Re: [PATCH 25/39] drm/i915/tgl: Implement TGL DisplayPort training sequence

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, 2019-08-19 at 16:21 +0200, Maarten Lankhorst wrote:
> Op 16-08-2019 om 10:04 schreef Lucas De Marchi:
> > From: José Roberto de Souza <jose.souza@xxxxxxxxx>
> > 
> > On TGL some registers moved from DDI to transcoder and the
> > DisplayPort training sequence has a separate BSpec page.
> > 
> > I started adding 'ifs' to the original intel_ddi_pre_enable_dp()
> > but
> > it was becoming really hard to follow, so a new and cleaner
> > function
> > for TGL was added with comments of all steps. It's similar to ICL,
> > but
> > different enough to deserve a new function
> > 
> > The rest of DisplayPort enable and the whole disable sequences
> > remained the same.
> > 
> > BSpec: 49190
> > Cc: Manasi Navare <manasi.d.navare@xxxxxxxxx>
> > Cc: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
> > Signed-off-by: José Roberto de Souza <jose.souza@xxxxxxxxx>
> > Signed-off-by: Lucas De Marchi <lucas.demarchi@xxxxxxxxx>
> > ---
> >  drivers/gpu/drm/i915/display/intel_ddi.c | 134
> > ++++++++++++++++++++++-
> >  drivers/gpu/drm/i915/display/intel_dp.c  |   8 +-
> >  2 files changed, 134 insertions(+), 8 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c
> > b/drivers/gpu/drm/i915/display/intel_ddi.c
> > index 17d49c77faa0..5d971e9d0459 100644
> > --- a/drivers/gpu/drm/i915/display/intel_ddi.c
> > +++ b/drivers/gpu/drm/i915/display/intel_ddi.c
> > @@ -1761,7 +1761,14 @@ void intel_ddi_set_vc_payload_alloc(const
> > struct intel_crtc_state *crtc_state,
> >  	I915_WRITE(TRANS_DDI_FUNC_CTL(cpu_transcoder), temp);
> >  }
> >  
> > -void intel_ddi_enable_transcoder_func(const struct
> > intel_crtc_state *crtc_state)
> > +/*
> > + * Returns the TRANS_DDI_FUNC_CTL value based on CRTC state.
> > + *
> > + * Only intended to be used by intel_ddi_enable_transcoder_func()
> > and
> > + * intel_ddi_config_transcoder_func().
> > + */
> > +static u32
> > +intel_ddi_transcoder_func_reg_val_get(const struct
> > intel_crtc_state *crtc_state)
> >  {
> >  	struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
> >  	struct intel_encoder *encoder =
> > intel_ddi_get_crtc_encoder(crtc);
> > @@ -1851,6 +1858,33 @@ void intel_ddi_enable_transcoder_func(const
> > struct intel_crtc_state *crtc_state)
> >  		temp |= DDI_PORT_WIDTH(crtc_state->lane_count);
> >  	}
> >  
> > +	return temp;
> > +}
> > +
> > +void intel_ddi_enable_transcoder_func(const struct
> > intel_crtc_state *crtc_state)
> > +{
> > +	struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
> > +	struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
> > +	enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
> > +	u32 temp;
> > +
> > +	temp = intel_ddi_transcoder_func_reg_val_get(crtc_state);
> > +	I915_WRITE(TRANS_DDI_FUNC_CTL(cpu_transcoder), temp);
> > +}
> > +
> > +/*
> > + * Same as intel_ddi_enable_transcoder_func() but it do not set
> > the enable bit
> > + */
> > +static void
> > +intel_ddi_config_transcoder_func(const struct intel_crtc_state
> > *crtc_state)
> > +{
> > +	struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
> > +	struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
> > +	enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
> > +	u32 temp;
> > +
> > +	temp = intel_ddi_transcoder_func_reg_val_get(crtc_state);
> > +	temp &= ~TRANS_DDI_FUNC_ENABLE;
> >  	I915_WRITE(TRANS_DDI_FUNC_CTL(cpu_transcoder), temp);
> >  }
> >  
> > @@ -3176,9 +3210,89 @@ static void
> > intel_ddi_disable_fec_state(struct intel_encoder *encoder,
> >  	POSTING_READ(ctl);
> >  }
> >  
> > -static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
> > -				    const struct intel_crtc_state
> > *crtc_state,
> > -				    const struct drm_connector_state
> > *conn_state)
> > +static void tgl_ddi_pre_enable_dp(struct intel_encoder *encoder,
> > +				  const struct intel_crtc_state
> > *crtc_state,
> > +				  const struct drm_connector_state
> > *conn_state)
> > +{
> > +	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
> > +	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> > +	enum phy phy = intel_port_to_phy(dev_priv, encoder->port);
> > +	struct intel_digital_port *dig_port = enc_to_dig_port(&encoder-
> > >base);
> > +	bool is_mst = intel_crtc_has_type(crtc_state,
> > INTEL_OUTPUT_DP_MST);
> > +	int level = intel_ddi_dp_level(intel_dp);
> > +
> > +	intel_dp_set_link_params(intel_dp, crtc_state->port_clock,
> > +				 crtc_state->lane_count, is_mst);
> > +
> > +	/* 1.a got on intel_atomic_commit_tail() */
> > +
> > +	/* 2. */
> > +	intel_edp_panel_on(intel_dp);
> > +
> > +	/*
> > +	 * 1.b, 3. and 4. is done by before this functions by
> > +	 * haswell_crtc_enable()->intel_encoders_pre_pll_enable() and
> > +	 * haswell_crtc_enable()->intel_enable_shared_dpll()
> > +	 */
> > +
> > +	/* 5. */
> > +	if (!intel_phy_is_tc(dev_priv, phy) ||
> > +	    dig_port->tc_mode != TC_PORT_TBT_ALT)
> > +		intel_display_power_get(dev_priv,
> > +					dig_port->ddi_io_power_domain);
> > +
> > +	/* 6. */
> > +	icl_program_mg_dp_mode(dig_port);
> > +
> > +	/*
> > +	 * 7.a - Steps in this function that should only be executed
> > over MST
> > +	 * master as MST encoders will only be executed on MST master
> > as MST
> > +	 * encoder have have it's own pre_enable() hook
> > +	 */
> > +	intel_ddi_enable_pipe_clock(crtc_state);
> > +
> > +	/* 7.b */
> > +	intel_ddi_config_transcoder_func(crtc_state);
> > +
> > +	/* 7.d */
> > +	icl_disable_phy_clock_gating(dig_port);
> > +
> > +	/* 7.e */
> > +	icl_ddi_vswing_sequence(encoder, crtc_state->port_clock, level,
> > +				encoder->type);
> > +
> > +	/* 7.f */
> > +	if (intel_phy_is_combo(dev_priv, phy)) {
> > +		bool lane_reversal =
> > +			dig_port->saved_port_bits &
> > DDI_BUF_PORT_REVERSAL;
> > +
> > +		intel_combo_phy_power_up_lanes(dev_priv, phy, false,
> > +					       crtc_state->lane_count,
> > +					       lane_reversal);
> > +	}
> > +
> > +	/* 7.g */
> > +	intel_ddi_init_dp_buf_reg(encoder);
> > +
> > +	if (!is_mst)
> > +		intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
> > +
> > +	/* 7.c, 7.h, 7.i, 7.j */
> > +	intel_dp_start_link_train(intel_dp);
> > +
> > +	/* 7.k */
> > +	intel_dp_stop_link_train(intel_dp);
> > +
> > +	/* 7.l */
> > +	intel_dp_sink_set_decompression_state(intel_dp, crtc_state,
> > +					      true);
> > +	intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
> See "DDI FEC" in bspec.
> 
> intel_dp_sink_set_fec_ready() needs to be called before link
> training,
> intel_ddi_enable_fec() after.

Thanks for finding it

> 
> Presumably this is the same for DSC.

Will try to clarify it before send the fixed version.

Thanks again

> 
> > +	intel_dsc_enable(encoder, crtc_state);
> > +}
> > +
> > +static void hsw_ddi_pre_enable_dp(struct intel_encoder *encoder,
> > +				  const struct intel_crtc_state
> > *crtc_state,
> > +				  const struct drm_connector_state
> > *conn_state)
> >  {
> >  	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
> >  	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> > @@ -3244,6 +3358,18 @@ static void intel_ddi_pre_enable_dp(struct
> > intel_encoder *encoder,
> >  	intel_dsc_enable(encoder, crtc_state);
> >  }
> >  
> > +static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
> > +				    const struct intel_crtc_state
> > *crtc_state,
> > +				    const struct drm_connector_state
> > *conn_state)
> > +{
> > +	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> > +
> > +	if (INTEL_GEN(dev_priv) >= 12)
> > +		tgl_ddi_pre_enable_dp(encoder, crtc_state, conn_state);
> > +	else
> > +		hsw_ddi_pre_enable_dp(encoder, crtc_state, conn_state);
> > +}
> > +
> >  static void intel_ddi_pre_enable_hdmi(struct intel_encoder
> > *encoder,
> >  				      const struct intel_crtc_state
> > *crtc_state,
> >  				      const struct drm_connector_state
> > *conn_state)
> > diff --git a/drivers/gpu/drm/i915/display/intel_dp.c
> > b/drivers/gpu/drm/i915/display/intel_dp.c
> > index ebfcf183c7f1..1a8e041a5c43 100644
> > --- a/drivers/gpu/drm/i915/display/intel_dp.c
> > +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> > @@ -4007,13 +4007,13 @@ void intel_dp_set_idle_link_train(struct
> > intel_dp *intel_dp)
> >  	I915_WRITE(ctl, val);
> >  
> >  	/*
> > -	 * On PORT_A we can have only eDP in SST mode. There the only
> > reason
> > -	 * we need to set idle transmission mode is to work around a HW
> > issue
> > -	 * where we enable the pipe while not in idle link-training
> > mode.
> > +	 * Until TGL on PORT_A we can have only eDP in SST mode. There
> > the only
> > +	 * reason we need to set idle transmission mode is to work
> > around a HW
> > +	 * issue where we enable the pipe while not in idle link-
> > training mode.
> >  	 * In this case there is requirement to wait for a minimum
> > number of
> >  	 * idle patterns to be sent.
> >  	 */
> > -	if (port == PORT_A)
> > +	if (port == PORT_A && INTEL_GEN(dev_priv) < 12)
> >  		return;
> >  
> >  	if (intel_wait_for_register(&dev_priv->uncore, status,
> 
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx




[Index of Archives]     [AMD Graphics]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux