On Tue, Feb 18, 2025 at 03:01:30PM -0800, mhkelley58@xxxxxxxxx wrote:
> From: Michael Kelley <mhklinux@xxxxxxxxxxx>
>
> Gen 2 Hyper-V VMs boot via EFI and have a standard EFI framebuffer
> device. When the kdump kernel runs in such a VM, loading the efifb
> driver may hang because of accessing the framebuffer at the wrong
> memory address.
>
> The scenario occurs when the hyperv_fb driver in the original kernel
> moves the framebuffer to a different MMIO address because of conflicts
> with an already-running efifb or simplefb driver. The hyperv_fb driver
> then informs Hyper-V of the change, which is allowed by the Hyper-V FB
> VMBus device protocol. However, when the kexec command loads the kdump
> kernel into crash memory via the kexec_file_load() system call, the
> system call doesn't know the framebuffer has moved, and it sets up the
> kdump screen_info using the original framebuffer address. The transition
> to the kdump kernel does not go through the Hyper-V host, so Hyper-V
> does not reset the framebuffer address like it would do on a reboot.
> When efifb tries to run, it accesses a non-existent framebuffer
> address, which traps to the Hyper-V host. After many such accesses,
> the Hyper-V host thinks the guest is being malicious, and throttles
> the guest to the point that it runs very slowly or appears to have hung.
>
> When the kdump kernel is loaded into crash memory via the kexec_load()
> system call, the problem does not occur. In this case, the kexec command
> builds the screen_info table itself in user space from data returned
> by the FBIOGET_FSCREENINFO ioctl against /dev/fb0, which gives it the
> new framebuffer location.
>
> This problem was originally reported in 2020 [1], resulting in commit
> 3cb73bc3fa2a ("hyperv_fb: Update screen_info after removing old
> framebuffer"). This commit solved the problem by setting orig_video_isVGA
> to 0, so the kdump kernel was unaware of the EFI framebuffer. The efifb
> driver did not try to load, and no hang occurred. But in 2024, commit
> c25a19afb81c ("fbdev/hyperv_fb: Do not clear global screen_info")
> effectively reverted 3cb73bc3fa2a. Commit c25a19afb81c has no reference
> to 3cb73bc3fa2a, so perhaps it was done without knowing the implications
> that were reported with 3cb73bc3fa2a. In any case, as of commit
> c25a19afb81c, the original problem came back again.
>
> Interestingly, the hyperv_drm driver does not have this problem because
> it never moves the framebuffer. The difference is that the hyperv_drm
> driver removes any conflicting framebuffers *before* allocating an MMIO
> address, while the hyperv_fb drivers removes conflicting framebuffers
> *after* allocating an MMIO address. With the "after" ordering, hyperv_fb
> may encounter a conflict and move the framebuffer to a different MMIO
> address. But the conflict is essentially bogus because it is removed
> a few lines of code later.
>
> Rather than fix the problem with the approach from 2020 in commit
> 3cb73bc3fa2a, instead slightly reorder the steps in hyperv_fb so
> conflicting framebuffers are removed before allocating an MMIO address.
> Then the default framebuffer MMIO address should always be available, and
> there's never any confusion about which framebuffer address the kdump
> kernel should use -- it's always the original address provided by
> the Hyper-V host. This approach is already used by the hyperv_drm
> driver, and is consistent with the usage guidelines at the head of
> the module with the function aperture_remove_conflicting_devices().
>
> This approach also solves a related minor problem when kexec_load()
> is used to load the kdump kernel. With current code, unbinding and
> rebinding the hyperv_fb driver could result in the framebuffer moving
> back to the default framebuffer address, because on the rebind there
> are no conflicts. If such a move is done after the kdump kernel is
> loaded with the new framebuffer address, at kdump time it could again
> have the wrong address.
>
> This problem and fix are described in terms of the kdump kernel, but
> it can also occur with any kernel started via kexec.
>
> See extensive discussion of the problem and solution at [2].
>
> [1] https://lore.kernel.org/linux-hyperv/20201014092429.1415040-1-kasong@xxxxxxxxxx/
> [2] https://lore.kernel.org/linux-hyperv/BLAPR10MB521793485093FDB448F7B2E5FDE92@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx/
>
> Reported-by: Thomas Tai <thomas.tai@xxxxxxxxxx>
> Fixes: c25a19afb81c ("fbdev/hyperv_fb: Do not clear global screen_info")
> Signed-off-by: Michael Kelley <mhklinux@xxxxxxxxxxx>
Applied to hyperv-fixes, thanks!
