On Tue, 2019-09-24 at 18:58 +0300, Imre Deak wrote:
> On Mon, Sep 23, 2019 at 12:55:11PM -0700, José Roberto de Souza
> wrote:
> > Link training is failling when running link at 2.7GHz and 1.62GHz
> > and
> > following BSpec pll algorithm.
> >
> > Comparing the values calculated and the ones from the reference
> > table
> > it looks like MG_CLKTOP2_CORECLKCTL1_A_DIVRATIO should not always
> > set
> > to 5. For DP ports ICL mg pll algorithm sets it to 10 or 5 based on
> > div2 value, that matches with dkl hardcoded table.
> >
> > So implementing this way as it proved to work in HW and leaving a
> > comment so we know why it do not match BSpec.
> >
> > Issue reported on BSpec 49204.
> >
> > Signed-off-by: José Roberto de Souza <jose.souza@xxxxxxxxx>
> > ---
> > drivers/gpu/drm/i915/display/intel_dpll_mgr.c | 7 ++++++-
> > 1 file changed, 6 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
> > b/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
> > index 496df4095a21..3c881d4cf973 100644
> > --- a/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
> > +++ b/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
> > @@ -2631,7 +2631,12 @@ static bool icl_mg_pll_find_divisors(int
> > clock_khz, bool is_dp, bool use_ssc,
> >
> > if (div2 >= 2) {
> > if (is_dkl) {
> > - a_divratio = 5;
> > + /*
> > + * Note: a_divratio not
> > matching TGL
> > + * BSpec algorithm but matching
> > + * hardcoded values and working
> > on HW
> > + */
> > + a_divratio = 10;
>
> Yes, matches the hardcoded values for CLKTOP2_HSCLKCTL/CORECLKCTL1,
> with
> the exception that the hardcoded value for CLKTOP2_HSCLKCTL 5p4 is
> also
> incorrect wrt. div2 within that (should be 1 but it's 2).
>
> However we don't have any hardcoded values in Bspec for HDMI except
> for
> the 5.94Gbps/div2=1 case. So until otherwise proven, for HDMI/div2>=2
> I
> wouldn't change the value, rather have the same logic as for ICL that
> is
> is_dp ? 10 : 5;
I was trying to avoid touch any HDMI calculation as I can't test it but
it looks sane, so I will keep the if is_dkl, replace to "a_divratio =
is_dp ? 10 : 5;" and add to the comment that this is the supposed value
for HDMI but it is not tested.
>
> > tlinedrv = 1;
> > } else {
> > a_divratio = is_dp ? 10 : 5;
> > --
> > 2.23.0
> >
> > _______________________________________________
> > Intel-gfx mailing list
> > Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
> > https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
