I'm trying to configure hostapd, but the SSID doesn't appear. This is the case with Debian 10, OpenSUSE 15.1, and 2.9 from the website. If I use dd-wrt on the same hardware, I am able to see an SSID on other devices. lspci reports the nic as: 04:00.0 Network controller: Qualcomm Atheros AR928X Wireless Network Adapter (PCI-Express) (rev 01) My minimal config: interface=wlan0 driver=nl80211 ssid=test ctrl_interface=/var/run/hostapd channel=1 wpa_key_mgmt=WPA-PSK Output from running with -dd: random: Trying to read entropy from /dev/random Configuration file: minimal_hostapd.conf nl80211: TDLS supported nl80211: TDLS external setup nl80211: Supported cipher 00-0f-ac:1 nl80211: Supported cipher 00-0f-ac:5 nl80211: Supported cipher 00-0f-ac:2 nl80211: Supported cipher 00-0f-ac:4 nl80211: Supported cipher 00-0f-ac:10 nl80211: Supported cipher 00-0f-ac:8 nl80211: Supported cipher 00-0f-ac:9 nl80211: Supported cipher 00-0f-ac:6 nl80211: Supported cipher 00-0f-ac:13 nl80211: Supported cipher 00-0f-ac:11 nl80211: Supported cipher 00-0f-ac:12 nl80211: Using driver-based off-channel TX nl80211: Driver-advertised extended capabilities (default) - hexdump(len=8): 00 00 00 00 00 00 00 40 nl80211: Driver-advertised extended capabilities mask (default) - hexdump(len=8): 00 00 00 00 00 00 00 40 nl80211: Use separate P2P group interface (driver advertised support) nl80211: interface wlan0 in phy phy0 nl80211: Set mode ifindex 5 iftype 3 (AP) nl80211: Setup AP(wlan0) - device_ap_sme=0 use_monitor=0 nl80211: Subscribe to mgmt frames with AP handle 0x12b52a0 nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x12b52a0 match= nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ) nl_handle=0x12b52a0 match= nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ) nl_handle=0x12b52a0 match= nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC) nl_handle=0x12b52a0 match= nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH) nl_handle=0x12b52a0 match= nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0x12b52a0 match= nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x12b52a0 match=04 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x12b52a0 match=0501 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x12b52a0 match=0503 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x12b52a0 match=0504 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x12b52a0 match=06 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x12b52a0 match=08 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x12b52a0 match=09 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x12b52a0 match=0a nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x12b52a0 match=11 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x12b52a0 match=7f rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 nl80211: Add own interface ifindex 5 (ifidx_reason -1) nl80211: if_indices[16]: 5(-1) phy: phy0 BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) nl80211: Regulatory information - country=US (DFS-FCC) nl80211: 2402-2472 @ 40 MHz 30 mBm nl80211: 5170-5250 @ 80 MHz 23 mBm nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS) nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS) nl80211: 5735-5835 @ 80 MHz 30 mBm nl80211: 57240-71000 @ 2160 MHz 40 mBm nl80211: Added 802.11b mode based on 802.11g information nl80211: Mode IEEE 802.11g: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467[DISABLED] 2472[DISABLED] 2484[DISABLED] nl80211: Mode IEEE 802.11a: 5180 5200 5220 5240 5260[NO_IR][RADAR] 5280[NO_IR] [RADAR] 5300[NO_IR][RADAR] 5320[NO_IR][RADAR] 5500[NO_IR][RADAR] 5520[NO_IR] [RADAR] 5540[NO_IR][RADAR] 5560[NO_IR][RADAR] 5580[NO_IR][RADAR] nl80211: Mode IEEE 802.11b: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467[DISABLED] 2472[DISABLED] 2484[DISABLED] Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=30 dBm Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=30 dBm Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=30 dBm Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=30 dBm Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=30 dBm Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=30 dBm Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=30 dBm Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=30 dBm Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=30 dBm Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=30 dBm Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=30 dBm Allowed channel: mode=2 chan=36 freq=5180 MHz max_tx_power=23 dBm Allowed channel: mode=2 chan=40 freq=5200 MHz max_tx_power=23 dBm Allowed channel: mode=2 chan=44 freq=5220 MHz max_tx_power=23 dBm Allowed channel: mode=2 chan=48 freq=5240 MHz max_tx_power=23 dBm Allowed channel: mode=2 chan=149 freq=5745 MHz max_tx_power=30 dBm Allowed channel: mode=2 chan=153 freq=5765 MHz max_tx_power=30 dBm Allowed channel: mode=2 chan=157 freq=5785 MHz max_tx_power=30 dBm Allowed channel: mode=2 chan=161 freq=5805 MHz max_tx_power=30 dBm Allowed channel: mode=2 chan=165 freq=5825 MHz max_tx_power=30 dBm Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=30 dBm Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=30 dBm Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=30 dBm Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=30 dBm Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=30 dBm Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=30 dBm Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=30 dBm Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=30 dBm Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=30 dBm Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=30 dBm Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=30 dBm Completing interface initialization Mode: IEEE 802.11b Channel: 1 Frequency: 2412 MHz DFS 0 channels required radar detection nl80211: Set freq 2412 (ht_enabled=0, vht_enabled=0, he_enabled=0, bandwidth=20 MHz, cf1=2412 MHz, cf2=0 MHz) * freq=2412 * he_enabled=0 * vht_enabled=0 * ht_enabled=0 * channel_type=0 RATE[0] rate=10 flags=0x1 RATE[1] rate=20 flags=0x1 RATE[2] rate=55 flags=0x0 RATE[3] rate=110 flags=0x0 hostapd_setup_bss(hapd=0x12d1bb0 (wlan0), first=1) wlan0: Flushing old station entries nl80211: flush -> DEL_STATION wlan0 (all) wlan0: Deauthenticate all stations nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3 nl80211: send_mlme -> send_frame nl80211: send_frame - Use bss->freq=2412 nl80211: send_frame -> send_frame_cmd nl80211: CMD_FRAME freq=2412 wait=0 no_cck=0 no_ack=0 offchanok=0 CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff 04 f0 21 45 82 7f 04 f0 21 45 82 7f 00 00 02 00 nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2412 wait=0) wpa_driver_nl80211_set_key: ifindex=5 (wlan0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=5 (wlan0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=5 (wlan0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=5 (wlan0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0 Using interface wlan0 with hwaddr 04:f0:21:45:82:7f and ssid "test" nl80211: Set beacon (beacon_set=0) nl80211: Beacon head - hexdump(len=51): 80 00 00 00 ff ff ff ff ff ff 04 f0 21 45 82 7f 04 f0 21 45 82 7f 00 00 00 00 00 00 00 00 00 00 64 00 01 00 00 04 74 65 73 74 01 04 82 84 0b 16 03 01 01 nl80211: Beacon tail - hexdump(len=14): 3b 02 51 00 7f 08 04 00 00 00 00 00 00 40 nl80211: ifindex=5 nl80211: beacon_int=100 nl80211: beacon_rate=0 nl80211: rate_type=0 nl80211: dtim_period=2 nl80211: ssid=test * beacon_int=100 * dtim_period=2 nl80211: hidden SSID not in use nl80211: privacy=0 nl80211: auth_algs=0x3 nl80211: wpa_version=0x0 nl80211: key_mgmt_suites=0x4 nl80211: pairwise_ciphers=0x0 nl80211: group_cipher=0x1 nl80211: beacon_ies - hexdump(len=10): 7f 08 04 00 00 00 00 00 00 40 nl80211: proberesp_ies - hexdump(len=10): 7f 08 04 00 00 00 00 00 00 40 nl80211: assocresp_ies - hexdump(len=10): 7f 08 04 00 00 00 00 00 00 40 nl80211: multicast to unicast disabled on interface wlan0 nl80211: Set wlan0 operstate 0->1 (UP) netlink: Operstate: ifindex=5 linkmode=-1 (no change), operstate=6 (IF_OPER_UP) nl80211: TX queue param set: queue=0 aifs=1 cw_min=3 cw_max=7 burst_time=15 -- > res=0 nl80211: TX queue param set: queue=1 aifs=1 cw_min=7 cw_max=15 burst_time=30 --> res=0 nl80211: TX queue param set: queue=2 aifs=3 cw_min=15 cw_max=63 burst_time=0 --> res=0 nl80211: TX queue param set: queue=3 aifs=7 cw_min=15 cw_max=1023 burst_time=0 --> res=0 wlan0: interface state UNINITIALIZED->ENABLED wlan0: AP-ENABLED wlan0: Setup of interface done. ctrl_iface not configured! random: Got 20/20 bytes from /dev/random RTM_NEWLINK: ifi_index=5 ifname=wlan0 operstate=2 linkmode=0 ifi_family=0 ifi_flags=0x1003 ([UP]) RTM_NEWLINK: ifi_index=5 ifname=wlan0 operstate=6 linkmode=0 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) Ip addr show produces: 5: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000 link/ether 04:f0:21:45:82:7f brd ff:ff:ff:ff:ff:ff inet6 fe80::6f0:21ff:fe45:827f/64 scope link valid_lft forever preferred_lft forever iwconfig wlan0 produces: wlan0 IEEE 802.11 Mode:Master Tx-Power=20 dBm Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Regards, Mark Gannon
Attachment:
signature.asc
Description: This is a digitally signed message part.
_______________________________________________ Hostap mailing list Hostap@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/hostap
