Re: [PATCH v7 1/6] drm/i915: Fallback to lower link rate and lane count during link training

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Sep 26, 2016 at 04:39:34PM +0300, Jani Nikula wrote:
> On Fri, 16 Sep 2016, Manasi Navare <manasi.d.navare@xxxxxxxxx> wrote:
> > According to the DisplayPort Spec, in case of Clock Recovery failure
> > the link training sequence should fall back to the lower link rate
> > followed by lower lane count until CR succeeds.
> > On CR success, the sequence proceeds with Channel EQ.
> > In case of Channel EQ failures, it should fallback to
> > lower link rate and lane count and start the CR phase again.
> 
> This change makes the link training start at the max lane count and max
> link rate. This is not ideal, as it wastes the link. And it is not a
> spec requirement. "The Link Policy Maker of the upstream device may
> choose any link count and link rate as long as they do not exceed the
> capabilities of the DP receiver."
> 
> Our current code starts at the minimum required bandwidth for the mode,
> therefore we can't fall back to lower link rate and lane count without
> reducing the mode.
> 
> AFAICT this patch here makes it possible for the link bandwidth to drop
> below what is required for the mode. This is unacceptable.
> 
> BR,
> Jani.
> 
>

Thanks Jani for your review comments.
Yes in this change we start at the max link rate and lane count. This change was
made according to the design document discussions we had before strating this DP 
Redesign project. The main reason for starting at the maxlink rate and max lane
count was for ensuring proper behavior of DP MST. In case of DP MST, we want to
train the link at the maximum supported link rate/lane count based on an early/
upfront link training result so that we dont fail when we try to connect a
higher resolution monitor as a second monitor. This a trade off between wsting 
the link or higher power vs. needing to retrain for every monitor that requests
a higher BW in case of DP MST.
 
Actually this is also the reason for enabling upfront link training in the 
following patch where we train the link much ahead in the modeset sequence 
to understand the link rate and lane count values at which the link can be 
successfully trained and then the link training through modeset will always start
at the upfront values (maximum supported values of lane count and link rate based
on upfront link training).

As per the CTS, all the test 4.3.1.4 requires that you fall back to the lower link
rate after trying to train at the maximum link rate advertised through the DPCD 
registers.

This will not drop the link BW to a number below what is required for the mode 
because the requested modes are pruned or validated in intel_dp_mode_valid
based on the upfront link training results in the following patch. And these 
values are used here as the starting values of link rate and lane count.

I almost feel that the upfront link training patch and this patch should be 
combined so that insead of starting from the max link rate and lane count it
is clear that we are starting from the upfront values.

Regards,
Manasi 
> >
> > v7:
> > * Address readability concerns (Mika Kahola)
> > v6:
> > * Do not split quoted string across line (Mika Kahola)
> > v5:
> > * Reset the link rate index to the max link rate index
> > before lowering the lane count (Jani Nikula)
> > * Use the paradigm for loop in intel_dp_link_rate_index
> > v4:
> > * Fixed the link rate fallback loop (Manasi Navare)
> > v3:
> > * Fixed some rebase issues (Mika Kahola)
> > v2:
> > * Add a helper function to return index of requested link rate
> > into common_rates array
> > * Changed the link rate fallback loop to make use
> > of common_rates array (Mika Kahola)
> > * Changed INTEL_INFO to INTEL_GEN (David Weinehall)
> >
> > Signed-off-by: Manasi Navare <manasi.d.navare@xxxxxxxxx>
> > ---
> >  drivers/gpu/drm/i915/intel_ddi.c              | 113 +++++++++++++++++++++++---
> >  drivers/gpu/drm/i915/intel_dp.c               |  15 ++++
> >  drivers/gpu/drm/i915/intel_dp_link_training.c |  13 ++-
> >  drivers/gpu/drm/i915/intel_drv.h              |   6 +-
> >  4 files changed, 133 insertions(+), 14 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
> > index 8065a5f..093038c 100644
> > --- a/drivers/gpu/drm/i915/intel_ddi.c
> > +++ b/drivers/gpu/drm/i915/intel_ddi.c
> > @@ -1637,19 +1637,18 @@ void intel_ddi_clk_select(struct intel_encoder *encoder,
> >  	}
> >  }
> >  
> > -static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
> > +static void intel_ddi_pre_enable_edp(struct intel_encoder *encoder,
> >  				    int link_rate, uint32_t lane_count,
> > -				    struct intel_shared_dpll *pll,
> > -				    bool link_mst)
> > +				    struct intel_shared_dpll *pll)
> >  {
> >  	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
> >  	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> >  	enum port port = intel_ddi_get_encoder_port(encoder);
> >  
> >  	intel_dp_set_link_params(intel_dp, link_rate, lane_count,
> > -				 link_mst);
> > -	if (encoder->type == INTEL_OUTPUT_EDP)
> > -		intel_edp_panel_on(intel_dp);
> > +				 false);
> > +
> > +	intel_edp_panel_on(intel_dp);
> >  
> >  	intel_ddi_clk_select(encoder, pll);
> >  	intel_prepare_dp_ddi_buffers(encoder);
> > @@ -1660,6 +1659,28 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
> >  		intel_dp_stop_link_train(intel_dp);
> >  }
> >  
> > +static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
> > +				    int link_rate, uint32_t lane_count,
> > +				    struct intel_shared_dpll *pll,
> > +				    bool link_mst)
> > +{
> > +	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
> > +	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> > +	struct intel_shared_dpll_config tmp_pll_config;
> > +
> > +	/* Disable the PLL and obtain the PLL for Link Training
> > +	 * that starts with highest link rate and lane count.
> > +	 */
> > +	tmp_pll_config = pll->config;
> > +	pll->funcs.disable(dev_priv, pll);
> > +	pll->config.crtc_mask = 0;
> > +
> > +	/* If Link Training fails, send a uevent to generate a hotplug */
> > +	if (!intel_ddi_link_train(intel_dp, link_rate, lane_count, link_mst))
> > +		drm_kms_helper_hotplug_event(encoder->base.dev);
> > +	pll->config = tmp_pll_config;
> > +}
> > +
> >  static void intel_ddi_pre_enable_hdmi(struct intel_encoder *encoder,
> >  				      bool has_hdmi_sink,
> >  				      struct drm_display_mode *adjusted_mode,
> > @@ -1693,20 +1714,26 @@ static void intel_ddi_pre_enable(struct intel_encoder *intel_encoder,
> >  	struct intel_crtc *crtc = to_intel_crtc(encoder->crtc);
> >  	int type = intel_encoder->type;
> >  
> > -	if (type == INTEL_OUTPUT_DP || type == INTEL_OUTPUT_EDP) {
> > +	if (type == INTEL_OUTPUT_EDP)
> > +		intel_ddi_pre_enable_edp(intel_encoder,
> > +					crtc->config->port_clock,
> > +					crtc->config->lane_count,
> > +					crtc->config->shared_dpll);
> > +
> > +	if (type == INTEL_OUTPUT_DP)
> >  		intel_ddi_pre_enable_dp(intel_encoder,
> >  					crtc->config->port_clock,
> >  					crtc->config->lane_count,
> >  					crtc->config->shared_dpll,
> >  					intel_crtc_has_type(crtc->config,
> >  							    INTEL_OUTPUT_DP_MST));
> > -	}
> > -	if (type == INTEL_OUTPUT_HDMI) {
> > +
> > +	if (type == INTEL_OUTPUT_HDMI)
> >  		intel_ddi_pre_enable_hdmi(intel_encoder,
> >  					  crtc->config->has_hdmi_sink,
> >  					  &crtc->config->base.adjusted_mode,
> >  					  crtc->config->shared_dpll);
> > -	}
> > +
> >  }
> >  
> >  static void intel_ddi_post_disable(struct intel_encoder *intel_encoder,
> > @@ -2435,6 +2462,72 @@ intel_ddi_get_link_dpll(struct intel_dp *intel_dp, int clock)
> >  	return pll;
> >  }
> >  
> > +bool
> > +intel_ddi_link_train(struct intel_dp *intel_dp, int max_link_rate,
> > +		     uint8_t max_lane_count, bool link_mst)
> > +{
> > +	struct intel_connector *connector = intel_dp->attached_connector;
> > +	struct intel_encoder *encoder = connector->encoder;
> > +	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> > +	struct intel_shared_dpll *pll;
> > +	struct intel_shared_dpll_config tmp_pll_config;
> > +	int link_rate, max_link_rate_index, link_rate_index;
> > +	uint8_t lane_count;
> > +	int common_rates[DP_MAX_SUPPORTED_RATES] = {};
> > +	bool ret = false;
> > +
> > +	max_link_rate_index = intel_dp_link_rate_index(intel_dp, common_rates,
> > +						       max_link_rate);
> > +	if (max_link_rate_index < 0) {
> > +		DRM_ERROR("Invalid Link Rate\n");
> > +		return false;
> > +	}
> > +
> > +	for (lane_count = max_lane_count; lane_count > 0; lane_count >>= 1) {
> > +		for (link_rate_index = max_link_rate_index;
> > +		     link_rate_index >= 0; link_rate_index--) {
> > +			link_rate = common_rates[link_rate_index];
> > +			pll = intel_ddi_get_link_dpll(intel_dp, link_rate);
> > +			if (pll == NULL) {
> > +				DRM_ERROR("Could not find DPLL for link training.\n");
> > +				return false;
> > +			}
> > +			tmp_pll_config = pll->config;
> > +			pll->funcs.enable(dev_priv, pll);
> > +
> > +			intel_dp_set_link_params(intel_dp, link_rate,
> > +						 lane_count, link_mst);
> > +
> > +			intel_ddi_clk_select(encoder, pll);
> > +			intel_prepare_dp_ddi_buffers(encoder);
> > +			intel_ddi_init_dp_buf_reg(encoder);
> > +			intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
> > +			ret = intel_dp_start_link_train(intel_dp);
> > +			if (ret)
> > +				break;
> > +
> > +			/* Disable port followed by PLL for next
> > +			 *retry/clean up
> > +			 */
> > +			intel_ddi_post_disable(encoder, NULL, NULL);
> > +			pll->funcs.disable(dev_priv, pll);
> > +			pll->config = tmp_pll_config;
> > +		}
> > +		if (ret) {
> > +			DRM_DEBUG_KMS("Link Training successful at link rate: %d lane: %d\n",
> > +				      link_rate, lane_count);
> > +			break;
> > +		}
> > +	}
> > +
> > +	intel_dp_stop_link_train(intel_dp);
> > +
> > +	if (!lane_count)
> > +		DRM_ERROR("Link Training Failed\n");
> > +
> > +	return ret;
> > +}
> > +
> >  void intel_ddi_init(struct drm_device *dev, enum port port)
> >  {
> >  	struct drm_i915_private *dev_priv = to_i915(dev);
> > diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
> > index 69cee9b..d81c67cb 100644
> > --- a/drivers/gpu/drm/i915/intel_dp.c
> > +++ b/drivers/gpu/drm/i915/intel_dp.c
> > @@ -1506,6 +1506,21 @@ intel_dp_max_link_rate(struct intel_dp *intel_dp)
> >  	return rates[len - 1];
> >  }
> >  
> > +int intel_dp_link_rate_index(struct intel_dp *intel_dp, int *common_rates,
> > +			     int link_rate)
> > +{
> > +	int common_len;
> > +	int index;
> > +
> > +	common_len = intel_dp_common_rates(intel_dp, common_rates);
> > +	for (index = 0; index < common_len; index++) {
> > +		if (link_rate == common_rates[common_len - index - 1])
> > +			return common_len - index - 1;
> > +	}
> > +
> > +	return -1;
> > +}
> > +
> >  int intel_dp_rate_select(struct intel_dp *intel_dp, int rate)
> >  {
> >  	return rate_to_index(rate, intel_dp->sink_rates);
> > diff --git a/drivers/gpu/drm/i915/intel_dp_link_training.c b/drivers/gpu/drm/i915/intel_dp_link_training.c
> > index c438b02..6eb5eb6 100644
> > --- a/drivers/gpu/drm/i915/intel_dp_link_training.c
> > +++ b/drivers/gpu/drm/i915/intel_dp_link_training.c
> > @@ -313,9 +313,16 @@ void intel_dp_stop_link_train(struct intel_dp *intel_dp)
> >  				DP_TRAINING_PATTERN_DISABLE);
> >  }
> >  
> > -void
> > +bool
> >  intel_dp_start_link_train(struct intel_dp *intel_dp)
> >  {
> > -	intel_dp_link_training_clock_recovery(intel_dp);
> > -	intel_dp_link_training_channel_equalization(intel_dp);
> > +	bool ret;
> > +
> > +	if (intel_dp_link_training_clock_recovery(intel_dp)) {
> > +		ret = intel_dp_link_training_channel_equalization(intel_dp);
> > +		if (ret)
> > +			return true;
> > +	}
> > +
> > +	return false;
> >  }
> > diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
> > index 8fd16ad..08cb571 100644
> > --- a/drivers/gpu/drm/i915/intel_drv.h
> > +++ b/drivers/gpu/drm/i915/intel_drv.h
> > @@ -1164,6 +1164,8 @@ void intel_ddi_clock_get(struct intel_encoder *encoder,
> >  			 struct intel_crtc_state *pipe_config);
> >  void intel_ddi_set_vc_payload_alloc(struct drm_crtc *crtc, bool state);
> >  uint32_t ddi_signal_levels(struct intel_dp *intel_dp);
> > +bool intel_ddi_link_train(struct intel_dp *intel_dp, int max_link_rate,
> > +			  uint8_t max_lane_count, bool link_mst);
> >  struct intel_shared_dpll *intel_ddi_get_link_dpll(struct intel_dp *intel_dp,
> >  						  int clock);
> >  unsigned int intel_fb_align_height(struct drm_device *dev,
> > @@ -1385,7 +1387,7 @@ bool intel_dp_init_connector(struct intel_digital_port *intel_dig_port,
> >  void intel_dp_set_link_params(struct intel_dp *intel_dp,
> >  			      int link_rate, uint8_t lane_count,
> >  			      bool link_mst);
> > -void intel_dp_start_link_train(struct intel_dp *intel_dp);
> > +bool intel_dp_start_link_train(struct intel_dp *intel_dp);
> >  void intel_dp_stop_link_train(struct intel_dp *intel_dp);
> >  void intel_dp_sink_dpms(struct intel_dp *intel_dp, int mode);
> >  void intel_dp_encoder_reset(struct drm_encoder *encoder);
> > @@ -1407,6 +1409,8 @@ void intel_dp_add_properties(struct intel_dp *intel_dp, struct drm_connector *co
> >  void intel_dp_mst_suspend(struct drm_device *dev);
> >  void intel_dp_mst_resume(struct drm_device *dev);
> >  int intel_dp_max_link_rate(struct intel_dp *intel_dp);
> > +int intel_dp_link_rate_index(struct intel_dp *intel_dp, int *common_rates,
> > +			     int link_rate);
> >  int intel_dp_rate_select(struct intel_dp *intel_dp, int rate);
> >  void intel_dp_hot_plug(struct intel_encoder *intel_encoder);
> >  void intel_power_sequencer_reset(struct drm_i915_private *dev_priv);
> 
> -- 
> Jani Nikula, Intel Open Source Technology Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx




[Index of Archives]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]
  Powered by Linux