Quoting Dmitry Baryshkov (2024-10-31 15:54:49)
> On Thu, Oct 31, 2024 at 02:45:29PM -0700, Stephen Boyd wrote:
> > Quoting Dmitry Baryshkov (2024-10-31 11:42:36)
> > > On Tue, Oct 29, 2024 at 01:15:51PM -0700, Stephen Boyd wrote:
> >
> > Or use a displayport property that goes to connector node itself so that
> > we don't extend the graph binding of the usb-c-connector.
> >
> > cros-ec-typec {
> > usb-c-connector@0 {
> > altmodes {
> > displayport {
> > connector = <&dp_ml0_ml1>;
>
> I think this has been frowned upon. Not exactly this, but adding the
> displayport = <&foo>.
Do you have a pointer to that discussion? I'd like to understand the
reasoning.
>
> Thus it can only go to the swnode that is generated in software by the
> cros-ec driver.
I recall swnode as a way to sidestep figuring out the DT bindings for
usb typec. Where is this swnode being made? Somewhere inside the typec
framework?
>
> > };
> > };
> > port@1 {
> > endpoint@0 {
> > remote-endpoint = <&hub_ss0>;
> > };
> > };
> > };
> > usb-c-connector@1 {
> > altmodes {
> > displayport {
> > connector = <&dp_ml2_ml3>;
> > };
> > };
> > port@1 {
> > endpoint {
[....]
> >
> > >
> > > Maybe that's just it? Register DP_bridge (or QMP PHY) as
> > > orientation-switch? Then you don't need any extra API for the lane
> > > mapping? The cross-ec-typec can provide orientation information and the
> > > USB-C-aware controller will follow the lane mapping.
> >
> > I'm not really following but I don't think the DT binding discussed here
> > prevents that.
>
> I'm thinking about:
>
> it6505 {
> orientation-switch;
>
> ports {
> port@1 {
> it6505_dp_out: remote-endpoint = <&cros_ec_dp>;
> data-lanes = <0 1>;
> };
> };
> };
>
> cros-ec {
> port {
> cross_ec_dp: remote-endpoint = <&it6505_dp_out>;
> };
>
> connector@0 {
> reg = <0>;
> cros,dp-orientation = "normal";
>
> ports {
> // all USB HS and SS ports as usual;
> };
> };
>
> connector@1 {
> reg = <1>;
> cros,dp-orientation = "reverse";
>
> ports {
> // all USB HS and SS ports as usual;
> };
> };
>
> connector@2 {
> reg = <2>;
> cros,dp-orientation = "reverse";
>
> ports {
> // all USB HS and SS ports as usual;
> };
> };
>
> connector@3 {
> reg = <3>;
> cros,dp-orientation = "normal";
>
> ports {
> // all USB HS and SS ports as usual;
> };
> };
> };
>
> The cros-ec registers single drm bridge which will generate HPD events
> except on Trogdor, etc. At the same time, cros-ec requests the
> typec_switch_get(). When the cros-ec detects that the connector@N it
> being used for DP, it just generates corresponding typec_switch_set()
> call, setting the orientation of the it6505 (or QMP PHY). The rest can
> be handled either by EC's HPD code or by DP's HPD handler, the
> orientation should already be a correct one.
>
> So, yes. It requires adding the typec_switch_desc implementation _in_
> the it6505 (or in any other component which handles the 0-1 or 2-3
> selection). On the other hand as I wrote previously, the 0-1 / 2-3 is
> the USB-C functionality, not the DP one.
>
I don't think we should be adding typec code to pure display hardware
drivers like IT6505. To keep the driver focused on display stuff I
proposed implementing runtime lane assignment for drm_bridge chains
because DP has lanes. My understanding is that not all display
technologies have lanes, so implementing generic lane assignment
functionality is overkill/incorrect. DP has physical lanes in hardware
though, and those physical lanes are assigned to certain pins in the
type-c DP altmode spec, so it's not overkill to think about lanes when
the bridge is a DP bridge wired up to a type-c connector.
Long story short, I don't see how we can avoid _any_ lane assignment
logic in drm_bridge. The logic shouldn't walk the entire bridge chain,
but it should at least act on the bridge that is a DP bridge. I think
you're saying pretty much the same thing here, but you want the lane
remapping to be done via the typec layer whereas I want it to be done in
the drm_bridge layer. To me it looks out of place to add a
typec_switch_desc inside each DP drm_bridge because we duplicate the
logic about USB type-c DP altmode lane assignment to each DP bridge. A
DP bridge should just think about DP and not know or care about USB
type-c.
This is what's leading me to think we need some sort of lane assignment
capability at the DP connector. How that assignment flows from the DP
connector created in drm_bridge_connector.c to the hardware is where it
is less clear to me. Should that be implemented as a typec_switch_desc,
essentially out of band with drm_bridge, or as some drm_bridge_funcs
function similar to struct drm_bridge_funcs::hdmi_*()? If you look at
IT6505 in it6505_get_extcon_property() it actually wants to pull the
orientation of the type-c port with extcon_get_property(EXTCON_DISP_DP,
EXTCON_PROP_USB_TYPEC_POLARITY). Maybe pushing the orientation to the DP
bridge is backwards and we should be exposing this as some sort of
connector API that the drm_bridge can query whenever it wants.
What about ANX7625 where two DP lanes go to a cross-point switch before
leaving the chip on one of two pairs of lanes? This hardware is a DP
bridge smashed together with an orientation switch (typec_switch_desc)
so that you can simply wire the output pins up to a USB type-c connector
and support 2 lanes DP altmode. Qualcomm's QMP phy is quite similar.
Presumably we'd want the ANX driver to implement both a drm_bridge and a
typec_switch_desc if it was directly connected to a usb-c-connector
node. It's also interesting to think of the DT binding here, likely we
would have one output port in the ANX node's graph that represents the
combined DP and USB data that's connected to the SuperSpeed endpoint in
the usb-c-connector.
In the case where two lanes are wired to one USB type-c connector and
the other two lanes are wired to a different USB type-c connector it
would be odd to keep the typec_switch_desc and figure out a way to
mangle the lanes we want for a USB type-c connector by setting the
orientation of the typec_switch_desc. The chip isn't really acting as a
typec orientation control here because it isn't combining USB data and
DP data for a single USB type-c port. In fact, the type-c port has an
orientation and we actively don't want to tell the ANX7625 driver about
that port orientation because the orientation control is implemented
between the ANX part and the type-c connector by some redriver
controlled by the EC.
To satisfy all these cases it almost feels like we need to make the DP
connector have an "orientation", per your earlier DT snippet it would be
"reversed" or "normal", even though in hardware a DP connector has no
such concept because it can only be plugged in one way. All cases look
to be covered if we say that the drm_connector can have an orientation,
"normal" or "reversed", and we allow the bridge drivers to query that
whenever they want with some bridge/connector API. The typical case will
be that the orientation is normal, but we can make
drm_connector_oob_hotplug_event() change that to "reversed" when the
port is different.
This leaves us with the binding you propose above, and then some sort of
property that indicates the orientation of the DP connector. Instead of
being vendor specific I wonder if we can simply have a property like
"dp-reverse-orientation" in the connector node that the displayport.c
driver can look for to set the connector orientation to the reverse one
when DP altmode is entered on the port.
This is what I have:
it6505 {
ports {
port@1 {
it6505_dp_out: remote-endpoint = <&cros_ec_dp>;
data-lanes = <0 1>;
};
};
};
cros-ec {
port {
cross_ec_dp: remote-endpoint = <&it6505_dp_out>;
};
connector@0 {
reg = <0>;
ports {
// all USB HS and SS ports as usual;
};
};
connector@1 {
reg = <1>;
dp-reverse-orientation;
ports {
// all USB HS and SS ports as usual;
};
};
or ANX, swap out for it6505 node:
anx7625 {
ports {
port@1 {
anx7625_dp_out: remote-endpoint = <&cros_ec_dp>;
data-lanes = <0 1>;
};
};
};
and then a drm_bridge is created in cros-ec to terminate the bridge
chain. The displayport altmode driver will find the drm_bridge and the
drm_connector from the cros-ec node. When DP altmode is entered the
displayport altmode driver will set the drm_connector orientation based
on the presence of the dp-reverse-orientation property. We'll be able to
hook the hpd_notify() path in cros-ec by adding code to the drm_bridge
made there to do the HPD workaround. I'm not sure we need to use an
auxiliary device in this case, because it's a one-off solution for
cros-ec. And we don't even need to signal HPD from the cros-ec
drm_bridge because the oob_hotplug event will do it for us. If anything,
we need that displayport.c code to skip sending the hotplug event when
"no-hpd" is present in the cros-ec node. Note, this works for any number
of usb-c-connector nodes. And finally, DP bridges like IT6505 don't need
to implement a typec_switch_desc, they can simply support flipping the
orientation by querying the drm_connector for the bridge chain when they
see fit. ANX7625 can support that as well when it doesn't see the
'orientation-switch' property.
Did I miss anything? I suspect a drm_connector having an orientation is
the most controversial part of this proposal.
