On 11/15/24 09:16, Dmitry Baryshkov wrote:
On Wed, Nov 13, 2024 at 08:38:11AM +0100, Stefan Ekenberg wrote:AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1 while updating Audio InfoFrame information and then set to 0 when done. Otherwise partially updated Audio InfoFrames could be sent out. Two cases where this rule were not followed are fixed: - In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated before/after setting ADV7511_REG_AUDIO_INFOFRAME. - In audio_startup() use the correct register for clearing AUDIO_UPDATE bit. The problem with corrupted audio infoframes were discovered by letting a HDMI logic analyser check the output of ADV7535. Signed-off-by: Stefan Ekenberg <stefan.ekenberg@xxxxxxxx>Missing Fixes tag,
Ok, I will add Fixes tag.
--- drivers/gpu/drm/bridge/adv7511/adv7511_audio.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c index 61f4a38e7d2bf6905683cbc9e762b28ecc999d05..8f786592143b6c81e5a434768b51508d5e5f3c73 100644 --- a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c @@ -153,7 +153,16 @@ static int adv7511_hdmi_hw_params(struct device *dev, void *data, ADV7511_AUDIO_CFG3_LEN_MASK, len); regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG, ADV7511_I2C_FREQ_ID_CFG_RATE_MASK, rate << 4); - regmap_write(adv7511->regmap, 0x73, 0x1); + + /* send current Audio infoframe values while updating */ + regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE, + BIT(5), BIT(5)); + + regmap_write(adv7511->regmap, ADV7511_REG_AUDIO_INFOFRAME(0), 0x1); + + /* use Audio infoframe updated info */ + regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE, + BIT(5), 0);return 0;} @@ -184,8 +193,9 @@ static int audio_startup(struct device *dev, void *data) regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(0), BIT(7) | BIT(6), BIT(7)); /* use Audio infoframe updated info */ - regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(1), + regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE, BIT(5), 0);Should the REG_GC(1) still be written?
The comment before this line states "use Audio infoframe updated info" and, before my change, bit 5 of REG_GC(1) was cleared by the line I removed. Bit 5 is positioned within field GC_PP[3:0] and that field doesn't control audio infoframe and is read-only. My conclusion therefore was that the author if this code actually meant to clear bit 5 of REG_INFOFRAME_UPDATE from the very beginning. In short, clearing bit 5 of REG_GC(1) is invalid since it is a read-only field.
+ /* enable SPDIF receiver */ if (adv7511->audio_source == ADV7511_AUDIO_SOURCE_SPDIF) regmap_update_bits(adv7511->regmap, ADV7511_REG_AUDIO_CONFIG, --- base-commit: 59b723cd2adbac2a34fc8e12c74ae26ae45bf230 change-id: 20241108-adv7511-audio-info-frame-54614dd4bf57 Best regards, -- Stefan Ekenberg <stefan.ekenberg@xxxxxxxx>
