On Thu, 29 Jun 2023 at 15:14, Marijn Suijten
<marijn.suijten@xxxxxxxxxxxxxx> wrote:
>
> On 2023-06-29 13:56:25, Dmitry Baryshkov wrote:
> > On 27/06/2023 23:14, Marijn Suijten wrote:
> > > Enable and configure the dispcc node on SM6125 for consumption by MDSS
> > > later on.
> > >
> > > Signed-off-by: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx>
> > > ---
> > > arch/arm64/boot/dts/qcom/sm6125.dtsi | 25 +++++++++++++++++++++++++
> > > 1 file changed, 25 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/sm6125.dtsi b/arch/arm64/boot/dts/qcom/sm6125.dtsi
> > > index edb03508dba3..a5cc0d43d2d9 100644
> > > --- a/arch/arm64/boot/dts/qcom/sm6125.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/sm6125.dtsi
> > > @@ -3,6 +3,7 @@
> > > * Copyright (c) 2021, Martin Botka <martin.botka@xxxxxxxxxxxxxx>
> > > */
> > >
> > > +#include <dt-bindings/clock/qcom,dispcc-sm6125.h>
> > > #include <dt-bindings/clock/qcom,gcc-sm6125.h>
> > > #include <dt-bindings/clock/qcom,rpmcc.h>
> > > #include <dt-bindings/dma/qcom-gpi.h>
> > > @@ -1203,6 +1204,30 @@ sram@4690000 {
> > > reg = <0x04690000 0x10000>;
> > > };
> > >
> > > + dispcc: clock-controller@5f00000 {
> > > + compatible = "qcom,sm6125-dispcc";
> > > + reg = <0x05f00000 0x20000>;
> > > + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
> > > + <0>,
> > > + <0>,
> > > + <0>,
> > > + <0>,
> > > + <0>,
> > > + <&gcc GCC_DISP_AHB_CLK>,
> > > + <&gcc GCC_DISP_GPLL0_DIV_CLK_SRC>;
> > > + clock-names = "bi_tcxo",
> > > + "dsi0_phy_pll_out_byteclk",
> > > + "dsi0_phy_pll_out_dsiclk",
> > > + "dsi1_phy_pll_out_dsiclk",
> > > + "dp_phy_pll_link_clk",
> > > + "dp_phy_pll_vco_div_clk",
> > > + "cfg_ahb_clk",
> > > + "gcc_disp_gpll0_div_clk_src";
> > > + power-domains = <&rpmpd SM6125_VDDCX>;
> >
> > Would it be logical to specify the required-opps too?
>
> Perhaps, but barely any other SoC aside from sm8x50 sets it on dispcc.
> What should it be, rpmhpd_opp_low_svs? IIRC we used "svs" for the DSI
> PHY despite not having a reference value downstream (it sets a range of
> NOM-TURBO_NO_CPR, and RETENTION when it's off).
Then for DSI PHY the required-opps should be rpmpd_opp_nom.
For the dispcc I think the rpmpd_opp_ret, the lowest possible vote,
should be enough.
>
> - Marijn
>
> >
> > > + #clock-cells = <1>;
> > > + #power-domain-cells = <1>;
> > > + };
> > > +
> > > apps_smmu: iommu@c600000 {
> > > compatible = "qcom,sm6125-smmu-500", "qcom,smmu-500", "arm,mmu-500";
> > > reg = <0x0c600000 0x80000>;
> > >
> >
> > --
> > With best wishes
> > Dmitry
> >
--
With best wishes
Dmitry
