Re: [PATCH v4 1/5] dt-bindings: misc: Add mikrobus-connector

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun Mar 17, 2024 at 8:37 PM CET, Ayush Singh wrote:
> Add DT bindings for mikroBUS interface. MikroBUS is an open standard
> developed by MikroElektronika for connecting add-on boards to
> microcontrollers or microprocessors.
>
> mikroBUS is a connector and does not have a controller. Instead the
> software is responsible for identification of board and setting up /
> registering uart, spi, i2c, pwm and other buses. Thus it needs a way to
> get uart, spi, i2c, pwm and gpio controllers / adapters.
>
> A mikroBUS addon board is free to leave some of the pins unused which
> are marked as NC or Not Connected.
>
> Some of the pins might need to be configured as GPIOs deviating from their
> reserved purposes Eg: SHT15 Click where the SCL and SDA Pins need to be
> configured as GPIOs for the driver (drivers/hwmon/sht15.c) to work.
>
> For some add-on boards the driver may not take care of some additional
> signals like reset/wake-up/other. Eg: ENC28J60 click where the reset line
> (RST pin on the mikrobus port) needs to be pulled high.
>
> Here's the list of pins in mikroBUS connector:
> Analog - AN
> Reset - RST
> SPI Chip Select - CS
> SPI Clock - SCK
> SPI Master Input Slave Output - MISO
> SPI Master Output Slave Input - MOSI
> VCC-3.3V power - +3.3V
> Reference Ground - GND
> PWM - PWM output
> INT - Hardware Interrupt
> RX - UART Receive
> TX - UART Transmit
> SCL - I2C Clock
> SDA - I2C Data
> +5V - VCC-5V power
> GND - Reference Ground
>
> Additionally, some new mikroBUS boards contain 1-wire EEPROM that contains
> a manifest to describe the addon board to provide plug and play
> capabilities.
>
> Link: https://www.mikroe.com/mikrobus
> Link:
> https://download.mikroe.com/documents/standards/mikrobus/mikrobus-standard-specification-v200.pdf
> mikroBUS specification
> Link: https://www.mikroe.com/sht1x-click SHT15 Click
> Link: https://www.mikroe.com/eth-click ENC28J60 Click
> Link: https://www.mikroe.com/clickid ClickID
>
> Co-developed-by: Vaishnav M A <vaishnav@xxxxxxxxxxxxxxx>
> Signed-off-by: Vaishnav M A <vaishnav@xxxxxxxxxxxxxxx>
> Signed-off-by: Ayush Singh <ayushdevel1325@xxxxxxxxx>
> ---
>  .../connector/mikrobus-connector.yaml         | 113 ++++++++++++++++++

See also
https://lore.kernel.org/r/YmFo+EntwxIsco%2Ft@xxxxxxxxxxxxxxxxxx/

Looks like this proposal doesn't have the subnodes. How do you
attach a kernel driver to it's spi port for example? Only through
the manifest files?

-michael

Attachment: signature.asc
Description: PGP signature

_______________________________________________
greybus-dev mailing list -- greybus-dev@xxxxxxxxxxxxxxxx
To unsubscribe send an email to greybus-dev-leave@xxxxxxxxxxxxxxxx

[Index of Archives]     [Asterisk App Development]     [PJ SIP]     [Gnu Gatekeeper]     [IETF Sipping]     [Info Cyrus]     [ALSA User]     [Fedora Linux Users]     [Linux SCTP]     [DCCP]     [Gimp]     [Yosemite News]     [Deep Creek Hot Springs]     [Yosemite Campsites]     [ISDN Cause Codes]     [Asterisk Books]

  Powered by Linux