On 3/19/24 17:38, Michael Walle wrote:
On Tue Mar 19, 2024 at 12:36 PM CET, Ayush Singh wrote:Regardless, this patch actually does not contain any code for EEPROM support I have just mentioned it to give more context on why mikroBUS manifest is the focus of this patch instead of DT overlay or something else.Right, and I think this is the crux here. Why can't you use DT overlays? The manifest files, seem to be yet another hardware description (method) and we already have DT. Can't we have some kind of userspace helper that could translate them to DT overlays? That way, you could also handle the EEPROM vs non-EEPROM case, or have some other kind of method to load a DT overlay. Admittedly, I've never worked with in-kernel overlays, but AFAIK they work with some subsystems. -michaelSo let me 1st go over 3 cases that the driver needs to support: 1. Non EEPROM boards: Using overlays should be pretty similar to current solution. If the manifest is converted to overlay in userspace, then we do not even need to do manifest parsing, setting up spi, i2c etc in the kernel driver. 2. EEPROM boards How do you propose handling these. If you are proposing storing dt overlay in EEPROM, then this raises some questions regarding support outside of Linux. The other option would be generating overlay from manifest in the kernel driver, which I'm not sure is significantly better than registering the i2c, spi, etc. interfaces separately using standard kernel APIs.You did answer that yourself in (1): you could use a user space helper to translate it to a DT overlay, I don't think this has to be done in the kernel.
I do not understand what you mean. For EEPROM supported boards, user space is not involved. The driver can directly read the manifest from add-on board and setup everything, so it is plug and play.
The manual involvement of user space is only for non EEPROM boards since we do not have a way to identify the board without the user needing to provide the manifest.
Also how do you know whether there is an EEPROM or not?
Set RST GPIO to low. clickID supported board will enter ID MODE, Then check if CS line has a w1 gpio bus.
3. Over Greybus It is quite important to have mikroBUS over greybus for BeagleConnect. This is one of the major reasons why greybus manifest was chosen for the manifest format. Also, it is important to note that mikroBUS manifest is being used since 2020 now and thus manifests for a lot of boards (both supporting clickID and not supporting it exist). So I would prefer using it, unless of course there are strong reasons not to.And also here, I'm not really familiar with greybus. Could you give a more complex example? My concern is that some driver might need additional properties from DT (or software nodes) to function properly. It might not only be a node with a compatible string but also more advanced bindings. How would that play together with this? My gut feeling is that you can handle any missing properties easier/better (eg. for existing modules) in user space. But maybe that is already solved in/with greybus?
Greybus is a communication protocol designed for modular electronic devices. It allows different parts of a device to be hot plugged (added or removed) while the device is still running. Greybus manifest is used to describe the capabilities of a module in the greybus network. The host then creates appropriate bidirectional unipro connections with the module based on the cports described in the manifest. I have added a link to lwn article that goes into more detail.
BeagleConnect simply allows using greybus over any bidirectional transport, instead of just Unipro.
I cannot comment much about how greybus handles missing properties. While greybus also works just in kernel space, greybus protocols are inherently higher level than kernel driver, so it might have an easier time with this.
I have also added a link to eLInux page which provides rational for the mikroBUS manifest. But the crux seems to be that dynamic overlays were not well-supported back then. Also, the use of mikroBUS using greybus subsystem was already used. Hence the mikroBUS driver.
Greybus is not a big blocker from my perspective, since it is always possible to introduce a new protocol for mikroBUS in Greybus spec. I think as long as both EEPROM and non EEPROM boards can be supported by mikroBUS driver and dt-bindings, are can be used outside of Linux (eg: ZephyrRTOS, nuttx, etc), it is fine.
Here's a random one: the manifest [1] just lists the compatible string apparently, but the actual DT binding has also reset-gpios, some -supply and interrupt properties. -michael [1] https://github.com/MikroElektronika/click_id/blob/main/manifests/WEATHER-CLICK.mnfs
Yes, the concern is valid. Support for validating the manifest is nowhere near as good as devicetree overlays. But I think that would be a problem with the device rather than the responsibility of the kernel. It is up to the manufacturer to have valid manifests.
Link: https://lwn.net/Articles/715955/ Greybus Link https://elinux.org/Mikrobus eLinux article Ayush Singh _______________________________________________ greybus-dev mailing list -- greybus-dev@xxxxxxxxxxxxxxxx To unsubscribe send an email to greybus-dev-leave@xxxxxxxxxxxxxxxx
|