XPI-3128 is RK3128 based SBC form Geniatec in RPi form factor
Specs:
- Rockchip RK3128
- 1 GB DDR3 DRAM
- 8/16 GB eMMC
- TF card slot
- 100 MBit ethernet / RJ45
- optional Marvell 88W8897 (USB version)
- 3 x USB host (onboard GL852G hub connected to SoC ehci host)
- 1 x USB otg
- 1 x Type-C (solely for powering the board)
- HDMI 1.4 out
- 1 ADC button
- IR receiver
- Artasie AM1805 RTC
- 40 pin header
Signed-off-by: Alex Bee <knaerzche@xxxxxxxxx>
---
arch/arm/boot/dts/rockchip/Makefile | 1 +
.../arm/boot/dts/rockchip/rk3128-xpi-3128.dts | 431 ++++++++++++++++++
2 files changed, 432 insertions(+)
create mode 100644 arch/arm/boot/dts/rockchip/rk3128-xpi-3128.dts
diff --git a/arch/arm/boot/dts/rockchip/Makefile b/arch/arm/boot/dts/rockchip/Makefile
index 0f46e18fe275..58868cf0510b 100644
--- a/arch/arm/boot/dts/rockchip/Makefile
+++ b/arch/arm/boot/dts/rockchip/Makefile
@@ -10,6 +10,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3066a-mk808.dtb \
rk3066a-rayeager.dtb \
rk3128-evb.dtb \
+ rk3128-xpi-3128.dtb \
rk3188-bqedison2qc.dtb \
rk3188-px3-evb.dtb \
rk3188-radxarock.dtb \
diff --git a/arch/arm/boot/dts/rockchip/rk3128-xpi-3128.dts b/arch/arm/boot/dts/rockchip/rk3128-xpi-3128.dts
new file mode 100644
index 000000000000..842b5f20d98a
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rk3128-xpi-3128.dts
@@ -0,0 +1,431 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "rk3128.dtsi"
+
+/ {
+ model = "Geniatech XPI-3128";
+ compatible = "geniatech,xpi-3128", "rockchip,rk3128";
+
+ aliases {
+ ethernet0 = &gmac;
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ gpio3 = &gpio3;
+ mmc0 = &emmc;
+ mmc1 = &sdmmc;
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ adc-keys {
+ compatible = "adc-keys";
+ io-channels = <&saradc 1>;
+ io-channel-names = "buttons";
+ keyup-threshold-microvolt = <3300000>;
+
+ button-recovery {
+ label = "Recovery";
+ linux,code = <KEY_VENDOR>;
+ press-threshold-microvolt = <0>;
+ };
+ };
+
+ dc_5v: dc-5v-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "DC_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /*
+ * This is a vbus-supply, which also supplies the GL852G usb hub,
+ * thus has to be always-on
+ */
+ host_pwr_5v: host-pwr-5v-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio3 RK_PC4 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <1500>;
+ regulator-name = "HOST_PWR_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_5v>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_drv>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio3 RK_PD2 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_int>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-power {
+ gpios = <&gpio0 RK_PD2 GPIO_ACTIVE_HIGH>;
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_BLUE>;
+ default-state = "on";
+ pinctrl-names = "default";
+ pinctrl-0 = <&power_led>;
+ };
+
+ led-spd {
+ gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
+ function = LED_FUNCTION_LAN;
+ color = <LED_COLOR_ID_GREEN>;
+ /*
+ * currently not allowed to be set as per
+ * https://www.kernel.org/doc/Documentation/devicetree/bindings/leds/common.yaml
+ * and has to set in userspace
+ *
+ * linux,default-trigger = "netdev";
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&spd_led>;
+ };
+ };
+
+ mcu3v3: mcu3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "MCU3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_io>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_ddr: vcc-ddr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_DDR";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ vin-supply = <&vcc_sys>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_io: vcc-io-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_IO";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_sys>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_lan: vcc-lan-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_LAN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_io>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_sd: vcc-sd-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio1 RK_PB6 GPIO_ACTIVE_LOW>;
+ startup-delay-us = <500>;
+ regulator-name = "VCC_SD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_io>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_pwren>;
+ };
+
+ vcc_sys: vcc-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_SYS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_5v>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc33_hdmi: vcc33-hdmi-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC33_HDMI";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcca_33>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcca_33: vcca-33-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VCCA_33";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_sys>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_11: vdd-11-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_11";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ vin-supply = <&vcc_sys>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd11_hdmi: vdd11-hdmi-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD11_HDMI";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ vin-supply = <&vdd_11>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_arm: vdd-arm-regulator {
+ compatible = "pwm-regulator";
+ regulator-name = "VDD_ARM";
+ pwms = <&pwm1 0 25000 1>;
+ pwm-supply = <&vcc_sys>;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /*
+ * As per schematics vdd_log is minimum 900 mV, maximum 1400 mV.
+ * Since there are HW blocks in PD_LOGIC which are all driven by
+ * this supply, which either do not have a driver at all or the
+ * driver does not have regulator support, but are required for
+ * the board to run we have to make sure here, that the voltage
+ * never drops below 1050 mV.
+ */
+ vdd_log: vdd-log-regulator {
+ compatible = "pwm-regulator";
+ regulator-name = "VDD_LOG";
+ pwms = <&pwm2 0 25000 1>;
+ pwm-dutycycle-range = <30 100>;
+ pwm-supply = <&vcc_sys>;
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-ramp-delay = <4000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ memory@60000000 {
+ device_type = "memory";
+ reg = <0x60000000 0x40000000>;
+ };
+
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+ bus-width = <8>;
+ vmmc-supply = <&vcc_io>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ cap-mmc-highspeed;
+ no-sd;
+ no-sdio;
+ status = "okay";
+};
+
+&gmac {
+ clock_in_out = "output";
+ phy-supply = <&vcc_lan>;
+ phy-mode = "rmii";
+ phy-handle = <&phy0>;
+ assigned-clocks = <&cru SCLK_MAC_SRC>;
+ assigned-clock-rates= <50000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rmii_pins>;
+ status = "okay";
+};
+
+/*
+ * Add labels for each pin which is exposed at the 40-pin header
+ */
+&gpio0 {
+ gpio-line-names = /* GPIO0 A0-A7 */
+ "", "", "HEADER_5", "HEADER_3",
+ "", "", "", "",
+ /* GPIO0 B0-B7 */
+ "HEADER_22", "HEADER_23", "", "HEADER_19",
+ "HEADER_26", "HEADER_21", "HEADER_24", "",
+ /* GPIO0 C0-C7 */
+ "", "HEADER_18", "", "",
+ "", "", "", "",
+ /* GPIO0 D0-D7 */
+ "HEADER_36", "", "", "",
+ "", "", "HEADER_13", "";
+};
+
+&gpio1 {
+ gpio-line-names = /* GPIO1 A0-A7 */
+ "HEADER_7", "HEADER_35", "HEADER_33", "HEADER_37",
+ "HEADER_40", "HEADER_38", "", "",
+ /* GPIO1 B0-B7 */
+ "HEADER_11", "", "", "HEADER_29",
+ "HEADER_31", "", "", "",
+ /* GPIO1 C0-C7 */
+ "", "", "", "",
+ "", "", "", "",
+ /* GPIO1 D0-D7 */
+ "", "", "", "",
+ "", "", "", "";
+};
+
+&gpio2 {
+ gpio-line-names = /* GPIO2 A0-A7 */
+ "", "", "", "",
+ "", "", "", "",
+ /* GPIO2 B0-B7 */
+ "", "", "", "",
+ "", "", "", "",
+ /* GPIO2 C0-C7 */
+ "", "", "", "",
+ "HEADER_27", "", "", "",
+ /* GPIO2 D0-D7 */
+ "", "", "HEADER_8", "HEADER_10",
+ "", "", "", "";
+};
+
+&gpio3 {
+ gpio-line-names = /* GPIO3 A0-A7 */
+ "", "", "", "",
+ "", "", "", "",
+ /* GPIO3 B0-B7 */
+ "", "", "", "",
+ "", "", "", "",
+ /* GPIO3 C0-C7 */
+ "", "HEADER_32", "", "",
+ "", "", "", "HEADER_12",
+ /* GPIO3 D0-D7 */
+ "", "", "", "HEADER_15",
+ "", "", "", "";
+};
+
+&gpu {
+ mali-supply = <&vdd_log>;
+ status = "okay";
+};
+
+&mdio {
+ phy0: ethernet-phy@1 {
+ /* DP83848C interrupt is not connected */
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ max-speed = <100>;
+ reset-assert-us = <15000>;
+ reset-deassert-us = <80000>;
+ reset-gpios = <&gpio2 RK_PD0 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dp83848c_rst>;
+ };
+};
+
+&pinctrl {
+ dp83848c {
+ dp83848c_rst: dp83848c-rst {
+ rockchip,pins = <2 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ ir-receiver {
+ ir_int: ir-int {
+ rockchip,pins = <3 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ power_led: power-led {
+ rockchip,pins = <0 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ spd_led: spd-led {
+ rockchip,pins = <3 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb2 {
+ host_drv: host-drv {
+ rockchip,pins = <3 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc_io>;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ vmmc-supply = <&vcc_sd>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_bus4 &sdmmc_clk &sdmmc_cmd &sdmmc_det>;
+ cap-sd-highspeed;
+ no-mmc;
+ no-sdio;
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb_host_ehci {
+ status = "okay";
+};
+
+&usb_otg {
+ vusb_a-supply = <&vcc_io>;
+ vusb_d-supply = <&vdd_11>;
+ status = "okay";
+};
+
+&usb2phy {
+ status = "okay";
+};
+
+&usb2phy_host {
+ status = "okay";
+};
+
+&usb2phy_otg {
+ status = "okay";
+};
--
2.42.0
