From: Madhav Chauhan <madhav.chauhan@xxxxxxxxx>
As part of DSI enable sequence, transcoder timings
(horizontal & vertical) need to be set so that transcoder
will generate the stream output as per those timings.
This patch set required transcoder timings as per BSPEC.
v2: Remove TRANS_TIMING_SHIFT usage
v3 by Jani:
- Rebase
- Reduce temp variable use
- Checkpatch fix
Signed-off-by: Madhav Chauhan <madhav.chauhan@xxxxxxxxx>
Signed-off-by: Jani Nikula <jani.nikula@xxxxxxxxx>
---
drivers/gpu/drm/i915/icl_dsi.c | 118 +++++++++++++++++++++++++++++++++++++++++
1 file changed, 118 insertions(+)
diff --git a/drivers/gpu/drm/i915/icl_dsi.c b/drivers/gpu/drm/i915/icl_dsi.c
index 87d5e6435791..f6ed57b28676 100644
--- a/drivers/gpu/drm/i915/icl_dsi.c
+++ b/drivers/gpu/drm/i915/icl_dsi.c
@@ -477,6 +477,121 @@ gen11_dsi_configure_transcoder(struct intel_encoder *encoder,
}
static void
+gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
+ const struct intel_crtc_state *pipe_config)
+{
+ struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+ struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
+ const struct drm_display_mode *adjusted_mode =
+ &pipe_config->base.adjusted_mode;
+ enum port port;
+ enum transcoder dsi_trans;
+ /* horizontal timings */
+ u16 htotal, hactive, hsync_start, hsync_end, hsync_size;
+ u16 hfront_porch, hback_porch;
+ /* vertical timings */
+ u16 vtotal, vactive, vsync_start, vsync_end, vsync_shift;
+
+ hactive = adjusted_mode->crtc_hdisplay;
+ htotal = adjusted_mode->crtc_htotal;
+ hsync_start = adjusted_mode->crtc_hsync_start;
+ hsync_end = adjusted_mode->crtc_hsync_end;
+ hsync_size = hsync_end - hsync_start;
+ hfront_porch = (adjusted_mode->crtc_hsync_start -
+ adjusted_mode->crtc_hdisplay);
+ hback_porch = (adjusted_mode->crtc_htotal -
+ adjusted_mode->crtc_hsync_end);
+ vactive = adjusted_mode->crtc_vdisplay;
+ vtotal = adjusted_mode->crtc_vtotal;
+ vsync_start = adjusted_mode->crtc_vsync_start;
+ vsync_end = adjusted_mode->crtc_vsync_end;
+ vsync_shift = hsync_start - htotal / 2;
+
+ if (intel_dsi->dual_link) {
+ hactive /= 2;
+ if (intel_dsi->dual_link == DSI_DUAL_LINK_FRONT_BACK)
+ hactive += intel_dsi->pixel_overlap;
+ htotal /= 2;
+ }
+
+ /* minimum hactive as per bspec: 256 pixels */
+ if (adjusted_mode->crtc_hdisplay < 256)
+ DRM_ERROR("hactive is less then 256 pixels\n");
+
+ /* if RGB666 format, then hactive must be multiple of 4 pixels */
+ if (intel_dsi->pixel_format == MIPI_DSI_FMT_RGB666 && hactive % 4 != 0)
+ DRM_ERROR("hactive pixels are not multiple of 4\n");
+
+ /* program TRANS_HTOTAL register */
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ I915_WRITE(HTOTAL(dsi_trans),
+ (hactive - 1) | ((htotal - 1) << 16));
+ }
+
+ /* TRANS_HSYNC register to be programmed only for video mode */
+ if (intel_dsi->operation_mode == INTEL_DSI_VIDEO_MODE) {
+ if (intel_dsi->video_mode_format ==
+ VIDEO_MODE_NON_BURST_WITH_SYNC_PULSE) {
+ /* BSPEC: hsync size should be atleast 16 pixels */
+ if (hsync_size < 16)
+ DRM_ERROR("hsync size < 16 pixels\n");
+ }
+
+ if (hback_porch < 16)
+ DRM_ERROR("hback porch < 16 pixels\n");
+
+ if (intel_dsi->dual_link) {
+ hsync_start /= 2;
+ hsync_end /= 2;
+ }
+
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ I915_WRITE(HSYNC(dsi_trans),
+ (hsync_start - 1) | ((hsync_end - 1) << 16));
+ }
+ }
+
+ /* program TRANS_VTOTAL register */
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ /*
+ * FIXME: Programing this by assuming progressive mode, since
+ * non-interlaced info from VBT is not saved inside
+ * struct drm_display_mode.
+ * For interlace mode: program required pixel minus 2
+ */
+ I915_WRITE(VTOTAL(dsi_trans),
+ (vactive - 1) | ((vtotal - 1) << 16));
+ }
+
+ if (vsync_end < vsync_start || vsync_end > vtotal)
+ DRM_ERROR("Invalid vsync_end value\n");
+
+ if (vsync_start < vactive)
+ DRM_ERROR("vsync_start less than vactive\n");
+
+ /* program TRANS_VSYNC register */
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ I915_WRITE(VSYNC(dsi_trans),
+ (vsync_start - 1) | ((vsync_end - 1) << 16));
+ }
+
+ /*
+ * FIXME: It has to be programmed only for interlaced
+ * modes. Put the check condition here once interlaced
+ * info available as described above.
+ * program TRANS_VSYNCSHIFT register
+ */
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ I915_WRITE(VSYNCSHIFT(dsi_trans), vsync_shift);
+ }
+}
+
+static void
gen11_dsi_enable_port_and_phy(struct intel_encoder *encoder,
const struct intel_crtc_state *pipe_config)
{
@@ -512,4 +627,7 @@ gen11_dsi_pre_enable(struct intel_encoder *encoder,
/* step4: enable DSI port and DPHY */
gen11_dsi_enable_port_and_phy(encoder, pipe_config);
+
+ /* step6c: configure transcoder timings */
+ gen11_dsi_set_transcoder_timings(encoder, pipe_config);
}
--
2.11.0
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
