On Tue, Nov 06, 2018 at 04:51:22PM +0200, Ville Syrjälä wrote:
> On Mon, Nov 05, 2018 at 04:48:57PM -0800, Manasi Navare wrote:
> > On Mon, Nov 05, 2018 at 03:31:48PM -0800, Anusha Srivatsa wrote:
> > > If the panel supports FEC, the driver has to
> > > set the FEC_READY bit in the dpcd register:
> > > FEC_CONFIGURATION.
> > >
> > > This has to happen before link training.
> > >
> > > v2: s/intel_dp_set_fec_ready/intel_dp_sink_set_fec_ready
> > > - change commit message. (Gaurav)
> > >
> > > v3: rebased. (r-b Manasi)
> > >
> > > v4: Use fec crtc state, before setting FEC_READY
> > > bit. (Anusha)
> > >
> > > v5: Move to intel_ddi.c
> > > - Make the function static (Anusha)
> > >
> > > Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx
> > > Cc: Gaurav K Singh <gaurav.k.singh@xxxxxxxxx>
> > > Cc: Jani Nikula <jani.nikula@xxxxxxxxxxxxxxx>
> > > Cc: Ville Syrjala <ville.syrjala@xxxxxxxxxxxxxxx>
> > > Cc: Manasi Navare <manasi.d.navare@xxxxxxxxx>
> > > Signed-off-by: Anusha Srivatsa <anusha.srivatsa@xxxxxxxxx>
> > > ---
> > > drivers/gpu/drm/i915/intel_ddi.c | 15 +++++++++++++++
> > > 1 file changed, 15 insertions(+)
> > >
> > > diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
> > > index 46c1b9e12fbd..53a9b31e66a2 100644
> > > --- a/drivers/gpu/drm/i915/intel_ddi.c
> > > +++ b/drivers/gpu/drm/i915/intel_ddi.c
> > > @@ -3051,6 +3051,20 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port)
> > > I915_WRITE(MG_DP_MODE(port, 1), ln1);
> > > }
> > >
> > > +static void intel_dp_sink_set_fec_ready(struct intel_dp *intel_dp,
> > > + const struct intel_crtc_state *crtc_state,
> > > + int state)
> >
> > u8 state should be good enough since you are writing only a byte here
>
> AFAICS this is never called with anything but DP_FEC_READY. So
> there is absolutely benefit in making the caller have to
> pass that in. Just drop the 'state' argument entirely IMO.
Oh yes thats correct, its a constant at DRM level and can be used directly since state never really gets set to
DP_FEC_NOT_READy.
Manasi
>
> >
> > > +{
> > > + int ret;
> > > +
> > > + if (!crtc_state->fec_enable)
> > > + return;
> > > +
> > > + ret = drm_dp_dpcd_writeb(&intel_dp->aux, DP_FEC_CONFIGURATION, state);
> > > + if (ret < 0)
> >
> > This should ret <=0 since even if it writes 0 bytes its an error. Infact you dont need ret
> > you can just say"
> > if (drm_dp_dpcd_writeb(&intel_dp->aux, DP_FEC_CONFIGURATION, state) <= 0)
> >
> > After the above changes,
> >
> > Reviewed-by: Manasi Navare <manasi.d.navare@xxxxxxxxx>
> >
> > Manasi
> > > + DRM_DEBUG_KMS("Failed to get FEC enabled in sink\n");
>
> This debug msg doesn't make sense.
>
> > > +}
> > > +
> > > static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
> > > const struct intel_crtc_state *crtc_state,
> > > const struct drm_connector_state *conn_state)
> > > @@ -3091,6 +3105,7 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
> > > intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
> > > intel_dp_sink_set_decompression_state(intel_dp, crtc_state,
> > > true);
> > > + intel_dp_sink_set_fec_ready(intel_dp, crtc_state, DP_FEC_READY);
> > > intel_dp_start_link_train(intel_dp);
> > > if (port != PORT_A || INTEL_GEN(dev_priv) >= 9)
> > > intel_dp_stop_link_train(intel_dp);
> > > --
> > > 2.19.1
> > >
>
> --
> Ville Syrjälä
> Intel
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
