Re: [PATCH v4 2/3] drm/bridge: ti-sn65dsi83: Add ti,lvds-vod-swing optional properties

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 10. 12. 24 02:18, Dmitry Baryshkov wrote:
On Mon, Dec 09, 2024 at 08:56:29AM +0100, Andrej Picej wrote:
Hi Dmitry,

On 5. 12. 24 23:48, Dmitry Baryshkov wrote:
On Thu, Dec 05, 2024 at 02:40:20PM +0100, Andrej Picej wrote:
Add a optional properties to change LVDS output voltage. This should not
be static as this depends mainly on the connected display voltage
requirement. We have three properties:
- "ti,lvds-termination-ohms", which sets near end termination,
- "ti,lvds-vod-swing-data-microvolt" and
- "ti,lvds-vod-swing-clock-microvolt" which both set LVDS differential
output voltage for data and clock lanes. They are defined as an array
with min and max values. The appropriate bitfield will be set if
selected constraints can be met.

If "ti,lvds-termination-ohms" is not defined the default of 200 Ohm near
end termination will be used. Selecting only one:
"ti,lvds-vod-swing-data-microvolt" or
"ti,lvds-vod-swing-clock-microvolt" can be done, but the output voltage
constraint for only data/clock lanes will be met. Setting both is
recommended.

Signed-off-by: Andrej Picej <andrej.picej@xxxxxxxxx>
---
Changes in v4:
- fix typo in commit message bitfiled -> bitfield
- use arrays (lvds_vod_swing_conf and lvds_term_conf) in private data, instead
of separate variables for channel A/B
- add more checks on return value of "of_property_read_u32_array"
Changes in v3:
- use microvolts for default array values 1000 mV -> 1000000 uV.
Changes in v2:
- use datasheet tables to get the proper configuration
- since major change was done change the authorship to myself
---
   drivers/gpu/drm/bridge/ti-sn65dsi83.c | 147 +++++++++++++++++++++++++-
   1 file changed, 144 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi83.c b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
index 57a7ed13f996..f724d2a6777b 100644
--- a/drivers/gpu/drm/bridge/ti-sn65dsi83.c
+++ b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
@@ -132,6 +132,16 @@
   #define  REG_IRQ_STAT_CHA_SOT_BIT_ERR		BIT(2)
   #define  REG_IRQ_STAT_CHA_PLL_UNLOCK		BIT(0)
+enum sn65dsi83_channel {
+	CHANNEL_A,
+	CHANNEL_B
+};
+
+enum sn65dsi83_lvds_term {
+	OHM_100,
+	OHM_200
+};
+
   enum sn65dsi83_model {
   	MODEL_SN65DSI83,
   	MODEL_SN65DSI84,
@@ -147,6 +157,8 @@ struct sn65dsi83 {
   	struct regulator		*vcc;
   	bool				lvds_dual_link;
   	bool				lvds_dual_link_even_odd_swap;
+	int				lvds_vod_swing_conf[2];
+	int				lvds_term_conf[2];
   };
   static const struct regmap_range sn65dsi83_readable_ranges[] = {
@@ -237,6 +249,36 @@ static const struct regmap_config sn65dsi83_regmap_config = {
   	.max_register = REG_IRQ_STAT,
   };
+static const int lvds_vod_swing_data_table[2][4][2] = {
+	{	/* 100 Ohm */
+		{ 180000, 313000 },
+		{ 215000, 372000 },
+		{ 250000, 430000 },
+		{ 290000, 488000 },
+	},
+	{	/* 200 Ohm */
+		{ 150000, 261000 },
+		{ 200000, 346000 },
+		{ 250000, 428000 },
+		{ 300000, 511000 },
+	},
+};
+
+static const int lvds_vod_swing_clock_table[2][4][2] = {
+	{	/* 100 Ohm */
+		{ 140000, 244000 },
+		{ 168000, 290000 },
+		{ 195000, 335000 },
+		{ 226000, 381000 },
+	},
+	{	/* 200 Ohm */
+		{ 117000, 204000 },
+		{ 156000, 270000 },
+		{ 195000, 334000 },
+		{ 234000, 399000 },
+	},
+};
+
   static struct sn65dsi83 *bridge_to_sn65dsi83(struct drm_bridge *bridge)
   {
   	return container_of(bridge, struct sn65dsi83, bridge);
@@ -435,12 +477,16 @@ static void sn65dsi83_atomic_pre_enable(struct drm_bridge *bridge,
   		val |= REG_LVDS_FMT_LVDS_LINK_CFG;
   	regmap_write(ctx->regmap, REG_LVDS_FMT, val);
-	regmap_write(ctx->regmap, REG_LVDS_VCOM, 0x05);
+	regmap_write(ctx->regmap, REG_LVDS_VCOM,
+			REG_LVDS_VCOM_CHA_LVDS_VOD_SWING(ctx->lvds_vod_swing_conf[CHANNEL_A]) |
+			REG_LVDS_VCOM_CHB_LVDS_VOD_SWING(ctx->lvds_vod_swing_conf[CHANNEL_B]));
   	regmap_write(ctx->regmap, REG_LVDS_LANE,
   		     (ctx->lvds_dual_link_even_odd_swap ?
   		      REG_LVDS_LANE_EVEN_ODD_SWAP : 0) |
-		     REG_LVDS_LANE_CHA_LVDS_TERM |
-		     REG_LVDS_LANE_CHB_LVDS_TERM);
+		     (ctx->lvds_term_conf[CHANNEL_A] ?
+			  REG_LVDS_LANE_CHA_LVDS_TERM : 0) |
+		     (ctx->lvds_term_conf[CHANNEL_B] ?
+			  REG_LVDS_LANE_CHB_LVDS_TERM : 0));
   	regmap_write(ctx->regmap, REG_LVDS_CM, 0x00);
   	le16val = cpu_to_le16(mode->hdisplay);
@@ -576,10 +622,101 @@ static const struct drm_bridge_funcs sn65dsi83_funcs = {
   	.atomic_get_input_bus_fmts = sn65dsi83_atomic_get_input_bus_fmts,
   };
+static int sn65dsi83_select_lvds_vod_swing(struct device *dev,
+	u32 lvds_vod_swing_data[2], u32 lvds_vod_swing_clk[2], u8 lvds_term)
+{
+	int i;
+
+	for (i = 0; i <= 3; i++) {
+		if (lvds_vod_swing_data_table[lvds_term][i][0] >= lvds_vod_swing_data[0] &&
+		lvds_vod_swing_data_table[lvds_term][i][1] <= lvds_vod_swing_data[1] &&
+		lvds_vod_swing_clock_table[lvds_term][i][0] >= lvds_vod_swing_clk[0] &&
+		lvds_vod_swing_clock_table[lvds_term][i][1] <= lvds_vod_swing_clk[1])
+			return i;
+	}
+
+	dev_err(dev, "failed to find appropriate LVDS_VOD_SWING configuration\n");
+	return -EINVAL;
+}
+
+static int sn65dsi83_parse_lvds_endpoint(struct sn65dsi83 *ctx, int channel)
+{
+	struct device *dev = ctx->dev;
+	struct device_node *endpoint;
+	/* Set so the property can be freely selected if not defined */
+	u32 lvds_vod_swing_data[2] = { 0, 1000000 };
+	u32 lvds_vod_swing_clk[2] = { 0, 1000000 };
+	u32 lvds_term = 200;
+	u8 lvds_term_conf;
+	int endpoint_reg;
+	int lvds_vod_swing_conf;
+	int ret = 0;
+	int ret_data;
+	int ret_clock;
+
+	if (channel == CHANNEL_A)
+		endpoint_reg = 2;
+	else
+		endpoint_reg = 3;
+
+	endpoint = of_graph_get_endpoint_by_regs(dev->of_node, endpoint_reg, -1);
+	of_property_read_u32(endpoint, "ti,lvds-termination-ohms", &lvds_term);
+
+	if (lvds_term == 200)
+		lvds_term_conf = OHM_200;
+	else
+		lvds_term_conf = OHM_100;
+
+	ctx->lvds_term_conf[channel] = lvds_term_conf;
+
+	ret_data = of_property_read_u32_array(endpoint,
+			"ti,lvds-vod-swing-data-microvolt", lvds_vod_swing_data,
+			ARRAY_SIZE(lvds_vod_swing_data));
+	if (ret_data != 0 && ret_data != -EINVAL) {
+		ret = ret_data;
+		goto exit;
+	}
+
+	ret_clock = of_property_read_u32_array(endpoint,
+			"ti,lvds-vod-swing-clock-microvolt", lvds_vod_swing_clk,
+			ARRAY_SIZE(lvds_vod_swing_clk));
+	if (ret_clock != 0 && ret_clock != -EINVAL) {
+		ret = ret_clock;
+		goto exit;
+	}
+
+	/* If any of the two properties is defined. */
+	if (!ret_data || !ret_clock) {
+		lvds_vod_swing_conf = sn65dsi83_select_lvds_vod_swing(dev,
+			lvds_vod_swing_data, lvds_vod_swing_clk,
+			lvds_term_conf);
+		if (lvds_vod_swing_conf < 0) {
+			ret = lvds_vod_swing_conf;
+			goto exit;
+		}
+
+		ctx->lvds_vod_swing_conf[channel] = lvds_vod_swing_conf;
+	}
+	ret = 0;
+exit:
+	of_node_put(endpoint);
+	return ret;
+}
+
   static int sn65dsi83_parse_dt(struct sn65dsi83 *ctx, enum sn65dsi83_model model)
   {
   	struct drm_bridge *panel_bridge;
   	struct device *dev = ctx->dev;
+	int ret;
+
+	ctx->lvds_vod_swing_conf[CHANNEL_A] = 0x1;
+	ctx->lvds_vod_swing_conf[CHANNEL_B] = 0x1;
+	ctx->lvds_term_conf[CHANNEL_A] = 0x1;
+	ctx->lvds_term_conf[CHANNEL_B] = 0x1;

These match the defaults in sn65dsi83_parse_lvds_endpoint(). Do we
really need those?

Yes, I think we do. This ensures that defaults are used even when property
is not defined/LVDS channel is not used. So also LVDS channel B defaults are
set even for sn65dsi83 (single LVDS output). Keeping the same reg values as
before these changes.

You can move sn65dsi83_parse_lvds_endpoint() out of the if() and get the
same result. Duplicating data (or code) is a bad idea, because it's easy
to update one point and miss another point. And then usually one has a
nice debugging session, trying to understand why their changes didn't
work out.

Ok I see what you are trying to accomplish. I'll set default values in sn65dsi83_parse_lvds_endpoint() in v5 like you suggested. Thanks.

Best regards,
Andrej



Best regards,
Andrej



+
+	ret = sn65dsi83_parse_lvds_endpoint(ctx, CHANNEL_A);
+	if (ret < 0)
+		return ret;
   	ctx->lvds_dual_link = false;
   	ctx->lvds_dual_link_even_odd_swap = false;
@@ -587,6 +724,10 @@ static int sn65dsi83_parse_dt(struct sn65dsi83 *ctx, enum sn65dsi83_model model)
   		struct device_node *port2, *port3;
   		int dual_link;
+		ret = sn65dsi83_parse_lvds_endpoint(ctx, CHANNEL_B);
+		if (ret < 0)
+			return ret;
+
   		port2 = of_graph_get_port_by_id(dev->of_node, 2);
   		port3 = of_graph_get_port_by_id(dev->of_node, 3);
   		dual_link = drm_of_lvds_get_dual_link_pixel_order(port2, port3);
--
2.34.1






[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux