Em 13/07/2023 04:51, Pekka Paalanen escreveu:
On Tue, 11 Jul 2023 10:57:57 +0200
Daniel Vetter <daniel@xxxxxxxx> wrote:
On Fri, Jul 07, 2023 at 07:40:59PM -0300, André Almeida wrote:
From: Pekka Paalanen <pekka.paalanen@xxxxxxxxxxxxx>
Specify how the atomic state is maintained between userspace and
kernel, plus the special case for async flips.
Signed-off-by: Pekka Paalanen <pekka.paalanen@xxxxxxxxxxxxx>
Signed-off-by: André Almeida <andrealmeid@xxxxxxxxxx>
---
v4: total rework by Pekka
---
Documentation/gpu/drm-uapi.rst | 41 ++++++++++++++++++++++++++++++++++
1 file changed, 41 insertions(+)
diff --git a/Documentation/gpu/drm-uapi.rst b/Documentation/gpu/drm-uapi.rst
index 65fb3036a580..6a1662c08901 100644
--- a/Documentation/gpu/drm-uapi.rst
+++ b/Documentation/gpu/drm-uapi.rst
@@ -486,3 +486,44 @@ and the CRTC index is its position in this array.
.. kernel-doc:: include/uapi/drm/drm_mode.h
:internal:
+
+KMS atomic state
+================
+
+An atomic commit can change multiple KMS properties in an atomic fashion,
+without ever applying intermediate or partial state changes. Either the whole
+commit succeeds or fails, and it will never be applied partially. This is the
+fundamental improvement of the atomic API over the older non-atomic API which is
+referred to as the "legacy API". Applying intermediate state could unexpectedly
+fail, cause visible glitches, or delay reaching the final state.
+
+An atomic commit can be flagged with DRM_MODE_ATOMIC_TEST_ONLY, which means the
+complete state change is validated but not applied. Userspace should use this
+flag to validate any state change before asking to apply it. If validation fails
+for any reason, userspace should attempt to fall back to another, perhaps
+simpler, final state. This allows userspace to probe for various configurations
+without causing visible glitches on screen and without the need to undo a
+probing change.
+
+The changes recorded in an atomic commit apply on top the current KMS state in
+the kernel. Hence, the complete new KMS state is the complete old KMS state with
+the committed property settings done on top. The kernel will automatically avoid
+no-operation changes, so it is safe and even expected for userspace to send
+redundant property settings. No-operation changes do not count towards actually
+needed changes, e.g. setting MODE_ID to a different blob with identical
+contents as the current KMS state shall not be a modeset on its own.
Small clarification: The kernel indeed tries very hard to make redundant
changes a no-op, and I think we should consider any issues here bugs. But
it still has to check, which means it needs to acquire the right locks and
put in the right (cross-crtc) synchronization points, and due to
implmentation challenges it's very hard to try to avoid that in all cases.
So adding redundant changes especially across crtc (and their connected
planes/connectors) might result in some oversynchronization issues, and
userspace should therefore avoid them if feasible.
With some sentences added to clarify this:
Reviewed-by: Daniel Vetter <daniel.vetter@xxxxxxxx>
After talking on IRC yesterday, we realized that the no-op rule is
nowhere near as generic as I have believed. Roughly:
https://oftc.irclog.whitequark.org/dri-devel/2023-07-12#1689152446-1689157291;
How about:
The changes recorded in an atomic commit apply on top the current KMS
state in the kernel. Hence, the complete new KMS state is the complete
old KMS state with the committed property settings done on top. The
kernel will try to avoid no-operation changes, so it is safe for
userspace to send redundant property settings. However, the kernel can
not assure that every redundant information will always result in a
no-op, giving the need to take locks to check par of the state. Giving
that, some redundant information can lead to a full damage path. This is
not something bad by itself, but userspace need to be aware of that side
effect.
Thanks,
pq
+
+A "modeset" is a change in KMS state that might enable, disable, or temporarily
+disrupt the emitted video signal, possibly causing visible glitches on screen. A
+modeset may also take considerably more time to complete than other kinds of
+changes, and the video sink might also need time to adapt to the new signal
+properties. Therefore a modeset must be explicitly allowed with the flag
+DRM_MODE_ATOMIC_ALLOW_MODESET. This in combination with
+DRM_MODE_ATOMIC_TEST_ONLY allows userspace to determine if a state change is
+likely to cause visible disruption on screen and avoid such changes when end
+users do not expect them.
+
+An atomic commit with the flag DRM_MODE_PAGE_FLIP_ASYNC is allowed to
+effectively change only the FB_ID property on any planes. No-operation changes
+are ignored as always. Changing any other property will cause the commit to be
+rejected.
--
2.41.0
