Only support runtime changes through the debugfs. i915.verbose_state_checks remains an exception, and is not exposed via debugfs. FIXME: Before this gets applied, IGT needs to be changed to use the debugfs for modifying the parameters. IGT changes at least the following through module parameter sysfs: * enable_fbc * reset * enable_hangcheck * enable_psr * fastboot * prefault_disable * load_detect_test * force_reset_modeset_test Signed-off-by: Jani Nikula <jani.nikula@xxxxxxxxx> --- drivers/gpu/drm/i915/i915_params.c | 40 ++++++++++++++++++++++++-------------- 1 file changed, 25 insertions(+), 15 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_params.c b/drivers/gpu/drm/i915/i915_params.c index b1a8b8f7dac9..61cde445346e 100644 --- a/drivers/gpu/drm/i915/i915_params.c +++ b/drivers/gpu/drm/i915/i915_params.c @@ -40,6 +40,15 @@ struct i915_params i915_modparams __read_mostly = { #undef MEMBER }; +/* + * Note: As a rule, keep module parameter sysfs permissions read-only + * 0400. Runtime changes are only supported through i915 debugfs. + * + * For any exceptions requiring write access and runtime changes through module + * parameter sysfs, prevent debugfs file creation by setting the parameter's + * debugfs mode to 0. + */ + i915_param_named(modeset, int, 0400, "Use kernel modesetting [KMS] (0=disable, " "1=on, -1=force vga console preference [default])"); @@ -48,7 +57,7 @@ i915_param_named_unsafe(enable_dc, int, 0400, "Enable power-saving display C-states. " "(-1=auto [default]; 0=disable; 1=up to DC5; 2=up to DC6)"); -i915_param_named_unsafe(enable_fbc, int, 0600, +i915_param_named_unsafe(enable_fbc, int, 0400, "Enable frame buffer compression for power savings " "(default: -1 (use per-chip default))"); @@ -56,7 +65,7 @@ i915_param_named_unsafe(lvds_channel_mode, int, 0400, "Specify LVDS channel mode " "(0=probe BIOS [default], 1=single-channel, 2=dual-channel)"); -i915_param_named_unsafe(panel_use_ssc, int, 0600, +i915_param_named_unsafe(panel_use_ssc, int, 0400, "Use Spread Spectrum Clock with panels [LVDS/eDP] " "(default: auto from VBT)"); @@ -64,25 +73,25 @@ i915_param_named_unsafe(vbt_sdvo_panel_type, int, 0400, "Override/Ignore selection of SDVO panel mode in the VBT " "(-2=ignore, -1=auto [default], index in VBT BIOS table)"); -i915_param_named_unsafe(reset, int, 0600, +i915_param_named_unsafe(reset, int, 0400, "Attempt GPU resets (0=disabled, 1=full gpu reset, 2=engine reset [default])"); i915_param_named_unsafe(vbt_firmware, charp, 0400, "Load VBT from specified file under /lib/firmware"); #if IS_ENABLED(CONFIG_DRM_I915_CAPTURE_ERROR) -i915_param_named(error_capture, bool, 0600, +i915_param_named(error_capture, bool, 0400, "Record the GPU state following a hang. " "This information in /sys/class/drm/card<N>/error is vital for " "triaging and debugging hangs."); #endif -i915_param_named_unsafe(enable_hangcheck, bool, 0600, +i915_param_named_unsafe(enable_hangcheck, bool, 0400, "Periodically check GPU activity for detecting hangs. " "WARNING: Disabling this can cause system wide hangs. " "(default: true)"); -i915_param_named_unsafe(enable_psr, int, 0600, +i915_param_named_unsafe(enable_psr, int, 0400, "Enable PSR " "(0=disabled, 1=enabled) " "Default: -1 (use per-chip default)"); @@ -95,24 +104,24 @@ i915_param_named_unsafe(disable_power_well, int, 0400, "Disable display power wells when possible " "(-1=auto [default], 0=power wells always on, 1=power wells disabled when possible)"); -i915_param_named_unsafe(enable_ips, int, 0600, "Enable IPS (default: true)"); +i915_param_named_unsafe(enable_ips, int, 0400, "Enable IPS (default: true)"); -i915_param_named(fastboot, bool, 0600, +i915_param_named(fastboot, bool, 0400, "Try to skip unnecessary mode sets at boot time (default: false)"); -i915_param_named_unsafe(prefault_disable, bool, 0600, +i915_param_named_unsafe(prefault_disable, bool, 0400, "Disable page prefaulting for pread/pwrite/reloc (default:false). " "For developers only."); -i915_param_named_unsafe(load_detect_test, bool, 0600, +i915_param_named_unsafe(load_detect_test, bool, 0400, "Force-enable the VGA load detect code for testing (default:false). " "For developers only."); -i915_param_named_unsafe(force_reset_modeset_test, bool, 0600, +i915_param_named_unsafe(force_reset_modeset_test, bool, 0400, "Force a modeset during gpu reset for testing (default:false). " "For developers only."); -i915_param_named_unsafe(invert_brightness, int, 0600, +i915_param_named_unsafe(invert_brightness, int, 0400, "Invert backlight brightness " "(-1 force normal, 0 machine defaults, 1 force inversion), please " "report PCI device ID, subsystem vendor and subsystem device ID " @@ -122,10 +131,11 @@ i915_param_named_unsafe(invert_brightness, int, 0600, i915_param_named(disable_display, bool, 0400, "Disable display (default: false)"); -i915_param_named(mmio_debug, int, 0600, +i915_param_named(mmio_debug, int, 0400, "Enable the MMIO debug code for the first N failures (default: off). " "This may negatively affect performance."); +/* Special case writable file */ i915_param_named(verbose_state_checks, bool, 0600, "Enable verbose logs (ie. WARN_ON()) in case of unexpected hw state conditions."); @@ -156,10 +166,10 @@ i915_param_named_unsafe(huc_firmware_path, charp, 0400, i915_param_named_unsafe(dmc_firmware_path, charp, 0400, "DMC firmware path to use instead of the default one"); -i915_param_named_unsafe(enable_dp_mst, bool, 0600, +i915_param_named_unsafe(enable_dp_mst, bool, 0400, "Enable multi-stream transport (MST) for new DisplayPort sinks. (default: true)"); -i915_param_named(enable_dpcd_backlight, bool, 0600, +i915_param_named(enable_dpcd_backlight, bool, 0400, "Enable support for DPCD backlight control (default:false)"); #if IS_ENABLED(CONFIG_DRM_I915_GVT) -- 2.11.0 _______________________________________________ Intel-gfx mailing list Intel-gfx@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/intel-gfx