-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Truls Gulbrandsen wrote: | Truls Gulbrandsen wrote: | | Jim Cornette wrote: | | | Truls Gulbrandsen wrote: | | | | | |> -----BEGIN PGP SIGNED MESSAGE----- | | |> Hash: SHA1 | | |> | | |> Hi, | | |> I have now installed fc3 to my desktop an IBM PC300PL with an IBM912 | | |> T521 LCD screen the video card is VESA | | |> | | |> ...snip | | | | | | | | | I looked up the specs for your desktop. The video info is below. The | | | vesa driver is sort of a generic driver. Is the S3 Trio listed? | | | | | | Have you tried to add the desired resolution into your xorg.conf file? | | | Say "1024x768" "800x600" in front of the "640x480" entry? | | | | | | Jim | | | | | | Monitor and Graphics | | | Video Integration Integrated | | | Installed Video Memory 4 MB | | | Included Video Card Graphic card - AGP - S3 Trio3D integrated | | | | | | | | |> | | |> Regards, | | |> Truls | | | | | | | | Thanks for feedback. | | | | Yes the correct video card is Trio 64 3D and it is listed. So I went | | system settings ==> display and set the correct video card. | | | | Then I got an error message saying that the system would log out of X | | and correct an error. It never came back. So I rebooted but now the | | boot sequence goes to: | | | | Starting udev: (ok) | | Initializing hardware..... storage network audio done (ok) | | Configuring kernel parameters: | | | | and there it hangs unresponsive. | | | | Probably I have to start the install process over again? | | | | Regards, | | Truls | | I found that when hittin ctrl-C after the system hangs it actually | continues to boot and gives me a command line. | | The problem is that system settings - display did not update my | xorg.conf file correctly. The driver name for the video card was not | replaced with the corect one but ended up as mix of "Vesa" and "S3Trio3D" | | I tried to correct this using vi but am not able to open the file in | edit modus. I'm told it is a read only file. | | Any suggestions? | | Truls Ok, I have followed all advices given under this thread without success. So, I did a fresh install of FC3 from the cds and the following happens. Upon installation fc doesn't recognize my video card and set it up as VESA generic. That works in the way that my screen background seem to have the correct resolution but applications and icons etc. seems work at 640x480. Then, when I change to video card S3 Trio64 3D and reboot I'm back to the original problem. The systems load all the way to: Starting udev: (ok) Initializing hardware..... storage network audio done (ok) Configuring kernel parameters: ~ <then I have to enter Ctrl-C to make it continue> INIT: Entering runlevel: 5 Starting readahead early: (ok) Checking for new hardware: (ok) touch: cannot touch '/var/touch/subsys/kudzu': Read-only file system Applying iptables: firewal rules (ok) touch: cannot touch '/var/touch/subsys/iptables': Read-only file system Starting pcmcia: (ok) etc etc Am I doing something wrong or the system? Regards Truls -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (GNU/Linux) Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org iD8DBQFBlQhCickK29LSyG8RAvBIAKCWT1Lynj/2ns3DK8Lt6DsLnppE4QCfUcoj akjvYq67RNz5gYWjDmy6NwQ= =Mig3 -----END PGP SIGNATURE-----
begin:vcard fn:Truls Gulbrandsen n:Gulbrandsen;Truls org:Oslo Philharmonic Orchestra adr:;;;Oslo;;;Norway email;internet:trulsg@xxxxxxxxxxxx tel;cell:+47 928 24 434 x-mozilla-html:FALSE url:http://www.oslophil.com version:2.1 end:vcard