On 18/10/18 12:55, Chris Wilson wrote:
Propagate the timeout on transferring the fw back to the caller where it
may act upon it, usually by restarting the xfer before failing.
v2: Simplify the wait to only wait upon the guc signaling completion,
with an assertion that the fw xfer must have completed for it to be
ready!
Testcase: igt/drv_selftest/live_hangcheck
Signed-off-by: Chris Wilson <chris@xxxxxxxxxxxxxxxxxx>
Cc: Michal Wajdeczko <michal.wajdeczko@xxxxxxxxx>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@xxxxxxxxx>
---
drivers/gpu/drm/i915/intel_guc_fw.c | 106 +++++++++++++---------------
1 file changed, 50 insertions(+), 56 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_guc_fw.c b/drivers/gpu/drm/i915/intel_guc_fw.c
index a9e6fcce467c..51b292001edd 100644
--- a/drivers/gpu/drm/i915/intel_guc_fw.c
+++ b/drivers/gpu/drm/i915/intel_guc_fw.c
@@ -125,66 +125,26 @@ static void guc_prepare_xfer(struct intel_guc *guc)
}
/* Copy RSA signature from the fw image to HW for verification */
-static int guc_xfer_rsa(struct intel_guc *guc, struct i915_vma *vma)
+static void guc_xfer_rsa(struct intel_guc *guc, struct i915_vma *vma)
{
struct drm_i915_private *dev_priv = guc_to_i915(guc);
- struct intel_uc_fw *guc_fw = &guc->fw;
- struct sg_table *sg = vma->pages;
u32 rsa[UOS_RSA_SCRATCH_COUNT];
int i;
- if (sg_pcopy_to_buffer(sg->sgl, sg->nents, rsa, sizeof(rsa),
- guc_fw->rsa_offset) != sizeof(rsa))
- return -EINVAL;
+ sg_pcopy_to_buffer(vma->pages->sgl, vma->pages->nents,
+ rsa, sizeof(rsa), guc->fw.rsa_offset);
for (i = 0; i < UOS_RSA_SCRATCH_COUNT; i++)
I915_WRITE(UOS_RSA_SCRATCH(i), rsa[i]);
-
- return 0;
}
-/*
- * Transfer the firmware image to RAM for execution by the microcontroller.
- *
- * Architecturally, the DMA engine is bidirectional, and can potentially even
- * transfer between GTT locations. This functionality is left out of the API
- * for now as there is no need for it.
- */
-static int guc_xfer_ucode(struct intel_guc *guc, struct i915_vma *vma)
+static bool guc_xfer_completed(struct intel_guc *guc, u32 *status)
{
struct drm_i915_private *dev_priv = guc_to_i915(guc);
- struct intel_uc_fw *guc_fw = &guc->fw;
- unsigned long offset;
- u32 status;
- int ret;
-
- /*
- * The header plus uCode will be copied to WOPCM via DMA, excluding any
- * other components
- */
- I915_WRITE(DMA_COPY_SIZE, guc_fw->header_size + guc_fw->ucode_size);
-
- /* Set the source address for the new blob */
- offset = intel_guc_ggtt_offset(guc, vma) + guc_fw->header_offset;
- I915_WRITE(DMA_ADDR_0_LOW, lower_32_bits(offset));
- I915_WRITE(DMA_ADDR_0_HIGH, upper_32_bits(offset) & 0xFFFF);
- /*
- * Set the DMA destination. Current uCode expects the code to be
- * loaded at 8k; locations below this are used for the stack.
- */
- I915_WRITE(DMA_ADDR_1_LOW, 0x2000);
- I915_WRITE(DMA_ADDR_1_HIGH, DMA_ADDRESS_SPACE_WOPCM);
-
- /* Finally start the DMA */
- I915_WRITE(DMA_CTRL, _MASKED_BIT_ENABLE(UOS_MOVE | START_DMA));
-
- /* Wait for DMA to finish */
- ret = __intel_wait_for_register_fw(dev_priv, DMA_CTRL, START_DMA, 0,
- 2, 100, &status);
- DRM_DEBUG_DRIVER("GuC DMA status %#x\n", status);
-
- return ret;
+ /* Did we complete the xfer? */
+ *status = I915_READ(DMA_CTRL);
+ return !(*status & START_DMA);
}
/*
@@ -228,9 +188,51 @@ static int guc_wait_ucode(struct intel_guc *guc)
ret = -ENOEXEC;
}
+ if (ret == 0 && !guc_xfer_completed(guc, &status)) {
+ DRM_ERROR("GuC is ready, but the xfer %08x is incomplete\n",
+ status);
+ ret = -ENXIO;
Do we want to allow reset & retry in this scenario? This feels like
something weird happening in HW, so I'd say it'd be worth to allow a retry.
Thanks,
Daniele
+ }
+
return ret;
}
+/*
+ * Transfer the firmware image to RAM for execution by the microcontroller.
+ *
+ * Architecturally, the DMA engine is bidirectional, and can potentially even
+ * transfer between GTT locations. This functionality is left out of the API
+ * for now as there is no need for it.
+ */
+static int guc_xfer_ucode(struct intel_guc *guc, struct i915_vma *vma)
+{
+ struct drm_i915_private *dev_priv = guc_to_i915(guc);
+ struct intel_uc_fw *guc_fw = &guc->fw;
+ unsigned long offset;
+
+ /*
+ * The header plus uCode will be copied to WOPCM via DMA, excluding any
+ * other components
+ */
+ I915_WRITE(DMA_COPY_SIZE, guc_fw->header_size + guc_fw->ucode_size);
+
+ /* Set the source address for the new blob */
+ offset = intel_guc_ggtt_offset(guc, vma) + guc_fw->header_offset;
+ I915_WRITE(DMA_ADDR_0_LOW, lower_32_bits(offset));
+ I915_WRITE(DMA_ADDR_0_HIGH, upper_32_bits(offset) & 0xFFFF);
+
+ /*
+ * Set the DMA destination. Current uCode expects the code to be
+ * loaded at 8k; locations below this are used for the stack.
+ */
+ I915_WRITE(DMA_ADDR_1_LOW, 0x2000);
+ I915_WRITE(DMA_ADDR_1_HIGH, DMA_ADDRESS_SPACE_WOPCM);
+
+ /* Finally start the DMA */
+ I915_WRITE(DMA_CTRL, _MASKED_BIT_ENABLE(UOS_MOVE | START_DMA));
+
+ return guc_wait_ucode(guc);
+}
/*
* Load the GuC firmware blob into the MinuteIA.
*/
@@ -251,17 +253,9 @@ static int guc_fw_xfer(struct intel_uc_fw *guc_fw, struct i915_vma *vma)
* by the DMA engine in one operation, whereas the RSA signature is
* loaded via MMIO.
*/
- ret = guc_xfer_rsa(guc, vma);
- if (ret)
- DRM_WARN("GuC firmware signature xfer error %d\n", ret);
+ guc_xfer_rsa(guc, vma);
ret = guc_xfer_ucode(guc, vma);
- if (ret)
- DRM_WARN("GuC firmware code xfer error %d\n", ret);
-
- ret = guc_wait_ucode(guc);
- if (ret)
- DRM_ERROR("GuC firmware xfer error %d\n", ret);
intel_uncore_forcewake_put(dev_priv, FORCEWAKE_ALL);
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
