Re: [PATCH v1 2/2] backlight: mp3309c: Add support for MPS MP3309C

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 29/08/2023 12:15, Flavio Suligoi wrote:
> The Monolithic Power (MPS) MP3309C is a WLED step-up converter, featuring a
> programmable switching frequency to optimize efficiency.
> The brightness can be controlled either by I2C commands (called "analog"
> mode) or by a PWM input signal (PWM mode).
> This driver supports both modes.
> 
> For DT configuration details, please refer to:
> - Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
> 
> The datasheet is available at:
> - https://www.monolithicpower.com/en/mp3309c.html
> 
> Signed-off-by: Flavio Suligoi <f.suligoi@xxxxxxx>
> ---
>  MAINTAINERS                          |   6 +
>  drivers/video/backlight/Kconfig      |  13 +
>  drivers/video/backlight/Makefile     |   1 +
>  drivers/video/backlight/mp3309c_bl.c | 491 +++++++++++++++++++++++++++
>  4 files changed, 511 insertions(+)
>  create mode 100644 drivers/video/backlight/mp3309c_bl.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 3be1bdfe8ecc..895c56ff4f1e 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -14333,6 +14333,12 @@ S:	Maintained
>  F:	Documentation/driver-api/tty/moxa-smartio.rst
>  F:	drivers/tty/mxser.*
>  
> +MP3309C BACKLIGHT DRIVER
> +M:	Flavio Suligoi <f.suligoi@xxxxxxx>
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
> +F:	drivers/video/backlight/mp3309c_bl.c
> +
>  MR800 AVERMEDIA USB FM RADIO DRIVER
>  M:	Alexey Klimov <klimov.linux@xxxxxxxxx>
>  L:	linux-media@xxxxxxxxxxxxxxx
> diff --git a/drivers/video/backlight/Kconfig b/drivers/video/backlight/Kconfig
> index 51387b1ef012..65d0ac9f611d 100644
> --- a/drivers/video/backlight/Kconfig
> +++ b/drivers/video/backlight/Kconfig
> @@ -389,6 +389,19 @@ config BACKLIGHT_LM3639
>  	help
>  	  This supports TI LM3639 Backlight + 1.5A Flash LED Driver
>  
> +config BACKLIGHT_MP3309C

Why is this placed between LM and LP entries? Keep things ordered.

> +	tristate "Backlight Driver for MPS MP3309C"
> +	depends on I2C
> +	select REGMAP_I2C
> +	select NEW_LEDS
> +	select LEDS_CLASS
> +	help
> +	  This supports MPS MP3309C backlight WLED Driver in both PWM and
> +	  analog/I2C dimming modes.
> +
> +	  To compile this driver as a module, choose M here: the module will
> +	  be called mp3309c_bl.
> +
>  config BACKLIGHT_LP855X


>  	tristate "Backlight driver for TI LP855X"
>  	depends on I2C && PWM
> diff --git a/drivers/video/backlight/Makefile b/drivers/video/backlight/Makefile
> index f72e1c3c59e9..c42c5bccc5ac 100644
> --- a/drivers/video/backlight/Makefile
> +++ b/drivers/video/backlight/Makefile
> @@ -44,6 +44,7 @@ obj-$(CONFIG_BACKLIGHT_LP855X)		+= lp855x_bl.o
>  obj-$(CONFIG_BACKLIGHT_LP8788)		+= lp8788_bl.o
>  obj-$(CONFIG_BACKLIGHT_LV5207LP)	+= lv5207lp.o
>  obj-$(CONFIG_BACKLIGHT_MAX8925)		+= max8925_bl.o
> +obj-$(CONFIG_BACKLIGHT_MP3309C)		+= mp3309c_bl.o
>  obj-$(CONFIG_BACKLIGHT_MT6370)		+= mt6370-backlight.o
>  obj-$(CONFIG_BACKLIGHT_OMAP1)		+= omap1_bl.o
>  obj-$(CONFIG_BACKLIGHT_PANDORA)		+= pandora_bl.o
> diff --git a/drivers/video/backlight/mp3309c_bl.c b/drivers/video/backlight/mp3309c_bl.c
> new file mode 100644
> index 000000000000..7cb7a542ceca
> --- /dev/null
> +++ b/drivers/video/backlight/mp3309c_bl.c
> @@ -0,0 +1,491 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Driver for MPS MP3309C White LED driver with I2C interface
> + *
> + * Copyright (C) 2023 ASEM Srl
> + * Author: Flavio Suligoi <f.suligoi@xxxxxxx>
> + */
> +
> +#include <linux/backlight.h>
> +#include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/pwm.h>
> +#include <linux/regmap.h>
> +#include <linux/workqueue.h>
> +
> +#define REG_I2C_0	0x00
> +#define REG_I2C_1	0x01
> +
> +#define REG_I2C_0_EN	0x80
> +#define REG_I2C_0_D0	0x40
> +#define REG_I2C_0_D1	0x20
> +#define REG_I2C_0_D2	0x10
> +#define REG_I2C_0_D3	0x08
> +#define REG_I2C_0_D4	0x04
> +#define REG_I2C_0_RSRV1	0x02
> +#define REG_I2C_0_RSRV2	0x01
> +
> +#define REG_I2C_1_RSRV1	0x80
> +#define REG_I2C_1_DIMS	0x40
> +#define REG_I2C_1_SYNC	0x20
> +#define REG_I2C_1_OVP0	0x10
> +#define REG_I2C_1_OVP1	0x08
> +#define REG_I2C_1_VOS	0x04
> +#define REG_I2C_1_LEDO	0x02
> +#define REG_I2C_1_OTP	0x01
> +
> +#define ANALOG_MAX_VAL	31
> +#define ANALOG_REG_MASK 0x7c
> +
> +enum backlight_status {
> +	FIRST_POWER_ON,
> +	BACKLIGHT_OFF,
> +	BACKLIGHT_ON,
> +};
> +
> +enum dimming_mode_value {
> +	DIMMING_PWM,
> +	DIMMING_ANALOG_I2C,
> +};
> +
> +struct mp3309c_platform_data {
> +	u32 max_brightness;
> +	u32 brightness;
> +	u32 switch_on_delay_ms;
> +	u32 switch_off_delay_ms;
> +	u32 reset_on_delay_ms;
> +	u32 reset_on_length_ms;
> +	u8  dimming_mode;
> +	u8  reset_pulse_enable;
> +	u8  over_voltage_protection;
> +
> +	unsigned int status;
> +};
> +
> +struct mp3309c_chip {
> +	struct device *dev;
> +	struct mp3309c_platform_data *pdata;
> +	struct backlight_device *bl;
> +	struct gpio_desc *enable_gpio;
> +	struct regmap *regmap;
> +	struct pwm_device *pwmd;
> +
> +	struct delayed_work enable_work;
> +	struct delayed_work reset_gpio_work;
> +	int irq;
> +
> +	struct gpio_desc *reset_gpio;
> +};
> +
> +static const struct regmap_config mp3309c_regmap = {
> +	.name = "mp3309c_regmap",
> +	.reg_bits = 8,
> +	.reg_stride = 1,
> +	.val_bits = 8,
> +	.max_register = REG_I2C_1,
> +};
> +
> +static int pm3309c_parse_dt_node(struct mp3309c_chip *chip,
> +				 struct mp3309c_platform_data *pdata)

This should be just before probe function. It is part of probe path.

> +{
> +	struct device_node *node = chip->dev->of_node;
> +	const char *tmp_string;
> +	int ret;
> +
> +	if (!node) {
> +		dev_err(chip->dev, "failed to get DT node\n");
> +		return -ENODEV;
> +	}
> +
> +	/*
> +	 * Dimming mode: the MP3309C provides two dimming methods:
> +	 *
> +	 * - PWM mode
> +	 * - Analog by I2C control mode
> +	 */
> +	ret = of_property_read_string(node, "mps,dimming-mode", &tmp_string);
> +	if (ret < 0) {
> +		dev_err(chip->dev, "missed dimming-mode in DT\n");
> +		return ret;
> +	}
> +	if (!strcmp(tmp_string, "pwm")) {
> +		dev_info(chip->dev, "dimming method: PWM\n");

Drop

> +		pdata->dimming_mode = DIMMING_PWM;
> +	}
> +	if (!strcmp(tmp_string, "analog-i2c")) {
> +		dev_info(chip->dev, "dimming method: analog by I2C commands\n");

Drop


> +		pdata->dimming_mode = DIMMING_ANALOG_I2C;
> +	}
> +
> +	/* PWM steps (levels): 0 .. max_brightness */
> +	ret = of_property_read_u32(node, "max-brightness",
> +				   &pdata->max_brightness);
> +	if (ret < 0) {
> +		dev_err(chip->dev, "failed to get max-brightness from DT\n");
> +		return ret;
> +	}
> +
> +	/* Default brightness at startup */
> +	ret = of_property_read_u32(node, "default-brightness",
> +				   &pdata->brightness);
> +	if (ret < 0) {
> +		dev_err(chip->dev,
> +			"failed to get default-brightness from DT\n");
> +		return ret;
> +	}
> +
> +	/*
> +	 * Optional backlight switch-on/off delay
> +	 *
> +	 * Note: set 10ms as minimal value for switch-on delay, to stabilize
> +	 *       video data
> +	 */
> +	pdata->switch_on_delay_ms = 50;
> +	of_property_read_u32(node, "mps,switch-on-delay-ms",
> +			     &pdata->switch_on_delay_ms);
> +	if (pdata->switch_on_delay_ms < 10) {
> +		pdata->switch_on_delay_ms = 10;

You miss constraints in the bindings.

> +		dev_warn(chip->dev,
> +			 "switch-on-delay-ms set to 10ms as minimal value\n");
> +	}
> +	pdata->switch_off_delay_ms = 0;
> +	of_property_read_u32(node, "mps,switch-off-delay-ms",
> +			     &pdata->switch_off_delay_ms);
> +
> +	/*
> +	 * Reset: GPIO, initial delay and pulse length
> +	 *
> +	 * Use this optional GPIO to reset an external device (LCD panel, video
> +	 * FPGA, etc) when the backlight is switched on
> +	 */
> +	pdata->reset_pulse_enable = 0;
> +	chip->reset_gpio = devm_gpiod_get_optional(chip->dev, "mps,reset",
> +						   GPIOD_OUT_LOW);
> +	if (IS_ERR(chip->reset_gpio)) {
> +		ret = PTR_ERR(chip->reset_gpio);
> +		dev_err(chip->dev, "error acquiring reset gpio: %d\n", ret);
> +		return ret;

return dev_err_probe()

> +	}
> +	if (chip->reset_gpio) {
> +		pdata->reset_pulse_enable = 1;
> +
> +		pdata->reset_on_delay_ms = 10;
> +		of_property_read_u32(node, "mps,reset-on-delay-ms",
> +				     &pdata->reset_on_delay_ms);
> +		pdata->reset_on_length_ms = 10;
> +		of_property_read_u32(node, "mps,reset-on-length-ms",
> +				     &pdata->reset_on_length_ms);
> +	}
> +
> +	/*
> +	 * Over-voltage protection (OVP)
> +	 *
> +	 * These (optional) properties are:
> +	 *
> +	 *  - overvoltage-protection-13v --> OVP point set to 13.5V
> +	 *  - overvoltage-protection-24v --> OVP point set to 24V
> +	 *  - overvoltage-protection-35v --> OVP point set to 35.5V
> +	 *
> +	 * If not chosen, the hw default value for OVP is 35.5V
> +	 */
> +	pdata->over_voltage_protection = REG_I2C_1_OVP1;
> +	if (of_property_read_bool(node, "mps,overvoltage-protection-13v"))
> +		pdata->over_voltage_protection = 0x00;
> +	if (of_property_read_bool(node, "mps,overvoltage-protection-24v"))
> +		pdata->over_voltage_protection = REG_I2C_1_OVP0;
> +	if (of_property_read_bool(node, "mps,overvoltage-protection-35v"))
> +		pdata->over_voltage_protection = REG_I2C_1_OVP1;
> +
> +	return 0;
> +}
> +

...

> +
> +static const struct backlight_ops mp3309c_bl_ops = {
> +	.update_status = mp3309c_bl_update_status,
> +};
> +
> +static int mp3309c_probe(struct i2c_client *client)
> +{
> +	struct mp3309c_platform_data *pdata = dev_get_platdata(&client->dev);
> +	struct mp3309c_chip *chip;
> +	struct backlight_properties props;
> +	int ret;
> +
> +	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
> +		dev_err(&client->dev, "failed to check i2c functionality\n");
> +		return -EOPNOTSUPP;
> +	}
> +
> +	chip = devm_kzalloc(&client->dev, sizeof(struct mp3309c_chip),

sizeof(*)

> +			    GFP_KERNEL);
> +	if (!chip)
> +		return -ENOMEM;
> +	chip->dev = &client->dev;
> +
> +	chip->regmap = devm_regmap_init_i2c(client, &mp3309c_regmap);
> +	if (IS_ERR(chip->regmap)) {
> +		ret = PTR_ERR(chip->regmap);
> +		dev_err(&client->dev, "failed to allocate register map\n");

Are you sure regmap allocation should be followed by error message?
Allocations must not... so if this is not allocation, then syntax is:

return dev_err_probe()

> +		return ret;
> +	}
> +
> +	i2c_set_clientdata(client, chip);
> +
> +	if (!pdata) {
> +		pdata = devm_kzalloc(chip->dev,
> +				     sizeof(struct mp3309c_platform_data),

sizeof(*)

> +				     GFP_KERNEL);
> +		if (!pdata)
> +			return -ENOMEM;
> +
> +		ret = pm3309c_parse_dt_node(chip, pdata);
> +		if (ret) {
> +			dev_err(&client->dev, "failed parsing DT node\n");

Why do you print errors multiple times? parse_dt_node already does it.

> +			return ret;
> +		}
> +	}
> +	chip->pdata = pdata;
> +
> +	chip->enable_gpio = devm_gpiod_get_optional(&client->dev, "enable",
> +						    GPIOD_OUT_HIGH);
> +	if (IS_ERR(chip->enable_gpio)) {
> +		ret = PTR_ERR(chip->enable_gpio);
> +		return ret;

return dev_err_probe()

> +	}
> +
> +	/* Backlight */
> +	props.type = BACKLIGHT_RAW;
> +	props.brightness = pdata->brightness;
> +	props.max_brightness = pdata->max_brightness;
> +	props.scale = BACKLIGHT_SCALE_LINEAR;
> +	chip->bl =
> +	    devm_backlight_device_register(chip->dev, "mp3309c_bl",
> +					   chip->dev, chip, &mp3309c_bl_ops,
> +					   &props);
> +	if (IS_ERR(chip->bl)) {
> +		dev_err(&client->dev, "failed registering backlight\n");
> +		return PTR_ERR(chip->bl);

return dev_err_probe()

> +	}
> +	pdata->status = FIRST_POWER_ON;
> +
> +	/* Enable PWM, if required */
> +	if (pdata->dimming_mode == DIMMING_PWM) {
> +		chip->pwmd = devm_pwm_get(chip->dev, NULL);
> +		if (IS_ERR(chip->pwmd)) {
> +			dev_err(&client->dev, "failed getting pwm device\n");
> +			return PTR_ERR(chip->pwmd);

return dev_err_probe()

> +		}
> +		pwm_apply_args(chip->pwmd);
> +	}
> +
> +	/*
> +	 * Workqueue for delayed backlight enabling
> +	 */
> +	INIT_DELAYED_WORK(&chip->enable_work, mp3309c_enable);
> +
> +	/*
> +	 * Workqueue for (optional) external device GPIO reset
> +	 */
> +	if (pdata->reset_pulse_enable) {
> +		dev_info(&client->dev, "reset pulse enabled\n");

Drop, not really helpful.

> +		INIT_DELAYED_WORK(&chip->reset_gpio_work, mp3309c_reset_gpio);
> +	}
> +
> +	dev_info(&client->dev, "MP3309C backlight initialized");

Drop simple tracing messages.

> +	return 0;
> +}
> +
> +static int mp3309c_backlight_switch_off(struct pwm_device *pwmd)
> +{
> +	struct pwm_state pwmstate;
> +
> +	/* Switch-off the backlight */
> +	pwm_get_state(pwmd, &pwmstate);
> +	pwmstate.duty_cycle = 0;
> +	pwmstate.enabled = false;
> +	pwm_apply_state(pwmd, &pwmstate);
> +
> +	return 0;
> +}
> +
> +static void mp3309c_remove(struct i2c_client *client)
> +{
> +	struct mp3309c_chip *chip = i2c_get_clientdata(client);
> +
> +	if (chip->pdata->dimming_mode == DIMMING_PWM)
> +		mp3309c_backlight_switch_off(chip->pwmd);
> +	if (chip->pdata->reset_pulse_enable)
> +		cancel_delayed_work(&chip->reset_gpio_work);
> +}
> +
> +static void mp3309c_shutdown(struct i2c_client *client)
> +{
> +	struct mp3309c_chip *chip = i2c_get_clientdata(client);
> +
> +	if (chip->pdata->dimming_mode == DIMMING_PWM)
> +		mp3309c_backlight_switch_off(chip->pwmd);

Why do you need shutdown function?

> +}
> +
> +static const struct of_device_id mp3309c_match_table[] = {
> +	{ .compatible = "mps,mp3309c-backlight", },
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, mp3309c_match_table);
> +


Best regards,
Krzysztof




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux