The ARJ you showed is usually sent when the answering endpoint received direct signalling, while its gatekeeper is in routed mode. ----- Original Message ----- From: "Geoff Constable" <ccc@xxxxxxxxxx> Sent: Tuesday, March 09, 2004 2:01 PM > Hi, > I am trying to get a gnu-gk working for the first time. I would like it to > interwork with my service provider's Cisco H323 infrastructure. > > Currently I have it half working. It routes E.164 calls in to the zone and > out of the zone to other destinations where the endpoints are PolyCom iPower > 2.0.4. These remote terminals register with a Cisco MCM/proxy and are part > of the educational networks Global Dialing Scheme using a E.164 number plan. > Addresses are resolved via a top-level 'directory gatekeeper' (another > Cisco). > > But when I try to or from an MCU (a PolyCom MGC 100) in the same way (the > MCU is also registered with a Cisco), the call fails. My gnu-gk outputs > sensible LCF messages (I think the address resolution works), but then it > outputs the following: > > ARJ|192.88.9.6:1720|4401970639469:dialedDigits=100:dialedDigits=aber-penglai > s-wv > @aber.ac.uk:h323_ID|ED-JCMB-2009:h323_ID=0044011491001:dialedDigits|true|rou > teCallToGatekeeper; > > I have also tried connecting to a newer PolyCom using E.164: that works, but > it can't connect to me (Destination Unreachable) it is running current > PolyCom iPower software. I get a similar ARJ message when it tries. None of > this works using IP addresses either....and it doesn't make a difference if > the gnu-gk is in routed mode or not. > > I have asked for a copy of the config of the remote end gatekeeper Ciscos to > compare to the ones that do work, but the only other difference between the > successful calls and the unsuccessful calls is that the successful calls are > running later versions of the PolyCom software (MCU or terminal). > > Have others been able to get gnu-gk interworking with PolyComs registered > with Ciscos? > > I have tried using ArjReasonRouteCallToGatekeeper=0 - but that didn't seem > to make a difference. > > The gnu-gk config.ini file I am using is below. The gnu-gk website claims > compatibility with the Accord 100 MCU and the PolyCom 512, ViewStation and > Via Video, but it does not mention the iPower or the PolyCom MGC 100 - is > this because they don't interwork? has anyone got them to do so? > > have tried to RTFM to no avail. Any comments appreciated. > > Many thanks, > > Geoff > > (gatekeeper.ini is below signature) > > Geoff Constable > Canolfan Cyfnogaeth Rhwydwaith Fideo Cymru > Welsh Video Network Support Centre > Prifysgol Cymru, University of Wales, Aberystwyth > e: ccc@xxxxxxxxxx > ff/t: 01970 622475 > s/m: 07866 593773 > e.164: 004401101100 > vc ip: 192.88.9.6 > vc isdn: 01970 639469 > http://www.wvn.ac.uk > > [Gatekeeper::Main] > Fourtytwo=42 > Name=test-gk > > [Gatekeeper::Auth] > #method of authentication of endpoints > AliasAuth=required;RRQ > default=allow > > [RasSrv::RRQAuth] > #definition of allowable endpoints > 100=sigip:xxx.xx.x.x:1720 > 102=sigip:xxx.xx.x.x:1720 > default=reject > > [GkStatus::Auth] > #who can view the gk status > rule=explicit > xxx.xx.x.x=1 > > [RasSrv::Neighbors] > #neighbour gatekeeper - send LRQs to here > name.domain.net=xxx.xx.xx.xx:1719;* > > [RasSrv::LRQFeatures] > #parameters for forwarding LRQs to neighbour > AlwaysForwardLRQ=1 > IncludeDestinationInfoInLCF=0 > NeighborTimeout=2 > ForwardHopCount=9 > CiscoGKCompatible=1 > ForwardHopCount=9 > > [RoutedMode] > #routed mode configuration > GKRouted=1 > H245Routed=1 > AcceptNeighborCalls=1 > RemoveH245AddressOnTunneling=1 > DropCallsByReleaseComplete=1 > SendReleaseCompleteOnDRQ=1 > > [Proxy] > #is there but we don't want it at the moment. > Enable=0 > > [RasSrv::RewriteE164] > #strip this number from incoming E164 addresses > 004401173= ------------------------------------------------------- This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click _______________________________________________ List: Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549 Homepage: http://www.gnugk.org/
