On Fri, May 24, 2019 at 11:32:36AM -0700, Manasi Navare wrote: > On Fri, May 24, 2019 at 07:49:07PM +0300, Imre Deak wrote: > > On Fri, May 24, 2019 at 07:27:54PM +0300, Martin Peres wrote: > > > On 23/05/2019 16:08, Imre Deak wrote: > > > > An IO failure happens if the sink is unplugged. This scenario shouldn't > > > > be logged with error level, since it is not a user visible problem. > > > > Converting the corresponding error messages to be debug messages also > > > > ensures that we don't fail some CI test incorrectly that tests the > > > > unplugging while a mode is still active on the given connector (like the > > > > kms_chamelium tests imititating such an unplug during being suspended). > > > > > > > > Leave those link training error messages that are due to an actual > > > > transfer rate error (and not an IO error) as-is, as that kind of problem > > > > is related to the user's configuration (cable, mode, monitor) and so it > > > > is really user visible. > > > > > > Are there some scenarios that would be warranting a DRM_ERROR? If so, > > > then we should decide on the verbosity based on wether the connector is > > > connected or disconnected, don't you think? > > > > I don't think we should depend on the correctness of setting the message > > level correctly based on the live state, since the live state itself is > > flaky/unreliable based on the timing of the unplug vs. the settling of > > the live state flag. For instance we could see the AUX IO failing > > already but live state still indicating that the sink is plugged, so > > we'd print again an error instead of the correct tuned-down note. > > But in case of AUX failures which we see a lot when AUX power > is accidently off or eDP is still not ON or sink is unplugged while > the link training was in process, doesnt it make sense to > call it as a DRM_ERROR and not just a DEBUG_KMS. Logging such AUX fails as DEBUG makes sense, since it will be up to a developer to look through the logs if needed; for instance if it leads to failing the actual link training logged with DRM_ERROR or failing the detection when you expect the sink to be there. Otoh, it's a bad thing to log such AUX fails as DRM_ERROR as will result in failing tests incorrectly when the sink is disconnected and the AUX fails happen as expected. > For Eg: the CI tests failed due to AUX timeouts should be the actual failures > which would be filtered now if we tune it down to DEBUG_KMS. These will lead to actually failing the detection/link training, which you can depend on failing the tests instead of depending on error messages in dmesg. > > Manasi > > > > > > > Martin > > > > > > > > Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110390 > > > > Signed-off-by: Imre Deak <imre.deak@xxxxxxxxx> > > > > --- > > > > drivers/gpu/drm/i915/intel_dp_link_training.c | 12 ++++++------ > > > > 1 file changed, 6 insertions(+), 6 deletions(-) > > > > > > > > diff --git a/drivers/gpu/drm/i915/intel_dp_link_training.c b/drivers/gpu/drm/i915/intel_dp_link_training.c > > > > index 9b1fccea966b..392ebeb89ce8 100644 > > > > --- a/drivers/gpu/drm/i915/intel_dp_link_training.c > > > > +++ b/drivers/gpu/drm/i915/intel_dp_link_training.c > > > > @@ -169,7 +169,7 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp) > > > > if (!intel_dp_reset_link_train(intel_dp, > > > > DP_TRAINING_PATTERN_1 | > > > > DP_LINK_SCRAMBLING_DISABLE)) { > > > > - DRM_ERROR("failed to enable link training\n"); > > > > + DRM_DEBUG_KMS("failed to enable link training\n"); > > > > return false; > > > > } > > > > > > > > @@ -193,7 +193,7 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp) > > > > drm_dp_link_train_clock_recovery_delay(intel_dp->dpcd); > > > > > > > > if (!intel_dp_get_link_status(intel_dp, link_status)) { > > > > - DRM_ERROR("failed to get link status\n"); > > > > + DRM_DEBUG_KMS("failed to get link status\n"); > > > > return false; > > > > } > > > > > > > > @@ -217,7 +217,7 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp) > > > > /* Update training set as requested by target */ > > > > intel_get_adjust_train(intel_dp, link_status); > > > > if (!intel_dp_update_link_train(intel_dp)) { > > > > - DRM_ERROR("failed to update link training\n"); > > > > + DRM_DEBUG_KMS("failed to update link training\n"); > > > > return false; > > > > } > > > > > > > > @@ -295,7 +295,7 @@ intel_dp_link_training_channel_equalization(struct intel_dp *intel_dp) > > > > /* channel equalization */ > > > > if (!intel_dp_set_link_train(intel_dp, > > > > training_pattern)) { > > > > - DRM_ERROR("failed to start channel equalization\n"); > > > > + DRM_DEBUG_KMS("failed to start channel equalization\n"); > > > > return false; > > > > } > > > > > > > > @@ -303,7 +303,7 @@ intel_dp_link_training_channel_equalization(struct intel_dp *intel_dp) > > > > > > > > drm_dp_link_train_channel_eq_delay(intel_dp->dpcd); > > > > if (!intel_dp_get_link_status(intel_dp, link_status)) { > > > > - DRM_ERROR("failed to get link status\n"); > > > > + DRM_DEBUG_KMS("failed to get link status\n"); > > > > break; > > > > } > > > > > > > > @@ -327,7 +327,7 @@ intel_dp_link_training_channel_equalization(struct intel_dp *intel_dp) > > > > /* Update training set as requested by target */ > > > > intel_get_adjust_train(intel_dp, link_status); > > > > if (!intel_dp_update_link_train(intel_dp)) { > > > > - DRM_ERROR("failed to update link training\n"); > > > > + DRM_DEBUG_KMS("failed to update link training\n"); > > > > break; > > > > } > > > > } > > > > > > > > > _______________________________________________ > > Intel-gfx mailing list > > Intel-gfx@xxxxxxxxxxxxxxxxxxxxx > > https://lists.freedesktop.org/mailman/listinfo/intel-gfx _______________________________________________ Intel-gfx mailing list Intel-gfx@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/intel-gfx