On Fri, Jan 11, 2019 at 09:41:34AM +0100, Johan Hovold wrote:
> On Thu, Jan 10, 2019 at 11:21:04PM +0530, Nishad Kamdar wrote:
> > Use the gpiod interface instead of the deprecated old non-descriptor
> > interface while continuing to ignore gpio flags from device tree in
> > functions "deassert_reset()" and "assert_reset()" for now.
> >
> > Signed-off-by: Nishad Kamdar <nishadkamdar@xxxxxxxxx>
> > ---
> > Changes in v5:
> > - Change the commit message.
> > - Restore the names of the gpio device-tree properties without
> > the "-gpio" suffix.
> > Changes in v4:
> > - Use gpiod_set_raw_value() for deassert_reset() and
> > assert_reset() as gpiod_set_value() will change the
> > sematics of these calls by taking any gpio flags
> > into account.
> > - Remove some unnecesssary line breaks.
> > - Restore 'spi_en' gpio check in fw_flashing_seq()
> > as it is currently optional.
> > Changes in v3:
> > - Add this patch in a patchset.
> > Changes in v2:
> > - Resolved compilation errors.
> > ---
>
> Also looks good now. You can add my
>
> Reviewed-by: Johan Hovold <johan@xxxxxxxxxx>
>
> Found one really minor nit below, which doesn't really need to be fixed,
> but since you may need to update the third patch, you might as well
> consider this too.
>
Ok, I'll do that.
> > /* It's not mandatory to support power management interface */
> > - apb->pwroff_gpio = of_get_named_gpio(np, "pwr-off-gpios", 0);
> > - if (apb->pwroff_gpio < 0) {
> > - dev_err(dev, "failed to get power off gpio\n");
> > - return apb->pwroff_gpio;
> > - }
> > - ret = devm_gpio_request_one(dev, apb->pwroff_gpio,
> > - GPIOF_IN, "pwroff_n");
> > - if (ret) {
> > - dev_err(dev, "Failed requesting pwroff_n gpio %d\n",
> > - apb->pwroff_gpio);
> > + apb->pwroff = devm_gpiod_get_optional(dev, "pwr-off",
> > + GPIOD_IN);
>
> Looks like you don't need to break the above statement any more either.
>
> > + if (IS_ERR(apb->pwroff)) {
> > + ret = PTR_ERR(apb->pwroff);
> > + dev_err(dev, "Failed requesting pwroff_n GPIO: %d\n", ret);
> > return ret;
> > }
> >
> > /* Do not make clock mandatory as of now (for DB3) */
> > - apb->clk_en_gpio = of_get_named_gpio(np, "clock-en-gpio", 0);
> > - if (apb->clk_en_gpio < 0) {
> > - dev_warn(dev, "failed to get clock en gpio\n");
> > - } else if (gpio_is_valid(apb->clk_en_gpio)) {
> > - ret = devm_gpio_request_one(dev, apb->clk_en_gpio,
> > - GPIOF_OUT_INIT_LOW, "apb_clk_en");
> > - if (ret) {
> > - dev_warn(dev, "Failed requesting APB clock en gpio %d\n",
> > - apb->clk_en_gpio);
> > - return ret;
> > - }
> > + apb->clk_en = devm_gpiod_get_optional(dev, "clock-en",
> > + GPIOD_OUT_LOW);
>
> Same here?
>
Ok, I'll do that.
Thanks and regards,
Nishad
> > + if (IS_ERR(apb->clk_en)) {
> > + ret = PTR_ERR(apb->clk_en);
> > + dev_err(dev, "Failed requesting APB clock en GPIO: %d\n", ret);
> > + return ret;
> > }
>
> Johan
_______________________________________________
greybus-dev mailing list
greybus-dev@xxxxxxxxxxxxxxxx
https://lists.linaro.org/mailman/listinfo/greybus-dev
|