Not sure if this is the right place to ask a user question. My Qualcomm Atheros ar9462 is not sending my ssid when I start hostapd and I get no errors. The kernel loads the ath9k driver and iw list shows. I can scan an see local ssid, but I can't make AP mode work. Thanks, Supported interface modes: * IBSS * managed * AP * AP/VLAN * monitor * mesh point * P2P-client * P2P-GO * outside context of a BSS Capabilities: 0x11ef RX LDPC HT20/HT40 SM Power Save disabled RX HT20 SGI RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Frequencies: * 5180 MHz [36] (18.0 dBm) (no IR) * 5200 MHz [40] (18.0 dBm) (no IR) * 5220 MHz [44] (18.0 dBm) (no IR) * 5240 MHz [48] (18.0 dBm) (no IR) * 5260 MHz [52] (18.0 dBm) (no IR, radar detection) * 5280 MHz [56] (18.0 dBm) (no IR, radar detection) * 5300 MHz [60] (18.0 dBm) (no IR, radar detection) * 5320 MHz [64] (18.0 dBm) (no IR, radar detection) * 5500 MHz [100] (18.0 dBm) (no IR, radar detection) * 5520 MHz [104] (18.0 dBm) (no IR, radar detection) * 5540 MHz [108] (18.0 dBm) (no IR, radar detection) * 5560 MHz [112] (18.0 dBm) (no IR, radar detection) * 5580 MHz [116] (18.0 dBm) (no IR, radar detection) * 5600 MHz [120] (18.0 dBm) (no IR, radar detection) * 5620 MHz [124] (18.0 dBm) (no IR, radar detection) * 5640 MHz [128] (18.0 dBm) (no IR, radar detection) * 5660 MHz [132] (18.0 dBm) (no IR, radar detection) * 5680 MHz [136] (18.0 dBm) (no IR, radar detection) * 5700 MHz [140] (18.0 dBm) (no IR, radar detection) * 5745 MHz [149] (18.0 dBm) * 5765 MHz [153] (18.0 dBm) (no IR) * 5785 MHz [157] (18.0 dBm) (no IR) * 5805 MHz [161] (18.0 dBm) (no IR) * 5825 MHz [165] (18.0 dBm) (no IR) $hostapd.conf interface=wlp3s0 bridge=br0 driver=nl80211 ctrl_interface=/var/run/hostapd ctrl_interface_group=wheel ssid=<ssid_name> country_code=US hw_mode=a channel=149 macaddr_acl=1 accept_mac_file=/etc/hostapd/hostapd.accept auth_algs=1 ignore_broadcast_ssid=0 wmm_enabled=1 ieee80211n=1 ht_capab=[HT40+][SHORT-GI-40][DSSS_CCK-40] wpa=2 wpa_key_mgmt=WPA-PSK rsn_pairwise=CCMP wpa_passphrase=<passphrase> _______________________________________________ Hostap mailing list Hostap@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/hostap
