Am Donnerstag, den 02.06.2011, 12:16 -0400 schrieb Bernd Stramm: > On Thu, 2 Jun 2011 17:07:47 +0100 > "Richard W.M. Jones" <rjones@xxxxxxxxxx> wrote: > > > On Thu, Jun 02, 2011 at 06:00:44PM +0200, BjÃrn Persson wrote: > > > Daniel P. Berrange wrote: > > > > On Thu, Jun 02, 2011 at 04:40:10PM +0100, Richard W.M. Jones > > > > wrote: > > > > > The Linux machines on my LAN appear to have acquired IPv6 > > > > > addresses, eg: > > > > > > > > > > $ ip addr show eth0 > > > > > 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc > > > > > pfifo_fast state UNKNOWN qlen 1000 > > > > > > > > > > link/ether 00:e0:81:74:02:28 brd ff:ff:ff:ff:ff:ff > > > > > inet 192.168.0.128/24 brd 192.168.0.255 scope global eth0 > > > > > inet6 fe80::2e0:81ff:fe74:228/64 scope link > > > > > > > > > > valid_lft forever preferred_lft forever > > > > > > > > > > but pinging them gives me strange errors: > > > > > > > > > > $ ping6 fe80::2e0:81ff:fe74:228/64 > > > > > unknown host > > > > > $ ping6 fe80::2e0:81ff:fe74:228 > > > > > connect: Invalid argument > > > > > $ ping6 fe80::2e0:81ff:fe74 > > > > > connect: Invalid argument > > > > > > > > Anything with an fe80:: prefix is a link local address, which > > > > is only unique within the scope of a single LAN segment. Thus > > > > if you want to send traffic to such addresses, you need to specify > > > > the NIC to send the traffic out from. The vast majority of apps > > > > using sockets have no way to let you do this. > > > > > > Ping6 has a way though: > > > > > > $ ping6 -I eth0 fe80::200:24ff:fec9:2e0c > > > PING fe80::200:24ff:fec9:2e0c(fe80::200:24ff:fec9:2e0c) from > > > fe80::21e:8cff:fecf:cde5 eth0: 56 data bytes > > > 64 bytes from fe80::200:24ff:fec9:2e0c: icmp_seq=1 ttl=64 time=1.69 > > > ms 64 bytes from fe80::200:24ff:fec9:2e0c: icmp_seq=2 ttl=64 > > > time=0.263 ms > > > > But that's not so useful if no other programs can use these addresses. > > Is there a way to assign "proper" addresses? Just run radvd and > > configure it with a random prefix? > > Instead of random, you may want to use a Unique Local Address prefix, > following > http://www.ripe.net/lir-services/resource-management/ipv6/ipv6-address-types > I brought this up some time ago: Assigning ULA instead of LL would be somewhat more user friendly: https://bugzilla.gnome.org/show_bug.cgi?id=615063 https://bugzilla.redhat.com/show_bug.cgi?id=581579 In my eyes just assigning a LL adress is not very user friendly. > > > > Rich. > > > > > > -- > Bernd Stramm > bernd.stramm@xxxxxxxxx > -- devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxxx https://admin.fedoraproject.org/mailman/listinfo/devel
