_WRITE(VSYNC(dsi_trans),
- (vsync_start - 1) | ((vsync_end - 1) << 16));
+ /* program TRANS_VSYNC register for video mode only */
+ if (intel_dsi->operation_mode == INTEL_DSI_VIDEO_MODE) {
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ I915_WRITE(VSYNC(dsi_trans),
+ (vsync_start - 1) | ((vsync_end - 1) << 16));
+ }
}
/*
- * FIXME: It has to be programmed only for interlaced
+ * FIXME: It has to be programmed only for video modes and interlaced
* modes. Put the check condition here once interlaced
* info available as described above.
* program TRANS_VSYNCSHIFT register
*/
- for_each_dsi_port(port, intel_dsi->ports) {
- dsi_trans = dsi_port_to_transcoder(port);
- I915_WRITE(VSYNCSHIFT(dsi_trans), vsync_shift);
+ if (intel_dsi->operation_mode == INTEL_DSI_VIDEO_MODE) {
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ I915_WRITE(VSYNCSHIFT(dsi_trans), vsync_shift);
+ }
}
/* program TRANS_VBLANK register, should be same as vtotal programmed */
--
2.21.0.5.gaeb582a
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
