I have a user with AR9285 who was able to associate with and use an open network
(WHU-STU in the list below).
% ifconfig wlan0 scan
SSID/MESH ID BSSID CHAN RATE S:N INT CAPS
WHU-STU 70:d9:31:0e:5e:20 1 54M -81:-96 300 ES HTCAP WME ATH
CU_3n2r 80:ee:25:a7:af:c8 6 54M -93:-96 100 EP RSN WPS HTCAP WME BSSLOAD
HUAWEI-4QGNEY 5c:03:39:dd:2e:7c 11 54M -87:-96 100 EPS HTCAP WME ATH WPS RSN
WHU-STU 70:d9:31:03:06:40 13 54M -92:-96 300 ES HTCAP WME ATH
WHU-STU 70:d9:31:03:19:e0 13 54M -93:-96 300 ES HTCAP WME ATH
Xiaomi_102 50:d2:f5:87:7a:5a 2 54M -91:-96 100 EP APCHANREP APCHANREP WPA RSN WPS HTCAP WME BSSLOAD
ChinaNet-r6xR ec:f0:fe:71:ea:53 3 54M -93:-96 100 EPS WPA RSN HTCAP WME BSSLOAD
ChinaNet-wqSx 6c:d2:ba:94:73:d3 4 54M -93:-96 100 EPS WPA RSN HTCAP WME BSSLOAD
WHU-STU fc:b6:98:f5:cc:00 5 54M -85:-96 300 ES HTCAP WME ATH
WHU-STU 70:d9:31:0e:2c:00 5 54M -73:-96 300 ES HTCAP WME ATH # <-------- the one supposed to work
WHU-STU 70:d9:31:0e:19:20 5 54M -86:-96 300 ES HTCAP WME ATH
WHU-STU fc:b6:98:f6:01:a0 5 54M -88:-96 300 ES HTCAP WME ATH
WHU-STU 70:d9:31:0e:1b:e0 5 54M -94:-96 300 ES HTCAP WME ATH
CMCC-UKg3 14:ad:ca:ce:ea:fe 8 54M -94:-96 100 EPS APCHANREP APCHANREP WPA RSN HTCAP WME BSSLOAD
WHU-STU fc:b6:98:f6:0a:20 9 54M -81:-95 300 ES HTCAP WME ATH
WHU-STU 70:d9:31:12:9b:80 9 54M -85:-95 300 ES HTCAP WME ATH
WHU-STU fc:b6:98:f5:cc:80 9 54M -85:-95 300 ES HTCAP WME ATH
WHU-STU fc:b6:98:f6:22:80 9 54M -92:-95 300 ES HTCAP WME ATH
When using wpa_supplicant 2.9 they are able to associate and dhclient is able to
obtain an IP address:
wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 1c:4b:d6:ca:3e:ac
inet 10.134.135.167/17 broadcast 10.134.255.255
groups: wlan
ssid WHU-STU channel 13 (2472 MHz 11g ht/20) bssid fc:b6:98:f6:12:80
regdomain 96 indoor ecm authmode OPEN privacy OFF txpower 20 bmiss 7
scanvalid 60 protmode CTS ampdulimit 64k shortgi -stbctx stbcrx -ldpc
-uapsd wme burst roaming MANUAL bintval 300
parent interface: ath0
media: IEEE 802.11 Wireless Ethernet MCS mode 11ng
status: associated
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
However using wpa_supplicant 2.10 they associate 50% of the time but 100% of the
time are unable to communicate with the AP:
wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 1c:4b:d6:ca:3e:ac
inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
groups: wlan
ssid WHU-STU channel 5 (2432 MHz 11g ht/20) bssid 70:d9:31:0e:2c:00
regdomain 96 indoor ecm authmode WPA privacy MIXED deftxkey UNDEF
txpower 20 bmiss 7 scanvalid 60 protmode CTS ampdulimit 64k shortgi
-stbctx stbcrx -ldpc -uapsd wme burst roaming MANUAL bintval 300
parent interface: ath0
media: IEEE 802.11 Wireless Ethernet DS/1Mbps mode 11ng
status: associated
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
Wpa_supplicant 2.10 configures the device with:
authmode WPA privacy MIXED deftxkey UNDEF
While with wpa_supplicant 2.9 the following are correctly set:
authmode OPEN privacy OFF
It appears that wpa_supplicant has configured WPA even though the following are in wpa_supplicant.conf.
network={
ssid="WHU-STU"
key_mgmt=NONE
}
The same drivers are in use.
What am I missing? Or is there something else going on?
--
Cheers,
Cy Schubert <Cy.Schubert@xxxxxxxxxxxxx>
FreeBSD UNIX: <cy@xxxxxxxxxxx> Web: http://www.FreeBSD.org
NTP: <cy@xxxxxxxxxx> Web: https://nwtime.org
e**(i*pi)+1=0
_______________________________________________
Hostap mailing list
Hostap@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/hostap
