Hi Benoit,
On 03/09/2013 16:55, Benoit Parrot wrote:
Hi,
I have not received any feedback on this patch.
It has been pending since the end of June (first post).
Can I get an estimate when it will be included/accepted?
It looks good to me beside a minor comment below.
Could you just rebase it on my lastest
git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git
for_3.13/dts branch because it conflicts with the cleanup done by Javier.
On Fri, Aug 23, 2013 at 11:13:56AM -0500, Benoit Parrot wrote:
Add LCDC device node in DT for am33xx
Add LCDC and Panel info in DT for am335x-evm
Changes in v3:
- rebase to 3.11-rc6
Changes in v2:
- remove redundant/unnecessary SoC specific setting in the board dts
Signed-off-by: Benoit Parrot <bparrot@xxxxxx>
---
arch/arm/boot/dts/am335x-evm.dts | 72 ++++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/am33xx.dtsi | 9 +++++
2 files changed, 81 insertions(+)
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index 3aee1a4..b0703f1 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -149,6 +149,40 @@
0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
>;
};
+
+ lcd_pins_s0: lcd_pins_s0 {
+ pinctrl-single,pins = <
+ 0x20 0x01 /* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */
+ 0x24 0x01 /* gpmc_ad9.lcd_data17, OUTPUT | MODE1 */
+ 0x28 0x01 /* gpmc_ad10.lcd_data18, OUTPUT | MODE1 */
+ 0x2c 0x01 /* gpmc_ad11.lcd_data19, OUTPUT | MODE1 */
+ 0x30 0x01 /* gpmc_ad12.lcd_data20, OUTPUT | MODE1 */
+ 0x34 0x01 /* gpmc_ad13.lcd_data21, OUTPUT | MODE1 */
+ 0x38 0x01 /* gpmc_ad14.lcd_data22, OUTPUT | MODE1 */
+ 0x3c 0x01 /* gpmc_ad15.lcd_data23, OUTPUT | MODE1 */
+ 0xa0 0x00 /* lcd_data0.lcd_data0, OUTPUT | MODE0 */
+ 0xa4 0x00 /* lcd_data1.lcd_data1, OUTPUT | MODE0 */
+ 0xa8 0x00 /* lcd_data2.lcd_data2, OUTPUT | MODE0 */
+ 0xac 0x00 /* lcd_data3.lcd_data3, OUTPUT | MODE0 */
+ 0xb0 0x00 /* lcd_data4.lcd_data4, OUTPUT | MODE0 */
+ 0xb4 0x00 /* lcd_data5.lcd_data5, OUTPUT | MODE0 */
+ 0xb8 0x00 /* lcd_data6.lcd_data6, OUTPUT | MODE0 */
+ 0xbc 0x00 /* lcd_data7.lcd_data7, OUTPUT | MODE0 */
+ 0xc0 0x00 /* lcd_data8.lcd_data8, OUTPUT | MODE0 */
+ 0xc4 0x00 /* lcd_data9.lcd_data9, OUTPUT | MODE0 */
+ 0xc8 0x00 /* lcd_data10.lcd_data10, OUTPUT | MODE0 */
+ 0xcc 0x00 /* lcd_data11.lcd_data11, OUTPUT | MODE0 */
+ 0xd0 0x00 /* lcd_data12.lcd_data12, OUTPUT | MODE0 */
+ 0xd4 0x00 /* lcd_data13.lcd_data13, OUTPUT | MODE0 */
+ 0xd8 0x00 /* lcd_data14.lcd_data14, OUTPUT | MODE0 */
+ 0xdc 0x00 /* lcd_data15.lcd_data15, OUTPUT | MODE0 */
+ 0xe0 0x00 /* lcd_vsync.lcd_vsync, OUTPUT | MODE0 */
+ 0xe4 0x00 /* lcd_hsync.lcd_hsync, OUTPUT | MODE0 */
+ 0xe8 0x00 /* lcd_pclk.lcd_pclk, OUTPUT | MODE0 */
+ 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */
+ >;
+ };
+
};
ocp {
@@ -311,6 +345,10 @@
};
};
};
+
+ lcdc: lcdc@4830e000 {
+ status = "okay";
+ };
};
vbat: fixedregulator@0 {
@@ -374,6 +412,40 @@
brightness-levels = <0 51 53 56 62 75 101 152 255>;
default-brightness-level = <8>;
};
+
+ panel {
+ compatible = "ti,tilcdc,panel";
Nit: There are a lots of TI here :-)
Could you just name it: ti,lcdc,panel ?
Thanks,
Benoit
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
