|
Hi mate,
I think (and say think :) )I finally found a method. Although I'm testing it deeply... it seems (say seems too :) ) 2.4 is compatible with a mail spool in 2.3 (at least with my config). So I'll try to upgrade first to 2.4 and later to 3.0 setting up a replication from 2.4 to 3.0. Would be fine if Bron, Ellie or someone at Fastmail could tell something about it to us :) :)
Cheers!
---
Egoitz Aurrekoetxea
Departamento de sistemas
944 209 470
Parque Tecnológico. Edificio 103
48170 Zamudio (Bizkaia)
Antes de imprimir este correo electrónico piense si es necesario hacerlo.
El 16-12-2018 22:24, John Capo escribió:
On Thu, December 13, 2018 13:25, Egoitz Aurrekoetxea wrote:
Hi again!
Else as a simplication way can you replicate any manner a 2.3 with some
newer version?. At least in manual mode (not rolling)?.
The replication protocol in 2.4 is not compatible wit 2.3. There is no easy way. I'm rsync'ing one account at a time between 2.3 and 2.4 with IMAP/POP and LMTP access disabled, followed by a reconstruct, and then enabling IMAP/POP and LMTP access. Many terrabytes to go. You could also look at imapsync but its slow.
Cheers.
---
EGOITZ AURREKOETXEA
Departamento de sistemas
944 209 470
Parque Tecnológico. Edificio 103
48170 Zamudio (Bizkaia)
egoitz@xxxxxxxxxx www.sarenet.es [1] Antes de imprimir este correo electrónico piense si es
necesario hacerlo.
El 13-12-2018 16:52, Egoitz Aurrekoetxea escribió:
Good afternoon,
I was trying to upgrade part of our Cyrus imap installation, concretely that one consisting in
still 2.3. I was planning to set up Cyrus 3.0. I have seen all works properly except for the
unexpunge command because as someone stated here, a reconstruct -V max was needed.The problem
is that this reconstruct command, takes ages and I'm not able to keep the service offline so
many time. So I have been thinking in the following scenario :
- Cyrus 2.3 master -> Cyrus 2.4 slave
Get this 2.4 slave ready and set it as master. But here comes my first doubt. Does the 2.4
replication work with the 2.3 replication?. Can in this pair, both (the 2.3 and the 2.4) be
both master and slave?. I mean to switch roles in the pair. Make one become master and the
other slave and vice versa?.
Let's think now Cyrus 2.4 is ready and working.
- Now, I would set up a new 3.0 slave. I know 2.4 could replicate with 3.0. So I would get the
3.0 ready and then set 3.0 as master. Can in this pair both the 2.4 and 3.0 be master and
slave?. Meaning again to the same role switching commented before... to make one to be master
and the other slave or vice versa....
I'l will end up with 2 3.0 master and slave... but I need to trace the path...
Does anyone see any other way?.
Best regards,
-
--
EGOITZ AURREKOETXEA
Departamento de sistemas
944 209 470
Parque Tecnológico. Edificio 103
48170 Zamudio (Bizkaia)
egoitz@xxxxxxxxxx www.sarenet.es [1] Antes de imprimir este correo electrónico piense si es
necesario hacerlo. ----
Cyrus Home Page: http://www.cyrusimap.org/
List Archives/Info: http://lists.andrew.cmu.edu/pipermail/info-cyrus/
To Unsubscribe:
https://lists.andrew.cmu.edu/mailman/listinfo/info-cyrus
Links:
------
[1] http://www.sarenet.es
|
----
Cyrus Home Page: http://www.cyrusimap.org/
List Archives/Info: http://lists.andrew.cmu.edu/pipermail/info-cyrus/
To Unsubscribe:
https://lists.andrew.cmu.edu/mailman/listinfo/info-cyrus
