Hi Hari, Hi Sanoj,
thank you very much for your patience and your support! The problem has been solved following your instructions :-)
N.B.: in order to reduce the running time, I executed the “du” command as follows:
for i in {1..12} do du /gluster/mnt$i/brick/CSP/ans004/ftp done
and not on each brick at "/gluster/mnt$i/brick" tree level.
I hope it was a correct idea :-)
Thank you again for helping me to solve this issue. Have a good day. Mauro
Hi, There was a accounting issue in your setup. The directory ans004/ftp/CMCC-CM2-VHR4-CTR/atm/hist and ans004/ftp/CMCC-CM2-VHR4 had wrong size value on them. To fix it, you will have to set dirty xattr (an internal gluster xattr) on these directories which will mark it for calculating the values again for the directory. And then do a du on the mount after setting the xattrs. This will do a stat that will calculate and update the right values. To set dirty xattr: setfattr -n trusted.glusterfs.quota.dirty -v 0x3100 <path to the directory> This has to be done for both the directories one after the other on each brick. Once done for all the bricks issue the du command. Thanks to Sanoj for the guidance On Tue, Jul 10, 2018 at 6:37 PM Mauro Tridici < mauro.tridici@xxxxxxx> wrote:
Hi Hari,
sorry for the late.
Yes, the gluster volume is a single volume that is spread between all the 3 node and has 36 bricks
In attachment you can find a tar.gz file containing:
- gluster volume status command output;
- gluster volume info command output;
- the output of the following script execution (it generated 3 files per server: s01.log, s02.log, s03.log).
This is the “check.sh” script that has been executed on each server (servers are s01, s02, s03).
#!/bin/bash
#set -xv
host=$(hostname)
for i in {1..12}
do
./quota_fsck_new-6.py --full-logs --sub-dir CSP/ans004 /gluster/mnt$i/brick >> $host.log
done
Many thanks,
Mauro
Il giorno 10 lug 2018, alle ore 12:12, Hari Gowtham <hgowtham@xxxxxxxxxx> ha scritto:
Hi Mauro,
Can you send the gluster v status command output?
Is it a single volume that is spread between all the 3 node and has 36 bricks?
If yes, you will have to run on all the bricks.
In the command use sub-dir option if you are running only for the
directory where limit is set. else if you are
running on the brick mount path you can remove it.
The full-log will consume a lot of space as its going to record the
xattrs for each entry inside the path we are
running it. This data is needed to cross check and verify quota's
marker functionality.
To reduce resource consumption you can run it on one replica set alone
(if its replicate volume)
But its better if you can run it on all the brick if possible and if
the size consumed is fine with you.
Make sure you run it with the script link provided above by Sanoj. (patch set 6)
On Tue, Jul 10, 2018 at 2:54 PM Mauro Tridici <mauro.tridici@xxxxxxx> wrote:
Hi Hari,
thank you very much for your answer.
I will try to use the script mentioned above pointing to each backend bricks.
So, if I understand, since I have a gluster cluster composed by 3 nodes (with 12 bricks on each node), I have to execute the script 36 times. Right?
You can find below the “df” command output executed on a cluster node:
/dev/mapper/cl_s01-gluster 100G 33M 100G 1% /gluster
/dev/mapper/gluster_vgd-gluster_lvd 9,0T 5,6T 3,5T 62% /gluster/mnt2
/dev/mapper/gluster_vge-gluster_lve 9,0T 5,7T 3,4T 63% /gluster/mnt3
/dev/mapper/gluster_vgj-gluster_lvj 9,0T 5,7T 3,4T 63% /gluster/mnt8
/dev/mapper/gluster_vgc-gluster_lvc 9,0T 5,6T 3,5T 62% /gluster/mnt1
/dev/mapper/gluster_vgl-gluster_lvl 9,0T 5,8T 3,3T 65% /gluster/mnt10
/dev/mapper/gluster_vgh-gluster_lvh 9,0T 5,7T 3,4T 64% /gluster/mnt6
/dev/mapper/gluster_vgf-gluster_lvf 9,0T 5,7T 3,4T 63% /gluster/mnt4
/dev/mapper/gluster_vgm-gluster_lvm 9,0T 5,4T 3,7T 60% /gluster/mnt11
/dev/mapper/gluster_vgn-gluster_lvn 9,0T 5,4T 3,7T 60% /gluster/mnt12
/dev/mapper/gluster_vgg-gluster_lvg 9,0T 5,7T 3,4T 64% /gluster/mnt5
/dev/mapper/gluster_vgi-gluster_lvi 9,0T 5,7T 3,4T 63% /gluster/mnt7
/dev/mapper/gluster_vgk-gluster_lvk 9,0T 5,8T 3,3T 65% /gluster/mnt9
I will execute the following command and I will put here the output.
./quota_fsck_new.py --full-logs --sub-dir /gluster/mnt{1..12}
Thank you again for your support.
Regards,
Mauro
Il giorno 10 lug 2018, alle ore 11:02, Hari Gowtham <hgowtham@xxxxxxxxxx> ha scritto:
Hi,
There is no explicit command to backup all the quota limits as per my
understanding. need to look further about this.
But you can do the following to backup and set it.
Gluster volume quota volname list which will print all the quota
limits on that particular volume.
You will have to make a note of the directories with their respective limit set.
Once noted down, you can disable quota on the volume and then enable it.
Once enabled, you will have to set each limit explicitly on the volume.
Before doing this we suggest you can to try running the script
mentioned above with the backend brick path instead of the mount path.
you need to run this on the machines where the backend bricks are
located and not on the mount.
On Mon, Jul 9, 2018 at 9:01 PM Mauro Tridici <mauro.tridici@xxxxxxx> wrote:
Hi Sanoj,
could you provide me the command that I need in order to backup all quota limits?
If there is no solution for this kind of problem, I would like to try to follow your “backup” suggestion.
Do you think that I should contact gluster developers too?
Thank you very much.
Regards,
Mauro
Il giorno 05 lug 2018, alle ore 09:56, Mauro Tridici <mauro.tridici@xxxxxxx> ha scritto:
Hi Sanoj,
unfortunately the output of the command execution was not helpful.
[root@s01 ~]# find /tier2/CSP/ans004 | xargs getfattr -d -m. -e hex
[root@s01 ~]#
Do you have some other idea in order to detect the cause of the issue?
Thank you again,
Mauro
Il giorno 05 lug 2018, alle ore 09:08, Sanoj Unnikrishnan <sunnikri@xxxxxxxxxx> ha scritto:
Hi Mauro,
A script issue did not capture all necessary xattr.
Could you provide the xattrs with..
find /tier2/CSP/ans004 | xargs getfattr -d -m. -e hex
Meanwhile, If you are being impacted, you could do the following
back up quota limits
disable quota
enable quota
freshly set the limits.
Please capture the xattr values first, so that we can get to know what went wrong.
Regards,
Sanoj
On Tue, Jul 3, 2018 at 4:09 PM, Mauro Tridici <mauro.tridici@xxxxxxx> wrote:
Dear Sanoj,
thank you very much for your support.
I just downloaded and executed the script you suggested.
This is the full command I executed:
./quota_fsck_new.py --full-logs --sub-dir /tier2/CSP/ans004/ /gluster
In attachment, you can find the logs generated by the script.
What can I do now?
Thank you very much for your patience.
Mauro
Il giorno 03 lug 2018, alle ore 11:34, Sanoj Unnikrishnan <sunnikri@xxxxxxxxxx> ha scritto:
Hi Mauro,
This may be an issue with update of backend xattrs.
To RCA further and provide resolution could you provide me with the logs by running the following fsck script.
https://review.gluster.org/#/c/19179/6/extras/quota/quota_fsck.py
Try running the script and revert with the logs generated.
Thanks,
Sanoj
On Mon, Jul 2, 2018 at 2:21 PM, Mauro Tridici <mauro.tridici@xxxxxxx> wrote:
Dear Users,
I just noticed that, after some data deletions executed inside "/tier2/CSP/ans004” folder, the amount of used disk reported by quota command doesn’t reflect the value indicated by du command.
Surfing on the web, it seems that it is a bug of previous versions of Gluster FS and it was already fixed.
In my case, the problem seems unfortunately still here.
How can I solve this issue? Is it possible to do it without starting a downtime period?
Thank you very much in advance,
Mauro
[root@s01 ~]# glusterfs -V
glusterfs 3.10.5
Repository revision: git://git.gluster.org/glusterfs.git
Copyright (c) 2006-2016 Red Hat, Inc. <https://www.gluster.org/>
GlusterFS comes with ABSOLUTELY NO WARRANTY.
It is licensed to you under your choice of the GNU Lesser
General Public License, version 3 or any later version (LGPLv3
or later), or the GNU General Public License, version 2 (GPLv2),
in all cases as published by the Free Software Foundation.
[root@s01 ~]# gluster volume quota tier2 list /CSP/ans004
Path Hard-limit Soft-limit Used Available Soft-limit exceeded? Hard-limit exceeded?
-------------------------------------------------------------------------------------------------------------------------------
/CSP/ans004 1.0TB 99%(1013.8GB) 3.9TB 0Bytes Yes Yes
[root@s01 ~]# du -hs /tier2/CSP/ans004/
295G /tier2/CSP/ans004/
_______________________________________________
Gluster-users mailing list
Gluster-users@xxxxxxxxxxx
http://lists.gluster.org/mailman/listinfo/gluster-users
_______________________________________________
Gluster-users mailing list
Gluster-users@xxxxxxxxxxx
https://lists.gluster.org/mailman/listinfo/gluster-users
--
Regards,
Hari Gowtham.
--
Regards,
Hari Gowtham.
-- Regards, Hari Gowtham.
|
