Hi,
On 19-10-18 11:20, Jani Nikula wrote:
On Wed, 17 Oct 2018, Hans de Goede <j.w.r.degoede@xxxxxxxxx> wrote:
On BYT and CHT the GOP sometimes initializes the pclk at a (slightly)
different frequency then the pclk which we've calculated.
This commit makes the DSI code read-back the pclk set by the GOP and
if that is within a reasonable margin of the calculated pclk, uses
that instead.
This fixes the first modeset being a full modeset instead of a
fast modeset on systems where the GOP pclk is different.
I assume we don't do the fast path because intel_pipe_config_compare()
returns false due to crtc_clock and port_clock mismatch. The dmesg
should tell you the reason with drm.debugs enabled.
As I think I mentioned already last time (but that was a while ago,
so I understand you cannot remember the details), the problem is these
checks from intel_pipe_config_compare():
PIPE_CONF_CHECK_X(dsi_pll.ctrl);
PIPE_CONF_CHECK_X(dsi_pll.div);
Now, the clock checks are already "fuzzy", and should account for slight
variations. I think the goal was the same as here, plus IIUC we may lose
some accuracy on the hardware roundtrip.
The check I quoted above are basically doing a non-fuzzy port_clock check,
we already do a fuzzy port_clock check, so maybe we should just drop them?
Please try adding more tolerance in intel_fuzzy_clock_check() and see if
that helps. The code looks like it allows 5% diff, but it's 2.5%.
Regardless of whether we end up changing the tolerance or adjusting the
state based on the hardware readout or what, I think doing the
adjustment in intel_dsi_vbt.c init is the wrong place. We shouldn't have
anything that depends on accessing the hardware there. I believe that's
what Ville was trying to say in [1].
If you agree with dropping these 2 in essence non-fuzzy port-clock checks:
PIPE_CONF_CHECK_X(dsi_pll.ctrl);
PIPE_CONF_CHECK_X(dsi_pll.div);
Then we won't need this state adjustment.
But in case you do want to keep these, then were should the adjustment be done?
Keep in mind that the pclk is initially calculated in intel_dsi_vbt.c
and then immediately used to calculate a bunch of other settings such as
intel_dsi->lp_byte_clk, prepare_cnt, etc. So there really is no other
place were we can reasonably do this.
Regards,
Hans
BR,
Jani.
[1] http://mid.mail-archive.com/20180706141652.GK5565@xxxxxxxxx
Changes in v2:
-Use intel_encoder_current_mode() to get the pclk setup by the GOP
Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
---
drivers/gpu/drm/i915/intel_dsi_vbt.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/drivers/gpu/drm/i915/intel_dsi_vbt.c b/drivers/gpu/drm/i915/intel_dsi_vbt.c
index ac83d6b89ae0..3387b187105c 100644
--- a/drivers/gpu/drm/i915/intel_dsi_vbt.c
+++ b/drivers/gpu/drm/i915/intel_dsi_vbt.c
@@ -506,6 +506,7 @@ bool intel_dsi_vbt_init(struct intel_dsi *intel_dsi, u16 panel_id)
struct mipi_config *mipi_config = dev_priv->vbt.dsi.config;
struct mipi_pps_data *pps = dev_priv->vbt.dsi.pps;
struct drm_display_mode *mode = dev_priv->vbt.lfp_lvds_vbt_mode;
+ struct drm_display_mode *curr;
u32 bpp;
u32 tlpx_ns, extra_byte_count, bitrate, tlpx_ui;
u32 ui_num, ui_den;
@@ -583,6 +584,23 @@ bool intel_dsi_vbt_init(struct intel_dsi *intel_dsi, u16 panel_id)
} else
burst_mode_ratio = 100;
+ /*
+ * On BYT / CRC the GOP sometimes picks a slightly different pclk,
+ * read back the GOP configured pclk and prefer it over ours.
+ */
+ if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) {
+ curr = intel_encoder_current_mode(&intel_dsi->base);
+ if (curr) {
+ DRM_DEBUG_KMS("Calculated pclk %d GOP %d\n",
+ pclk, curr->clock);
+ if (curr->clock >= (pclk * 9 / 10) &&
+ curr->clock <= (pclk * 11 / 10))
+ pclk = curr->clock;
+
+ kfree(curr);
+ }
+ }
+
intel_dsi->burst_mode_ratio = burst_mode_ratio;
intel_dsi->pclk = pclk;
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
