MIPI DSI:
- Add "vsys_lcm_reg" regulator support and setup the "mt6357_vsim1_reg",
to power the pannel plugged to the DSI connector.
- Setup the Display Parallel Interface.
- Add the startek kd070fhfid015 pannel support.
HDMI:
- Add HDMI connector support.
- Add the "ite,it66121" HDMI bridge support, driven by I2C1.
- Setup the Display Parallel Interface.
Signed-off-by: Alexandre Mergnat <amergnat@xxxxxxxxxxxx>
---
arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 182 ++++++++++++++++++++++++++++
1 file changed, 182 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
index 50cbaefa1a99..4afdcbefc481 100644
--- a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
@@ -26,6 +26,18 @@ chosen {
stdout-path = "serial0:921600n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+ type = "d";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_connector_out>;
+ };
+ };
+ };
+
firmware {
optee {
compatible = "linaro,optee-tz";
@@ -86,6 +98,56 @@ optee_reserved: optee@43200000 {
reg = <0 0x43200000 0 0x00c00000>;
};
};
+
+ vsys_lcm_reg: regulator-vsys-lcm {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&pio 129 GPIO_ACTIVE_HIGH>;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "vsys_lcm";
+ };
+};
+
+&dpi0 {
+ pinctrl-0 = <&dpi_default_pins>;
+ pinctrl-1 = <&dpi_idle_pins>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+
+ port {
+ dpi_out: endpoint {
+ remote-endpoint = <&it66121_in>;
+ };
+ };
+};
+
+&dsi0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ panel@0 {
+ compatible = "startek,kd070fhfid015";
+ status = "okay";
+ reg = <0>;
+ enable-gpios = <&pio 67 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
+ iovcc-supply = <&mt6357_vsim1_reg>;
+ power-supply = <&vsys_lcm_reg>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
+
+ port {
+ dsi_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
};
&cpu0 {
@@ -138,6 +200,50 @@ &i2c0 {
status = "okay";
};
+&i2c1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-div = <2>;
+ clock-frequency = <100000>;
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ it66121hdmitx: it66121hdmitx@4c {
+ #sound-dai-cells = <0>;
+ compatible = "ite,it66121";
+ interrupt-parent = <&pio>;
+ interrupts = <68 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&ite_pins>;
+ pinctrl-names = "default";
+ reg = <0x4c>;
+ reset-gpios = <&pio 69 GPIO_ACTIVE_LOW>;
+ vcn18-supply = <&mt6357_vsim2_reg>;
+ vcn33-supply = <&mt6357_vibr_reg>;
+ vrf12-supply = <&mt6357_vrf12_reg>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ it66121_in: endpoint {
+ bus-width = <12>;
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ hdmi_connector_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
+};
+
&mmc0 {
assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>;
assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
@@ -180,7 +286,55 @@ &mt6357_pmic {
#interrupt-cells = <2>;
};
+&mt6357_vsim1_reg {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+};
+
&pio {
+ dpi_default_pins: dpi-default-pins {
+ pins {
+ pinmux = <MT8365_PIN_0_GPIO0__FUNC_DPI_D0>,
+ <MT8365_PIN_1_GPIO1__FUNC_DPI_D1>,
+ <MT8365_PIN_2_GPIO2__FUNC_DPI_D2>,
+ <MT8365_PIN_3_GPIO3__FUNC_DPI_D3>,
+ <MT8365_PIN_4_GPIO4__FUNC_DPI_D4>,
+ <MT8365_PIN_5_GPIO5__FUNC_DPI_D5>,
+ <MT8365_PIN_6_GPIO6__FUNC_DPI_D6>,
+ <MT8365_PIN_7_GPIO7__FUNC_DPI_D7>,
+ <MT8365_PIN_8_GPIO8__FUNC_DPI_D8>,
+ <MT8365_PIN_9_GPIO9__FUNC_DPI_D9>,
+ <MT8365_PIN_10_GPIO10__FUNC_DPI_D10>,
+ <MT8365_PIN_11_GPIO11__FUNC_DPI_D11>,
+ <MT8365_PIN_12_GPIO12__FUNC_DPI_DE>,
+ <MT8365_PIN_13_GPIO13__FUNC_DPI_VSYNC>,
+ <MT8365_PIN_14_GPIO14__FUNC_DPI_CK>,
+ <MT8365_PIN_15_GPIO15__FUNC_DPI_HSYNC>;
+ drive-strength = <MTK_DRIVE_4mA>;
+ };
+ };
+
+ dpi_idle_pins: dpi-idle-pins {
+ pins {
+ pinmux = <MT8365_PIN_0_GPIO0__FUNC_GPIO0>,
+ <MT8365_PIN_1_GPIO1__FUNC_GPIO1>,
+ <MT8365_PIN_2_GPIO2__FUNC_GPIO2>,
+ <MT8365_PIN_3_GPIO3__FUNC_GPIO3>,
+ <MT8365_PIN_4_GPIO4__FUNC_GPIO4>,
+ <MT8365_PIN_5_GPIO5__FUNC_GPIO5>,
+ <MT8365_PIN_6_GPIO6__FUNC_GPIO6>,
+ <MT8365_PIN_7_GPIO7__FUNC_GPIO7>,
+ <MT8365_PIN_8_GPIO8__FUNC_GPIO8>,
+ <MT8365_PIN_9_GPIO9__FUNC_GPIO9>,
+ <MT8365_PIN_10_GPIO10__FUNC_GPIO10>,
+ <MT8365_PIN_11_GPIO11__FUNC_GPIO11>,
+ <MT8365_PIN_12_GPIO12__FUNC_GPIO12>,
+ <MT8365_PIN_13_GPIO13__FUNC_GPIO13>,
+ <MT8365_PIN_14_GPIO14__FUNC_GPIO14>,
+ <MT8365_PIN_15_GPIO15__FUNC_GPIO15>;
+ };
+ };
+
ethernet_pins: ethernet-pins {
phy_reset_pins {
pinmux = <MT8365_PIN_133_TDM_TX_DATA1__FUNC_GPIO133>;
@@ -222,6 +376,34 @@ pins {
};
};
+ i2c1_pins: i2c1-pins {
+ pins {
+ pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>,
+ <MT8365_PIN_60_SCL1__FUNC_SCL1_0>;
+ bias-pull-up;
+ };
+ };
+
+ ite_pins: ite-pins {
+
+ irq_ite_pins {
+ pinmux = <MT8365_PIN_68_CMDAT0__FUNC_GPIO68>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ pwr_pins {
+ pinmux = <MT8365_PIN_70_CMDAT2__FUNC_GPIO70>,
+ <MT8365_PIN_71_CMDAT3__FUNC_GPIO71>;
+ output-high;
+ };
+
+ rst_ite_pins {
+ pinmux = <MT8365_PIN_69_CMDAT1__FUNC_GPIO69>;
+ output-high;
+ };
+ };
+
mmc0_default_pins: mmc0-default-pins {
clk-pins {
pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>;
--
2.25.1
