On Fri, Sep 15, 2023 at 04:05:15PM +0200, Flavio Suligoi wrote: > The Monolithic Power (MPS) MP3309C is a WLED step-up converter, featuring a > programmable switching frequency to optimize efficiency. > The brightness can be controlled either by I2C commands (called "analog" > mode) or by a PWM input signal (PWM mode). > This driver supports both modes. > > For device driver details, please refer to: > - drivers/video/backlight/mp3309c_bl.c > > The datasheet is available at: > - https://www.monolithicpower.com/en/mp3309c.html > > Signed-off-by: Flavio Suligoi <f.suligoi@xxxxxxx> > --- > > v2: > - remove useless properties (dimming-mode, pinctrl-names, pinctrl-0, > switch-on-delay-ms, switch-off-delay-ms, reset-gpios, reset-on-delay-ms, > reset-on-length-ms) > - add common.yaml# > - remove already included properties (default-brightness, max-brightness) > - substitute three boolean properties, used for the overvoltage-protection > values, with a single enum property > - remove some conditional definitions > - remove the 2nd example > v1: > - first version > > .../bindings/leds/backlight/mps,mp3309c.yaml | 73 +++++++++++++++++++ > 1 file changed, 73 insertions(+) > create mode 100644 Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml > > diff --git a/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml b/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml > new file mode 100644 > index 000000000000..99ccdba2c08f > --- /dev/null > +++ b/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml > @@ -0,0 +1,73 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/leds/backlight/mps,mp3309c.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: MPS MP3309C backlight > + > +maintainers: > + - Flavio Suligoi <f.suligoi@xxxxxxx> > + > +description: | > + The Monolithic Power (MPS) MP3309C is a WLED step-up converter, featuring a > + programmable switching frequency to optimize efficiency. > + It supports two different dimming modes: > + > + - analog mode, via I2C commands (default) > + - PWM controlled mode. > + > + The datasheet is available at: > + https://www.monolithicpower.com/en/mp3309c.html > + > +allOf: > + - $ref: common.yaml# > + > +properties: > + compatible: > + const: mps,mp3309c > + > + reg: > + maxItems: 1 > + > + pwms: > + description: if present, the backlight is controlled in PWM mode. > + maxItems: 1 > + > + enable-gpios: > + description: GPIO used to enable the backlight in "analog-i2c" dimming mode. > + maxItems: 1 > + > + mps,overvoltage-protection-microvolt: > + description: Overvoltage protection (13.5V, 24V or 35.5V). If missing, the > + hardware default of 35.5V is used. default: 35500000 instead of prose saying the same thing. With that, Reviewed-by: Rob Herring <robh@xxxxxxxxxx> > + enum: [ 13500000, 24000000, 35500000 ] > + > + mps,no-sync-mode: > + description: disable synchronous rectification mode > + type: boolean > + > +required: > + - compatible > + - reg > + - max-brightness > + - default-brightness > + > +unevaluatedProperties: false > + > +examples: > + - | > + i2c { > + #address-cells = <1>; > + #size-cells = <0>; > + > + /* Backlight with PWM control */ > + backlight_pwm: backlight@17 { > + compatible = "mps,mp3309c-backlight"; > + reg = <0x17>; > + pwms = <&pwm1 0 3333333 0>; /* 300 Hz --> (1/f) * 1*10^9 */ > + max-brightness = <100>; > + default-brightness = <80>; > + overvoltage-protection-microvolt = <24000000>; > + }; > + }; > -- > 2.34.1 >
