On Tue, Jun 26, 2018 at 10:40:26AM -0700, Paulo Zanoni wrote:
> Em Seg, 2018-06-25 às 16:55 -0700, Souza, Jose escreveu:
> > On Thu, 2018-06-21 at 21:44 +0300, Imre Deak wrote:
> > > So far we got an AUX power domain reference only for the duration
> > > of
> > > DP
> > > AUX transfers. However, the following suggests that we also need
> > > these
> > > for main link functionality:
> > > - The specification doesn't state whether it's needed or not for
> > > main
> > > link functionality, but suggests that these power wells need to
> > > be
> > > enabled already during display core initialization (Sequences to
> > > Initialize Display).
>
> No, the specification states it's needed. Page "Sequences for
> DisplayPort" (the ICL version, of course), step 1.b:
>
> "TC: Note that AUX power is required for running main link."
>
> Same for the HDMI page.
Yes, for ICL MG PHY ports (in all modes) it's clearly stated as I also
wrote it below. The above is about the ICL combo PHY ports and the other
platforms. For those the only hint is that enabling the AUX power wells
is listed as a step in the 'Sequences to Initialize Display".
>
> > > - For PSR we need to keep the AUX power well enabled.
> > > - On ICL combo PHY ports (non-TC) the AUX power well is needed for
> > > link training too: while the port is enabled with a DP link
> > > training
> > > test pattern trying to toggle the AUX power well will time out.
> > > - On ICL MG PHY ports (TC) the AUX power well is needed also for
> > > main
> > > link functionality (both in DP and HDMI modes).
> > > - Windows enables these power wells both for main and AUX lane
> > > functionality.
> > >
> > > Based on the above take an AUX power reference for main link
> > > functionality too. This makes a difference only on GEN10+ (GLK+)
> > > platforms, where we have separate port specific AUX power wells.
> > >
> > > For PSR we still need to distinguish between port A and the other
> > > ports, since on port A DC states must stay enabled for main link
> > > functionality, but DC states must be disabled for driver initiated
> > > AUX transfers. So re-use the corresponding helper from intel_psr.c.
> > >
> > > Since we take now a reference for main link functionality on all DP
> > > ports we can forgo taking the separate power ref for PSR
> > > functionality.
> > >
> > > v2:
> > > - Make sure DC states stay enabled when taking the ref on port A.
> > > (Ville)
> > >
> > > v3: (Ville)
> > > - Fix comment about logic for encoders without a crtc state and
> > > add FIXME note for a simplification to avoid calling
> > > get_power_domains
> > > in such cases.
> > > - Use intel_crtc_has_dp_encoder() instead
> > > !intel_crtc_has_type(HDMI).
> > >
> > > Cc: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
> > > Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@xxxxxxxxx>
> > > Cc: Paulo Zanoni <paulo.r.zanoni@xxxxxxxxx>
> > > Signed-off-by: Imre Deak <imre.deak@xxxxxxxxx>
> >
> > The spec is not clear but this fix the "aux power well" enable
> > timeouts
> > that I was getting in aux B so looks like your interpretation is
> > right.
> >
> > Reviewed-by: José Roberto de Souza <jose.souza@xxxxxxxxx>
> >
> > > ---
> > > drivers/gpu/drm/i915/intel_ddi.c | 54
> > > ++++++++++++++++++++++++++++++---
> > > drivers/gpu/drm/i915/intel_display.c | 12 +++++++-
> > > drivers/gpu/drm/i915/intel_drv.h | 3 +-
> > > drivers/gpu/drm/i915/intel_psr.c | 41 ---------------------
> > > ----
> > > drivers/gpu/drm/i915/intel_runtime_pm.c | 1 +
> > > 5 files changed, 64 insertions(+), 47 deletions(-)
> > >
> > > diff --git a/drivers/gpu/drm/i915/intel_ddi.c
> > > b/drivers/gpu/drm/i915/intel_ddi.c
> > > index 044fe1fb9872..0319825b725b 100644
> > > --- a/drivers/gpu/drm/i915/intel_ddi.c
> > > +++ b/drivers/gpu/drm/i915/intel_ddi.c
> > > @@ -1983,15 +1983,55 @@ bool intel_ddi_get_hw_state(struct
> > > intel_encoder *encoder,
> > > return ret;
> > > }
> > >
> > > -static u64 intel_ddi_get_power_domains(struct intel_encoder
> > > *encoder)
> > > +static inline enum intel_display_power_domain
> > > +intel_ddi_main_link_aux_domain(struct intel_dp *intel_dp)
> > > +{
> > > + /* CNL HW requires corresponding AUX IOs to be powered up
> > > for PSR with
> > > + * DC states enabled at the same time, while for driver
> > > initiated AUX
> > > + * transfers we need the same AUX IOs to be powered but
> > > with
> > > DC states
> > > + * disabled. Accordingly use the AUX power domain here
> > > which
> > > leaves DC
> > > + * states enabled.
> > > + * However, for non-A AUX ports the corresponding non-EDP
> > > transcoders
> > > + * would have already enabled power well 2 and DC_OFF.
> > > This
> > > means we can
> > > + * acquire a wider POWER_DOMAIN_AUX_{B,C,D,F} reference
> > > instead of a
> > > + * specific AUX_IO reference without powering up any extra
> > > wells.
> > > + * Note that PSR is enabled only on Port A even though
> > > this
> > > function
> > > + * returns the correct domain for other ports too.
> > > + */
> > > + return intel_dp->aux_ch == AUX_CH_A ?
> > > POWER_DOMAIN_AUX_IO_A
> > > :
> > > + intel_dp-
> > > > aux_power_domain;
> > >
> > > +}
> > > +
> > > +static u64 intel_ddi_get_power_domains(struct intel_encoder
> > > *encoder,
> > > + struct intel_crtc_state
> > > *crtc_state)
> > > {
> > > struct intel_digital_port *dig_port =
> > > enc_to_dig_port(&encoder->base);
> > > enum pipe pipe;
> > > + u64 domains;
> > >
> > > - if (intel_ddi_get_hw_state(encoder, &pipe))
> > > - return BIT_ULL(dig_port->ddi_io_power_domain);
> > > + if (!intel_ddi_get_hw_state(encoder, &pipe))
> > > + return 0;
> > >
> > > - return 0;
> > > + domains = BIT_ULL(dig_port->ddi_io_power_domain);
> > > + if (!crtc_state)
> > > + return domains;
> > > +
> > > + /*
> > > + * TODO: Add support for MST encoders. Atm, the following
> > > should never
> > > + * happen since this function will be called only for the
> > > primary
> > > + * encoder which doesn't have its own pipe/crtc_state.
> > > + */
> > > + if (WARN_ON(intel_crtc_has_type(crtc_state,
> > > INTEL_OUTPUT_DP_MST)))
> > > + return domains;
> > > +
> > > + /* AUX power is only needed for (e)DP mode, not for HDMI.
> > > */
> > > + if (intel_crtc_has_dp_encoder(crtc_state)) {
> > > + struct intel_dp *intel_dp = &dig_port->dp;
> > > +
> > > + domains |=
> > > BIT_ULL(intel_ddi_main_link_aux_domain(intel_dp));
> > > + }
> > > +
> > > + return domains;
> > > }
> > >
> > > void intel_ddi_enable_pipe_clock(const struct intel_crtc_state
> > > *crtc_state)
> > > @@ -2631,6 +2671,9 @@ static void intel_ddi_pre_enable_dp(struct
> > > intel_encoder *encoder,
> > >
> > > WARN_ON(is_mst && (port == PORT_A || port == PORT_E));
> > >
> > > + intel_display_power_get(dev_priv,
> > > + intel_ddi_main_link_aux_domain(int
> > > el
> > > _dp));
> > > +
> > > intel_dp_set_link_params(intel_dp, crtc_state->port_clock,
> > > crtc_state->lane_count, is_mst);
> > >
> > > @@ -2775,6 +2818,9 @@ static void intel_ddi_post_disable_dp(struct
> > > intel_encoder *encoder,
> > > intel_display_power_put(dev_priv, dig_port-
> > > > ddi_io_power_domain);
> > >
> > >
> > > intel_ddi_clk_disable(encoder);
> > > +
> > > + intel_display_power_put(dev_priv,
> > > + intel_ddi_main_link_aux_domain(int
> > > el
> > > _dp));
> > > }
> > >
> > > static void intel_ddi_post_disable_hdmi(struct intel_encoder
> > > *encoder,
> > > diff --git a/drivers/gpu/drm/i915/intel_display.c
> > > b/drivers/gpu/drm/i915/intel_display.c
> > > index 2c8fef3ede54..ce615f89b43a 100644
> > > --- a/drivers/gpu/drm/i915/intel_display.c
> > > +++ b/drivers/gpu/drm/i915/intel_display.c
> > > @@ -15676,11 +15676,21 @@ get_encoder_power_domains(struct
> > > drm_i915_private *dev_priv)
> > > for_each_intel_encoder(&dev_priv->drm, encoder) {
> > > u64 get_domains;
> > > enum intel_display_power_domain domain;
> > > + struct intel_crtc_state *crtc_state;
> > >
> > > if (!encoder->get_power_domains)
> > > continue;
> > >
> > > - get_domains = encoder->get_power_domains(encoder);
> > > + /*
> > > + * For MST and inactive encoders we don't have a
> > > crtc state.
> > > + * FIXME: no need to call get_power_domains in
> > > such
> > > cases, it
> > > + * will always return 0.
> > > + */
> > > + crtc_state = encoder->base.crtc ?
> > > + to_intel_crtc_state(encoder-
> > > >base.crtc-
> > > > state) :
> > >
> > > + NULL;
> > > +
> > > + get_domains = encoder->get_power_domains(encoder,
> > > crtc_state);
> > > for_each_power_domain(domain, get_domains)
> > > intel_display_power_get(dev_priv, domain);
> > > }
> > > diff --git a/drivers/gpu/drm/i915/intel_drv.h
> > > b/drivers/gpu/drm/i915/intel_drv.h
> > > index 0c3ac0eafde0..7174429d930a 100644
> > > --- a/drivers/gpu/drm/i915/intel_drv.h
> > > +++ b/drivers/gpu/drm/i915/intel_drv.h
> > > @@ -254,7 +254,8 @@ struct intel_encoder {
> > > struct intel_crtc_state *pipe_config);
> > > /* Returns a mask of power domains that need to be
> > > referenced as part
> > > * of the hardware state readout code. */
> > > - u64 (*get_power_domains)(struct intel_encoder *encoder);
> > > + u64 (*get_power_domains)(struct intel_encoder *encoder,
> > > + struct intel_crtc_state
> > > *crtc_state);
> > > /*
> > > * Called during system suspend after all pending requests
> > > for the
> > > * encoder are flushed (for example for DP AUX
> > > transactions)
> > > and
> > > diff --git a/drivers/gpu/drm/i915/intel_psr.c
> > > b/drivers/gpu/drm/i915/intel_psr.c
> > > index d4cd19fea148..eecdd8b5b5e0 100644
> > > --- a/drivers/gpu/drm/i915/intel_psr.c
> > > +++ b/drivers/gpu/drm/i915/intel_psr.c
> > > @@ -56,43 +56,6 @@
> > > #include "intel_drv.h"
> > > #include "i915_drv.h"
> > >
> > > -static inline enum intel_display_power_domain
> > > -psr_aux_domain(struct intel_dp *intel_dp)
> > > -{
> > > - /* CNL HW requires corresponding AUX IOs to be powered up
> > > for PSR.
> > > - * However, for non-A AUX ports the corresponding non-EDP
> > > transcoders
> > > - * would have already enabled power well 2 and DC_OFF.
> > > This
> > > means we can
> > > - * acquire a wider POWER_DOMAIN_AUX_{B,C,D,F} reference
> > > instead of a
> > > - * specific AUX_IO reference without powering up any extra
> > > wells.
> > > - * Note that PSR is enabled only on Port A even though
> > > this
> > > function
> > > - * returns the correct domain for other ports too.
> > > - */
> > > - return intel_dp->aux_ch == AUX_CH_A ?
> > > POWER_DOMAIN_AUX_IO_A
> > > :
> > > - intel_dp-
> > > > aux_power_domain;
> > >
> > > -}
> > > -
> > > -static void psr_aux_io_power_get(struct intel_dp *intel_dp)
> > > -{
> > > - struct intel_digital_port *intel_dig_port =
> > > dp_to_dig_port(intel_dp);
> > > - struct drm_i915_private *dev_priv =
> > > to_i915(intel_dig_port-
> > > > base.base.dev);
> > >
> > > -
> > > - if (INTEL_GEN(dev_priv) < 10)
> > > - return;
> > > -
> > > - intel_display_power_get(dev_priv,
> > > psr_aux_domain(intel_dp));
> > > -}
> > > -
> > > -static void psr_aux_io_power_put(struct intel_dp *intel_dp)
> > > -{
> > > - struct intel_digital_port *intel_dig_port =
> > > dp_to_dig_port(intel_dp);
> > > - struct drm_i915_private *dev_priv =
> > > to_i915(intel_dig_port-
> > > > base.base.dev);
> > >
> > > -
> > > - if (INTEL_GEN(dev_priv) < 10)
> > > - return;
> > > -
> > > - intel_display_power_put(dev_priv,
> > > psr_aux_domain(intel_dp));
> > > -}
> > > -
> > > void intel_psr_irq_control(struct drm_i915_private *dev_priv, bool
> > > debug)
> > > {
> > > u32 debug_mask, mask;
> > > @@ -595,8 +558,6 @@ static void hsw_psr_enable_source(struct
> > > intel_dp
> > > *intel_dp,
> > > struct drm_i915_private *dev_priv = to_i915(dev);
> > > enum transcoder cpu_transcoder = crtc_state-
> > > >cpu_transcoder;
> > >
> > > - psr_aux_io_power_get(intel_dp);
> > > -
> > > /* Only HSW and BDW have PSR AUX registers that need to be
> > > setup. SKL+
> > > * use hardcoded values PSR AUX transactions
> > > */
> > > @@ -717,8 +678,6 @@ static void hsw_psr_disable(struct intel_dp
> > > *intel_dp,
> > > else
> > > WARN_ON(I915_READ(EDP_PSR_CTL) &
> > > EDP_PSR_ENABLE);
> > > }
> > > -
> > > - psr_aux_io_power_put(intel_dp);
> > > }
> > >
> > > /**
> > > diff --git a/drivers/gpu/drm/i915/intel_runtime_pm.c
> > > b/drivers/gpu/drm/i915/intel_runtime_pm.c
> > > index de3a81034f77..2969787201ef 100644
> > > --- a/drivers/gpu/drm/i915/intel_runtime_pm.c
> > > +++ b/drivers/gpu/drm/i915/intel_runtime_pm.c
> > > @@ -1824,6 +1824,7 @@ void intel_display_power_put(struct
> > > drm_i915_private *dev_priv,
> > > BIT_ULL(POWER_DOMAIN_INIT))
> > > #define GLK_DISPLAY_AUX_A_POWER_DOMAINS ( \
> > > BIT_ULL(POWER_DOMAIN_AUX_A) | \
> > > + BIT_ULL(POWER_DOMAIN_AUX_IO_A) | \
> > > BIT_ULL(POWER_DOMAIN_INIT))
> > > #define GLK_DISPLAY_AUX_B_POWER_DOMAINS ( \
> > > BIT_ULL(POWER_DOMAIN_AUX_B) | \
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
