Hiya,
this has been discussed in the past, but 2.6.10-ac2 mentioned
something about CSB6, so I tried fc3, updated to 2.6.10.
the hardware is HP Proliant ML330. a couple of ide-drives in a raid1.
I'd like to get them detected :-)
Linux version 2.6.10-1.760_FC3smp (bhcompile@xxxxxxxxxxxxxxxxxxxxx) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #1 SMP Wed Feb 2 00:29:03 EST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fffa000 (usable)
BIOS-e820: 000000000fffa000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
found SMP MP-table at 000f4fd0
On node 0 totalpages: 65530
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61434 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 COMPAQ ) @ 0x000f4f70
ACPI: RSDT (v001 COMPAQ D15 0x00000002 р 0x0000162e) @ 0x0fffa000
ACPI: FADT (v001 COMPAQ D15 0x00000002 р 0x0000162e) @ 0x0fffa040
ACPI: MADT (v001 COMPAQ 00000083 0x00000002 р 0x0000162e) @ 0x0fffa100
ACPI: SPCR (v001 COMPAQ SPCRRBSU 0x00000001 р 0x0000162e) @ 0x0fffa1c0
ACPI: DSDT (v001 COMPAQ DSDT 0x00000001 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0x920
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] disabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-15
ACPI: IOAPIC (id[0x03] address[0xfec01000] gsi_base[16])
IOAPIC[1]: apic_id 3, version 17, address 0xfec01000, GSI 16-31
ACPI: IOAPIC (id[0x04] address[0xfec02000] gsi_base[32])
IOAPIC[2]: apic_id 4, version 17, address 0xfec02000, GSI 32-47
ACPI: IOAPIC (id[0x05] address[0xfec03000] gsi_base[48])
IOAPIC[3]: apic_id 5, version 17, address 0xfec03000, GSI 48-63
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 4 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: ro root=LABEL=/1
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
mapped IOAPIC to ffffb000 (fec01000)
mapped IOAPIC to ffffa000 (fec02000)
mapped IOAPIC to ffff9000 (fec03000)
Initializing CPU#0
CPU 0 irqstacks, hard=c03ca000 soft=c03aa000
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 2400.227 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 254148k/262120k available (1780k kernel code, 7372k reserved, 718k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4751.36 BogoMIPS (lpj=2375680)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebf3ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Xeon(TM) CPU 2.40GHz stepping 09
per-CPU timeslice cutoff: 1462.38 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c03cb000 soft=c03ab000
Initializing CPU#1
Calibrating delay loop... 4784.12 BogoMIPS (lpj=2392064)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebf3ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Xeon(TM) CPU 2.40GHz stepping 09
Total of 2 processors activated (9535.48 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
checking if image is initramfs... it is
Freeing initrd memory: 515k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0094, last bus=0
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:0e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [IUSB] (IRQs 4 5 7 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [RAID] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [IN18] (IRQs 4 *5 7 10 11 15)
ACPI: PCI Interrupt Link [IN19] (IRQs 4 5 7 10 11 15) *3
ACPI: PCI Interrupt Link [IN21] (IRQs 4 5 7 *10 11 15)
ACPI: PCI Interrupt Link [IN22] (IRQs 4 5 7 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [IN23] (IRQs 4 5 7 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [IN24] (IRQs 4 5 7 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [IN25] (IRQs 4 5 7 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [IN26] (IRQs 4 5 7 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [IN27] (IRQs 4 5 7 10 *11 15)
ACPI: PCI Interrupt Link [IN28] (IRQs 4 5 7 10 11 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@xxxxxx
** so I can fix the driver.
PCI: Device 00:00 not found by BIOS
PCI: Device 00:01 not found by BIOS
PCI: Device 00:78 not found by BIOS
PCI: Device 00:7b not found by BIOS
pnp: 00:00: ioport range 0xf50-0xf58 has been reserved
pnp: 00:00: ioport range 0x408-0x40f has been reserved
pnp: 00:00: ioport range 0x900-0x903 could not be reserved
pnp: 00:00: ioport range 0x904-0x904 has been reserved
pnp: 00:00: ioport range 0x910-0x911 could not be reserved
pnp: 00:00: ioport range 0x920-0x923 could not be reserved
pnp: 00:00: ioport range 0x930-0x937 has been reserved
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1107560271.030:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 825948347B50E07F
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Thermal Zone [THM0] (8 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks CSB6: IDE controller at PCI slot 0000:00:0e.0
SvrWks CSB6: chipset revision 160
SvrWks CSB6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2000-0x2007, BIOS settings: hda:pio, hdb:DMA
Probing IDE interface ide0...
hda: Maxtor 2F040J0, ATA DISK drive
hdb: TDK DVDRW0404N, ATAPI CD/DVD-ROM drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide1: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63
hda: cache flushes supported
hda: hda1 hda2 hda4 < hda5 >
hdb: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: PS/2 Logitech Mouse on isa0060/serio1
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 16Kbytes
TCP: Hash tables configured (established 8192 bind 10922)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
ACPI: (supports S0 S4 S5)
CPU0:
domain 0: span 00000003
groups: 00000001 00000002
domain 1: span 00000003
groups: 00000003
CPU1:
domain 0: span 00000003
groups: 00000002 00000001
domain 1: span 00000003
groups: 00000003
Freeing unused kernel memory: 204k freed
SCSI subsystem initialized
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 21 (level, low) -> IRQ 169
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec (Compaq OEM) 29160 Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=1, 32/253 SCBs
(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
Vendor: COMPAQ Model: BD03695A27 Rev: HPB6
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:0:0: Tagged Queuing enabled. Depth 4
SCSI device sda: 71132000 512-byte hdwr sectors (36420 MB)
SCSI device sda: drive cache: write through
SCSI device sda: 71132000 512-byte hdwr sectors (36420 MB)
SCSI device sda: drive cache: write through
sda: sda1 sda2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security: 3 users, 4 roles, 315 types, 20 bools
security: 53 classes, 10657 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs), not configured for labeling
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 27 (level, low) -> IRQ 177
eth0: ns83820.c: 0x22c: 0022100b, subsystem: 100b:0022
eth0: detected 64 bit PCI data bus.
eth0: using 64 bit addressing.
eth0: ns83820 v0.20+: DP83820 v1.2: 00:03:ce:10:0c:10 io=0xf6fb0000 irq=177 f=h,sg
divert: allocating divert_blk for eth0
tg3.c:v3.14 (November 15, 2004)
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 185
divert: allocating divert_blk for eth1
eth1: Tigon3 [partno(N/A) rev 1002 PHY(5703)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:0e:7f:fd:fe:e9
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
piix4_smbus 0000:00:0f.0: Found 0000:00:0f.0 device
piix4_smbus 0000:00:0f.0: Unusual config register value
piix4_smbus 0000:00:0f.0: Try using fix_hstcfg=1 if you experience problems
piix4_smbus 0000:00:0f.0: Illegal Interrupt configuration (or code out of date)!
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
EXT3 FS on sda1, internal journal
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@xxxxxxxxxx
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2048248k swap on /dev/hda2. Priority:-1 extents:1
Adding 2048276k swap on /dev/sda2. Priority:-2 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Trying to free free DMA0
pnp: Device 00:06 disabled.
ieee1394: Initialized config rom entry `ip1394'
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
tg3: eth1: Link is up at 1000 Mbps, full duplex.
tg3: eth1: Flow control is on for TX and on for RX.
pnp: Device 00:06 activated.
parport: PnPBIOS parport detected.
pnp: Device 00:06 disabled.
lp: driver loaded but no devices found
NET: Registered protocol family 10
Disabled Privacy Extensions on device c032a200(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
eth1: no IPv6 routers present
tg3: eth1: Link is down.
tg3: eth1: Link is up at 1000 Mbps, full duplex.
tg3: eth1: Flow control is on for TX and on for RX.
tg3: eth1: Link is down.
tg3: eth1: Link is up at 1000 Mbps, full duplex.
tg3: eth1: Flow control is on for TX and on for RX.
lspci -vvv:
00:00.0 Host bridge: ServerWorks GCNB-LE Host Bridge (rev 32)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.1 Host bridge: ServerWorks GCNB-LE Host Bridge
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:03.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation: Unknown device 001e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size 10
Region 0: Memory at f7000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 2400 [size=256]
Region 2: Memory at f6ff0000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5702X Gigabit Ethernet (rev 02)
Subsystem: Compaq Computer Corporation NC7760 Gigabit Server Adapter (PCI-X, 10/100/1000-T)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 185
Region 0: Memory at f6fe0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=255 Dev=31 Func=1 64bit+ 133MHz+ SCD- USC-, DC=simple, DMMRBC=2, DMOST=0, DMCRS=1, RSCEM-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 279020000cc21000 Data: 8099
00:05.0 System peripheral: Compaq Computer Corporation Advanced System Management Controller
Subsystem: Compaq Computer Corporation: Unknown device b0f3
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 1800 [size=256]
Region 1: Memory at f6fd0000 (32-bit, non-prefetchable) [size=256]
00:06.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
Subsystem: Compaq Computer Corporation Compaq 64-Bit/66MHz Wide Ultra3 SCSI Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (10000ns min, 6250ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 169
BIST result: 00
Region 0: I/O ports at 2800 [disabled] [size=256]
Region 1: Memory at f6fc0000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Ethernet controller: National Semiconductor Corporation DP83820 10/100/1000 Ethernet Controller
Subsystem: National Semiconductor Corporation DP83820 10/100/1000 Ethernet Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2750ns min, 13000ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at 2c00 [size=256]
Region 1: Memory at f6fb0000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 IDE interface: ServerWorks: Unknown device 0217 (rev a0) (prog-if 82 [Master PriP])
Subsystem: ServerWorks: Unknown device 0213
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin ? routed to IRQ 14
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 2000 [size=16]
Capabilities: [b0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.0 ISA bridge: ServerWorks CSB6 South Bridge (rev a0)
Subsystem: ServerWorks: Unknown device 0201
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
00:0f.3 Host bridge: ServerWorks GCLE-2 Host Bridge
Subsystem: ServerWorks: Unknown device 0230
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
lspci -n:
00:00.0 Class 0600: 1166:0017 (rev 32)
00:00.1 Class 0600: 1166:0017
00:03.0 Class 0300: 1002:4752 (rev 27)
00:04.0 Class 0200: 14e4:16a6 (rev 02)
00:05.0 Class 0880: 0e11:a0f0
00:06.0 Class 0100: 9005:0080 (rev 02)
00:09.0 Class 0200: 100b:0022
00:0e.0 Class 0101: 1166:0217 (rev a0)
00:0f.0 Class 0601: 1166:0203 (rev a0)
00:0f.3 Class 0600: 1166:0227
--
Igor "CacoDem0n" Grabin, http://violent.death.kiev.ua/