On Thu, Jun 14, 2018 at 12:23:36PM -0700, Rodrigo Vivi wrote:
> On Thu, May 24, 2018 at 04:42:37PM -0700, Paulo Zanoni wrote:
> > From: Manasi Navare <manasi.d.navare@xxxxxxxxx>
> >
> > For ICL, on Combo PHY the allowed max rates are:
> > - HBR3 8.1 eDP (DDIA)
> > - HBR2 5.4 DisplayPort (DDIB)
> > and for MG PHY/TC DDI Ports allowed DP rates are:
> > - HBR3 8.1 DisplayPort (DP alternate mode, DP over TBT,
> > - DP on legacy connector - DDIC/D/E/F)
> >
> > Cc: Rodrigo Vivi <rodrigo.vivi@xxxxxxxxx>
> > Cc: Jani Nikula <jani.nikula@xxxxxxxxxxxxxxx>
> > Cc: James Ausmus <james.ausmus@xxxxxxxxx>
> > Signed-off-by: Manasi Navare <manasi.d.navare@xxxxxxxxx>
> > Signed-off-by: James Ausmus <james.ausmus@xxxxxxxxx>
> > ---
> > drivers/gpu/drm/i915/intel_dp.c | 21 +++++++++++++++++++--
> > 1 file changed, 19 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
> > index 5109023abe28..3ee8e74cf2b8 100644
> > --- a/drivers/gpu/drm/i915/intel_dp.c
> > +++ b/drivers/gpu/drm/i915/intel_dp.c
> > @@ -419,6 +419,20 @@ static int cnl_max_source_rate(struct intel_dp *intel_dp)
> > return 810000;
> > }
> >
> > +static int icl_max_source_rate(struct intel_dp *intel_dp)
> > +{
> > + struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
> > + enum port port = dig_port->base.port;
> > +
> > + /* On Combo PHY port A max speed is HBR3 for all Vccio voltages
> > + * and on Combo PHY Port B the maximum supported is HBR2.
> > + */
> > + if (port == PORT_B)
>
> A more generic way here would be COMBO and !eDP
Yes I can use the function intel_is_port_combophy() but I dont see that merged yet
Will have to wait to spin this patch in that case.
>
> > + return 540000;
> > +
> > + return 810000;
> > +}
> > +
> > static void
> > intel_dp_set_source_rates(struct intel_dp *intel_dp)
> > {
> > @@ -448,10 +462,13 @@ intel_dp_set_source_rates(struct intel_dp *intel_dp)
> > /* This should only be done once */
> > WARN_ON(intel_dp->source_rates || intel_dp->num_source_rates);
> >
> > - if (IS_CANNONLAKE(dev_priv)) {
> > + if (INTEL_GEN(dev_priv) >= 10) {
> > source_rates = cnl_rates;
> > size = ARRAY_SIZE(cnl_rates);
> > - max_rate = cnl_max_source_rate(intel_dp);
> > + if (IS_ICELAKE(dev_priv))
>
> and gen >= 11
>
> but changes can be in follow-up work, so
Yes will change that to use >= 11
Manasi
>
> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@xxxxxxxxx>
>
> > + max_rate = icl_max_source_rate(intel_dp);
> > + else
> > + max_rate = cnl_max_source_rate(intel_dp);
> > } else if (IS_GEN9_LP(dev_priv)) {
> > source_rates = bxt_rates;
> > size = ARRAY_SIZE(bxt_rates);
> > --
> > 2.14.3
> >
> > _______________________________________________
> > Intel-gfx mailing list
> > Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
> > https://lists.freedesktop.org/mailman/listinfo/intel-gfx
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
