>Hello, >Has anyone successfully configured bcm43xx modules? >Any help would be appreciated. I was able to get my Linksys WPC54G card working with the bcm43xx module. I followed the instructions below which were posted to one of the fedora lists. I have the .2080 kernel installed and my card works great with WEP. I use the default rate of 11M...54M didn't work. -Brian If you haven't already done so, update to the 2.6.16-1.2071_FC5 or later kernel, from http://people.redhat.com/davej/kernels/Fedora/FC5/ if it isn't in the official repos yet. The bcm43xx driver _does_ work in the 2054 release kernel, and I've been using it like that for months, but it's far less picky about its initialisation in 2071, and doesn't lose the network every time NetworkManager scans -- so for the sake of the HOWTO it's just easier if you upgrade. The improvements to the driver _will_ be in the official kernel update when it eventually comes out. Install the bcm43xx-fwcutter package from Extras. It's in extras-devel, but not yet in extras-fc5 yet because my request to create the branch hasn't been honoured yet. There's a copy of it at http://david.woodhou.se/bcm43xx-fwcutter-003-2.ppc.rpm (there's also i386 and src rpms there). (By next week, hopefully the above will be reduced to 'yum update kernel ; yum install bcm43xx-fwcutter') Then proceed as described in /usr/share/doc/bcm43xx-fwcutter-003/README.Fedora: As root, extract the firmware from your Windows or MacOS driver by running the command bcm43xx-fwcutter -w /lib/firmware <DRIVERFILE> The README file in the same directory (not README.Fedora but just README) contains a bunch of links to drivers if you don't have one. Apparently, any of them should be OK; it doesn't matter which you use. Load the driver by 'modprobe bcm43xx'. NetworkManager should work with it, as should system-config-network and the standard initscripts. WEP works, and according to my limited testing WPA works too, as long as your AP is broadcasting its ESSID (that latter restriction seems to apply to _many_ cards, in fact. There's a hack to work around it at http://david.woodhou.se/wpa_supplicant-hack.patch) We disabled the automatic loading of the bcm43xx driver in FC5 because it's quite new and experimental, and partly because of the bugs which have now been fixed in the 2071 kernel. To make sure the driver gets loaded automatically, either add '/sbin/modprobe bcm43xx' to your /etc/rc.local script, or copy the alias list from /usr/share/doc/bcm43xx-fwcutter-003/modprobe.bcm43xx into the /etc/modprobe.d directory, which tells the module loaded which PCI IDs to associate with the bcm43xx driver. Finally, give us feedback in bugzilla so we can know if/when we should enable the driver by default again: https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=186329 Please leave feedback even if it's working -- if the only people we hear from are those who can't get it to work, then we're _never_ going to enable it by default. :) If you can't get it to work, try bringing it up by hand using 'ifconfig' and 'iwconfig' commands, and show/attach the kernel output ('dmesg') from when you do so. Also try adjusting the rate (iwconfig eth1 rate 2M) and setting the SSID again. We already default to 11M, but that might not be slow enough in some situations -- we don't automatically fall back when the link is poor, so you have to set the speed manually. -- fedora-test-list mailing list fedora-test-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-test-list