The Chroma Down Sampling (CDM) block is a hardware component in the DPU pipeline that includes a CSC block capable of converting RGB input from the DPU to YUV data. This block can be used with either HDMI, DP, or writeback interfaces. This series adds support for the CDM block to be used with DP in YUV420 mode format. This series allows selection of the YUV420 format for monitors which support certain resolutions only in YUV420 thus unblocking the validation of many other resolutions which were previously filtered out if the connector did not support YUV420. This was validated using a DP connected monitor requiring the use of YUV420 format. This series is dependent on [1], [2], and [3]: [1] https://patchwork.freedesktop.org/series/118831/ [2] https://patchwork.freedesktop.org/series/129395/ [3] https://patchwork.freedesktop.org/series/129864/ Changes in v4: - Use dp_utils_pack_sdp_header() to pack the SDP header and parity bytes into a buffer - Use this buffer when writing the VSC SDP data in dp_catalog_panel_send_vsc_sdp() and write to all the MMSS_DP_GENERIC0 registers - Clear up that DP_MAINLINK_CTRL_FLUSH_MODE register requires the use of bits [24:23] - Modify certain macros to explicitly set their values in the bits of DP_MAINLINK_CTRL_FLUSH_MODE_MASK - Remove hw_cdm check in dpu_encoder_needs_periph_flush() and dpu_encoder_phys_vid_enable() Changes in v3: - Change ordering of the header byte macros in dp_utils.h - Create a new struct, msm_dp_sdp_with_parity - Utilize drm_dp_vsc_sdp_pack() from a new added dependency of series [3] to pack the VSC SDP data into the new msm_dp_sdp_with_parity struct instead of packing only for YUV420 - Modify dp_catalog_panel_send_vsc_sdp() so that it sends the VSC SDP data using the new msm_dp_sdp_with_parity struct - Clear up that the DP_MAINLINK_FLUSH_MODE_SDE_PERIPH_UPDATE macro is setting multiple bits and not just one - Move the connector's ycbcr_420_allowed parameter so it is no longer dependent on if the dp_display is not eDP Changes in v2: - Minor formatting changes throughout - Move 'fixes' patch to the top - Move VSC SDP support check API from dp_panel.c to drm_dp_helper.c - Create a separate patch for modifying the dimensions for CDM setup to be non-WB specific - Remove a patch that modified the INTF_CONFIG2 register in favor of having this series be dependent on [2] - Separate configuration ctrl programming from clock related programming into two patches - Add a VSC SDP check in dp_bridge_mode_valid() - Move parity calculation functions to new files dp_utils.c and dp_utils.h - Remove dp_catalog_hw_revision() changes and utilize the original version of the function when checking the DP hardware version - Create separate packing and programming functions for the VSC SDP - Make the packing header bytes function generic so it can be used with dp_audio.c - Create two separate enable/disable VSC SDP functions instead of having one with the ability to do both - Move timing engine programming to a separate patch from original encoder programming patch - Move update_pending_flush_periph() code to be in the same patch as the encoder programming - Create new API's to check if the dpu encoder needs a peripheral flush - Allow YUV420 modes for the DP connector when there's a CDM block available instead of checking if VSC SDP is supported Kuogee Hsieh (1): drm/msm/dpu: add support of new peripheral flush mechanism Paloma Arellano (18): drm/msm/dpu: allow certain formats for CDM for DP drm/msm/dpu: add division of drm_display_mode's hskew parameter drm/msm/dpu: pass mode dimensions instead of fb size in CDM setup drm/msm/dpu: allow dpu_encoder_helper_phys_setup_cdm to work for DP drm/msm/dpu: move dpu_encoder_helper_phys_setup_cdm to dpu_encoder drm/msm/dp: rename wide_bus_en to wide_bus_supported drm/msm/dp: store mode YUV420 information to be used by rest of DP drm/msm/dp: check if VSC SDP is supported in DP programming drm/msm/dpu: move widebus logic to its own API drm/msm/dp: program config ctrl for YUV420 over DP drm/msm/dp: change clock related programming for YUV420 over DP drm/msm/dp: move parity calculation to dp_utils drm/msm/dp: add VSC SDP support for YUV420 over DP drm/msm/dp: enable SDP and SDE periph flush update drm/msm/dpu: modify encoder programming for CDM over DP drm/msm/dpu: modify timing engine programming for YUV420 over DP drm/msm/dpu: reserve CDM blocks for DP if mode is YUV420 drm/msm/dp: allow YUV420 mode for DP connector when CDM available drivers/gpu/drm/msm/Makefile | 3 +- drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 164 +++++++++++++++--- drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.h | 4 + .../gpu/drm/msm/disp/dpu1/dpu_encoder_phys.h | 26 ++- .../drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 30 +++- .../drm/msm/disp/dpu1/dpu_encoder_phys_wb.c | 100 +---------- drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.c | 2 +- drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c | 17 ++ drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h | 10 ++ drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 4 +- drivers/gpu/drm/msm/dp/dp_audio.c | 101 ++--------- drivers/gpu/drm/msm/dp/dp_catalog.c | 129 +++++++++++++- drivers/gpu/drm/msm/dp/dp_catalog.h | 10 +- drivers/gpu/drm/msm/dp/dp_ctrl.c | 17 +- drivers/gpu/drm/msm/dp/dp_display.c | 82 ++++++--- drivers/gpu/drm/msm/dp/dp_drm.c | 6 +- drivers/gpu/drm/msm/dp/dp_drm.h | 3 +- drivers/gpu/drm/msm/dp/dp_panel.c | 56 ++++++ drivers/gpu/drm/msm/dp/dp_panel.h | 2 + drivers/gpu/drm/msm/dp/dp_reg.h | 9 + drivers/gpu/drm/msm/dp/dp_utils.c | 129 ++++++++++++++ drivers/gpu/drm/msm/dp/dp_utils.h | 26 +++ drivers/gpu/drm/msm/msm_drv.h | 22 ++- 23 files changed, 711 insertions(+), 241 deletions(-) create mode 100644 drivers/gpu/drm/msm/dp/dp_utils.c create mode 100644 drivers/gpu/drm/msm/dp/dp_utils.h -- 2.39.2
