Hello,
I have met following problem during my experiments with Cisco CallManager, H.323 GW and openh323gk:
After configuration of H.225trunk in CCM it successfully registers on the gatekeeper, but
2 minutes later, maybe after 600 seconds of TTL, when CCM tries to re-register on the gatekeeper again, the process of registration run continuosly. In the log I see following messages:
2005/08/19 17:52:27.849 2 RasSrv.cxx(173) RAS Read from 192.168.2.100:2240
2005/08/19 17:52:27.895 3 RasSrv.cxx(219) RAS
registrationRequest {
requestSeqNum = 35880
protocolIdentifier = 0.0.8.2250.0.2
discoveryComplete = FALSE
callSignalAddress = 1 entries {
[0]=ipAddress {
ip = 4 octets {
c0 a8 02 64 ...d
}
port = 2518
}
}
rasAddress = 1 entries {
[0]=ipAddress {
ip = 4 octets {
c0 a8 02 64 ...d
}
port = 2240
}
}
terminalType = {
gateway = {
protocol = 2 entries {
[0]=h323 {
supportedPrefixes = 0 entries {
}
}
[1]=voice {
supportedPrefixes = 1 entries {
[0]={
prefix = dialedDigits "1"
}
}
}
}
}
mc = FALSE
undefinedNode = FALSE
}
gatekeeperIdentifier = 3 characters {
004f 0047 004b OGK
}
endpointVendor = {
vendor = {
t35CountryCode = 181
t35Extension = 0
manufacturerCode = 18
}
}
timeToLive = 60
keepAlive = TRUE
endpointIdentifier = 9 characters {
0032 0030 0030 0034 005f 0065 006e 0064 2004_end
0070 p
}
willSupplyUUIEs = FALSE
}
2005/08/19 17:52:28.005 1 RasSrv.cxx(343) RAS RRQ Received
2005/08/19 17:52:28.020 3 RasSrv.cxx(231) RAS Send to 192.168.2.100:2240
registrationConfirm {
requestSeqNum = 35880
protocolIdentifier = 0.0.8.2250.0.2
callSignalAddress = 1 entries {
[0]=ipAddress {
ip = 4 octets {
c0 a8 01 08 ....
}
port = 0
}
}
terminalAlias = 1 entries {
[0]=h323_ID 9 characters {
0053 0041 004e 0056 0045 0041 004e 005f SANVEAN_
0031 1
}
}
gatekeeperIdentifier = 3 characters {
004f 0047 004b OGK
}
endpointIdentifier = 9 characters {
0032 0030 0030 0034 005f 0065 006e 0064 2004_end
0070 p
}
willRespondToIRR = FALSE
maintainConnection = FALSE
}
.... And so on, till to infinity, without delays. Though, I can make calls between CallManager and H.323 GW without problems in any direction. I cannot understand this behaviour. It is by design, or this is a bug somewhere in software?
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
_______________________________________________________
Posting: mailto:Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx
Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549
Unsubscribe: http://lists.sourceforge.net/lists/listinfo/openh323gk-users
Homepage: http://www.gnugk.org/
