It should be possible assuming your external endpoints can dial using IP dialing and can send a proper alias to connect to a video unit. For the polycom problem, you should consult its manual. ----- Original Message ----- From: "Chris Bradshaw" <cwbshaw@xxxxxxxxx> Subject: [HELP]: Dialing registered endpoints fromunregistered ones...how? > Hi.... > > I actually posted an email about this 2 years ago, but never got a > response.....and then I just let the problem lie because it wasn't > that urgent....until now. > > Since my original post, I have been using gnugk in proxy mode...and it > works great. > > My setup consists of PolyCom VSEX's in private address space, using gnugk > as > a proxy to connect to endpoints (registered and unregistered) on the > internet etc. > > Unfortunately, we are now getting a large number of requests by > offsite users to do video conferencing with us. Most of these want to > be able to dial to us, but having to register each user's endpoint > would be a lot of work....especially as some of them might have > changing IP addresses. > > So, I would like to be able to allow unregistered endpoints on the > internet (or anywhere really) to connect to my registered VSEX's using > gnugk to proxy the traffic..... > > Proxying all works great when I call from a registered to an > unregistered endpoint, but I don't seem to be able (also read: don't > know how) to get it to work the other way around. > > I have seen a lot of posts about this issue on the mailing list > (most/all dated after my own original posting), but none of the > solutions offered seem to help me. I have enabled > AcceptUnregisteredCalls and have set CallSignalPort=1720 (these seem > to be 2 of the most common settings mentioned in any post on this that > I have seen)....however, I still can't get it to work. > > Part of the problem may be that I don't know how to tell a Polycom > VSEX (or any video conf unit) to dial extension/endpoint XXXX via the > GnuGK IP Address A.B.C.D..... > > I have listed my current config below. There is no authorization or > authentication in this configuration....I just wanted to get it > working before I do that. > > Is what I am trying to do possible? > > If so, can anyone tell me what I might be doing wrong.....in > particular, how do I tell my PolyCom to dial an extension *via* the > Gnugk proxy? > > I would be really grateful if someone/anyone could reply to > this.....even if it is just to tell me that what I am trying to do is > not possible, so I will be able to tell my users and I can end my > search. > > Thanx muchly in advance. > > Chris Bradshaw. > > > > GnuGK config below: > > [Gatekeeper::Main] > Fourtytwo=42 > TimeToLive=600 > > [RoutedMode] > GKRouted=1 > H245Routed=1 > CallSignalPort=1720 > AcceptNeighborsCalls=1 > AcceptUnregisteredCalls=1 > CallSignalHandlerNumber=2 > RemoveH245AddressOnTunneling=1 > DropCallsByReleaseComplete=1 > SupportNATedEndpoints=1 > Q931PortRange=30000-39999 > H245PortRange=40000-49999 > > [Proxy] > Enable=1 > InternalNetwork=X.X.X.X/Y > T120PortRange=50000-59999 > RTPPortRange=50000-59999 > > [GkStatus::Auth] > rule= explicit | regex > 127.0.0.1=allow > default=forbid > > [RasSrv::Neighbors] > IRL-GK=GnuGK > > [Neighbor::IRL-GK] > GatekeeperIdentifier=IRL-GK > Host=X.X.X.X > SendPrefixes=00 > AcceptPrefixes=* > ForwardLRQ=always > ForwardResponse=1 > AcceptForwardedLRQ=1 > > [Endpoint::RewriteE164] > .=AAAAAAAAAA. > > [RasSrv::RewriteE164] > AAAAAAAAAA.=. > > [RasSrv::LRQFeatures] > NeighborTimeout=10 > IncludeDestinationInfoInLCF=0 > ForwardHopCount=10 > AcceptForwardedLRQ=1 > CiscoGKCompatible=1 ------------------------------------------------------------------------- Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV _______________________________________________________ Posting: mailto:Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549 Unsubscribe: http://lists.sourceforge.net/lists/listinfo/openh323gk-users Homepage: http://www.gnugk.org/
