- Regroup definitions for BLC_PWM_CTL so that they're all together and and ordered according to the bitfields. - Add all missing defintions for BLC_PWM_CTL2. - Use the BLM_ (for backlight modulation) prefix consistently. - Note that combination mode (i.e. also taking the legacy backlight control value from pci config space into account) is gen4 only. - Move the new registers for PCH-split machines up, they're an almost match for the gen4 defitions. Prefix the special PCH-only bits with BLM_PCH_. Also add the pipe C select bit for ivb. - Rip out the second pair of PCH polarity definitions - they're only valid on early (pre-production) ilk silicon. - Adapt the existing code to use the new definitions. This has the nice benefit of killing a magic (1 << 30) left behind be Jesse Barnes. No functional changes in this patch. Signed-off-by: Daniel Vetter <daniel.vetter at ffwll.ch> --- drivers/gpu/drm/i915/i915_reg.h | 55 +++++++++++++++++++++------------ drivers/gpu/drm/i915/intel_display.c | 4 +- drivers/gpu/drm/i915/intel_lvds.c | 12 ++++---- 3 files changed, 43 insertions(+), 28 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 20244b9..c4b1a2b 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -1807,18 +1807,35 @@ #define PFIT_AUTO_RATIOS 0x61238 /* Backlight control */ -#define BLC_PWM_CTL 0x61254 -#define BACKLIGHT_MODULATION_FREQ_SHIFT (17) #define BLC_PWM_CTL2 0x61250 /* 965+ only */ -#define BLM_COMBINATION_MODE (1 << 30) +#define BLM_PWM_ENABLE (1 << 31) +#define BLM_COMBINATION_MODE (1 << 30) /* gen4 only */ +#define BLM_PIPE_SELECT (1 << 29) +#define BLM_PIPE_SELECT_IVB (3 << 29) +#define BLM_PIPE_A (0 << 29) +#define BLM_PIPE_B (1 << 29) +#define BLM_PIPE_C (2 << 29) /* ivb + */ +#define BLM_PIPE(pipe) ((pipe) << 29) +#define BLM_POLARITY_I965 (1 << 28) /* gen4 only */ +#define BLM_PHASE_IN_INTERUPT_STATUS (1 << 26) +#define BLM_PHASE_IN_ENABLE (1 << 25) +#define BLM_PHASE_IN_INTERUPT_ENABL (1 << 24) +#define BLM_PHASE_IN_TIME_BASE_SHIFT (16) +#define BLM_PHASE_IN_TIME_BASE_MASK (0xff << 16) +#define BLM_PHASE_IN_COUNT_SHIFT (8) +#define BLM_PHASE_IN_COUNT_MASK (0xff << 8) +#define BLM_PHASE_IN_INCR_SHIFT (0) +#define BLM_PHASE_IN_INCR_MASK (0xff << 0) +#define BLC_PWM_CTL 0x61254 /* * This is the most significant 15 bits of the number of backlight cycles in a * complete cycle of the modulated backlight control. * * The actual value is this field multiplied by two. */ -#define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17) -#define BLM_LEGACY_MODE (1 << 16) +#define BACKLIGHT_MODULATION_FREQ_SHIFT (17) +#define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17) +#define BLM_LEGACY_MODE (1 << 16) /* gen2 only */ /* * This is the number of cycles out of the backlight modulation cycle for which * the backlight is on. @@ -1833,6 +1850,19 @@ #define BLC_HIST_CTL 0x61260 +/* New registers for PCH-split platforms. Safe where new bits show up, the + * register layout machtes with gen4 BLC_PWM_CTL[12]. */ +#define BLC_PWM_CPU_CTL2 0x48250 +#define BLC_PWM_CPU_CTL 0x48254 + +/* PCH CTL1 is totally different, all but the below bits are reserved. CTL2 is + * like the normal CTL from gen4 and earlier. Hooray for confusing naming. */ +#define BLC_PWM_PCH_CTL1 0xc8250 +#define BLM_PCH_PWM_ENABLE (1 << 30) +#define BLM_PCH_OVERRIDE_ENABLE (1 << 30) +#define BLM_PCH_POLARITY (1 << 29) +#define BLC_PWM_PCH_CTL2 0xc8254 + /* TV port control */ #define TV_CTL 0x68000 /** Enables the TV encoder */ @@ -3840,21 +3870,6 @@ #define PCH_LVDS 0xe1180 #define LVDS_DETECTED (1 << 1) -#define BLC_PWM_CPU_CTL2 0x48250 -#define PWM_ENABLE (1 << 31) -#define PWM_PIPE_A (0 << 29) -#define PWM_PIPE_B (1 << 29) -#define BLC_PWM_CPU_CTL 0x48254 - -#define BLC_PWM_PCH_CTL1 0xc8250 -#define PWM_PCH_ENABLE (1 << 31) -#define PWM_POLARITY_ACTIVE_LOW (1 << 29) -#define PWM_POLARITY_ACTIVE_HIGH (0 << 29) -#define PWM_POLARITY_ACTIVE_LOW2 (1 << 28) -#define PWM_POLARITY_ACTIVE_HIGH2 (0 << 28) - -#define BLC_PWM_PCH_CTL2 0xc8254 - #define PCH_PP_STATUS 0xc7200 #define PCH_PP_CONTROL 0xc7204 #define PANEL_UNLOCK_REGS (0xabcd << 16) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 9f5148ac..5cc1e9b 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -6889,9 +6889,9 @@ static void ivb_pch_pwm_override(struct drm_device *dev) * IVB has CPU eDP backlight regs too, set things up to let the * PCH regs control the backlight */ - I915_WRITE(BLC_PWM_CPU_CTL2, PWM_ENABLE); + I915_WRITE(BLC_PWM_CPU_CTL2, BLM_PWM_ENABLE); I915_WRITE(BLC_PWM_CPU_CTL, 0); - I915_WRITE(BLC_PWM_PCH_CTL1, PWM_ENABLE | (1<<30)); + I915_WRITE(BLC_PWM_PCH_CTL1, BLM_PCH_PWM_ENABLE | BLM_PCH_OVERRIDE_ENABLE); } void intel_modeset_init_hw(struct drm_device *dev) diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c index 08eb04c..a7269e6 100644 --- a/drivers/gpu/drm/i915/intel_lvds.c +++ b/drivers/gpu/drm/i915/intel_lvds.c @@ -1081,16 +1081,16 @@ out: /* make sure PWM is enabled and locked to the LVDS pipe */ pwm = I915_READ(BLC_PWM_CPU_CTL2); - if (pipe == 0 && (pwm & PWM_PIPE_B)) - I915_WRITE(BLC_PWM_CPU_CTL2, pwm & ~PWM_ENABLE); + if (pipe == 0 && (pwm & BLM_PIPE_B)) + I915_WRITE(BLC_PWM_CPU_CTL2, pwm & ~BLM_PWM_ENABLE); if (pipe) - pwm |= PWM_PIPE_B; + pwm |= BLM_PIPE_B; else - pwm &= ~PWM_PIPE_B; - I915_WRITE(BLC_PWM_CPU_CTL2, pwm | PWM_ENABLE); + pwm &= ~BLM_PIPE_B; + I915_WRITE(BLC_PWM_CPU_CTL2, pwm | BLM_PWM_ENABLE); pwm = I915_READ(BLC_PWM_PCH_CTL1); - pwm |= PWM_PCH_ENABLE; + pwm |= BLM_PCH_PWM_ENABLE; I915_WRITE(BLC_PWM_PCH_CTL1, pwm); /* * Unlock registers and just -- 1.7.7.6
