Hi Frieder
On Thu, Dec 7, 2023 at 5:58 PM Frieder Schrempf
<frieder.schrempf@xxxxxxxxxx> wrote:
>
> On 07.12.23 15:16, Dario Binacchi wrote:
> > The patch completes the setting of CLKLANE_STOP for the imx8mn and imx8mp
> > platforms (i. e. not exynos).
>
> This also affects i.MX8MM, so better just mention i.MX in general in the
> commit message.
>
> >
> > Co-developed-by: Michael Trimarchi <michael@xxxxxxxxxxxxxxxxxxxx>
> > Signed-off-by: Michael Trimarchi <michael@xxxxxxxxxxxxxxxxxxxx>
> > Signed-off-by: Dario Binacchi <dario.binacchi@xxxxxxxxxxxxxxxxxxxx>
> > ---
> >
> > (no changes since v1)
> >
> > drivers/gpu/drm/bridge/samsung-dsim.c | 7 ++++++-
> > 1 file changed, 6 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/gpu/drm/bridge/samsung-dsim.c b/drivers/gpu/drm/bridge/samsung-dsim.c
> > index 15bf05b2bbe4..13f181c99d7e 100644
> > --- a/drivers/gpu/drm/bridge/samsung-dsim.c
> > +++ b/drivers/gpu/drm/bridge/samsung-dsim.c
> > @@ -96,6 +96,7 @@
> > #define DSIM_MFLUSH_VS BIT(29)
> > /* This flag is valid only for exynos3250/3472/5260/5430 */
> > #define DSIM_CLKLANE_STOP BIT(30)
> > +#define DSIM_NON_CONTINUOUS_CLKLANE BIT(31)
> >
> > /* DSIM_ESCMODE */
> > #define DSIM_TX_TRIGGER_RST BIT(4)
> > @@ -945,8 +946,12 @@ static int samsung_dsim_init_link(struct samsung_dsim *dsi)
> > * power consumption.
> > */
> > if (driver_data->has_clklane_stop &&
> > - dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS)
> > + dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS) {
> > + if (!samsung_dsim_hw_is_exynos(dsi->plat_data->hw_type))
> > + reg |= DSIM_NON_CONTINUOUS_CLKLANE;
> > +
> > reg |= DSIM_CLKLANE_STOP;
> > + }
>
> I really wonder what the difference between DSIM_NON_CONTINUOUS_CLKLANE
> and DSIM_CLKLANE_STOP is.
>
> If Exynos only has the latter, it's pretty clear what to use. But as
> i.MX has both of these bits, should both be set? Or is setting
> DSIM_NON_CONTINUOUS_CLKLANE enough and we should leave DSIM_CLKLANE_STOP
> alone?
>
We add the DSIM_NON_CONTINUOUS_CLKLANE because there was a similar
commit in NXP bsp.
Now according to the datasheet the DSIM_NON_CONTINUOUS_CLKLANE should
be the right bit.
NXP guys should clarify then a bit
Michael
> Maybe someone has a clue here. The description of the bits in the RM is:
>
> DSIM_NON_CONTINUOUS_CLKLANE - Non-continuous clock mode
> DSIM_CLKLANE_STOP - PHY clock lane On/Off for ESD
>
> > samsung_dsim_write(dsi, DSIM_CONFIG_REG, reg);
> >
> > lanes_mask = BIT(dsi->lanes) - 1;
