On 24.06.2023 02:41, Marijn Suijten wrote: > Enable MDSS and DSI, and configure the Samsung SOFEF01-M ams597ut01 > 6.0" 1080x2520 panel. > > Signed-off-by: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx> > --- > .../dts/qcom/sm6125-sony-xperia-seine-pdx201.dts | 59 ++++++++++++++++++++++ > 1 file changed, 59 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts b/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts > index 9f8a9ef398a2..bdf7c15f9b83 100644 > --- a/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts > +++ b/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts > @@ -179,6 +179,43 @@ &i2c3 { > /* Cirrus Logic CS35L41 boosted audio amplifier @ 40 */ > }; > > +&mdss { > + status = "okay"; > +}; > + > +&mdss_dsi0 { > + vdda-supply = <&pm6125_l18>; > + status = "okay"; > + > + panel@0 { > + compatible = "samsung,sofef01-m-ams597ut01"; > + reg = <0>; > + > + reset-gpios = <&tlmm 90 GPIO_ACTIVE_LOW>; > + > + vddio-supply = <&pm6125_l12>; > + > + pinctrl-0 = <&sde_dsi_active &sde_te_active_sleep>; > + pinctrl-1 = <&sde_dsi_sleep &sde_te_active_sleep>; > + pinctrl-names = "default", "sleep"; > + > + port { > + panel_in: endpoint { > + remote-endpoint = <&mdss_dsi0_out>; > + }; > + }; > + }; > +}; > + > +&mdss_dsi0_out { > + remote-endpoint = <&panel_in>; > + data-lanes = <0 1 2 3>; > +}; > + > +&mdss_dsi0_phy { > + status = "okay"; > +}; > + > &pm6125_adc { > pinctrl-names = "default"; > pinctrl-0 = <&camera_flash_therm &emmc_ufs_therm &rf_pa1_therm>; > @@ -469,6 +506,28 @@ vol_down_n: vol-down-n-state { > drive-strength = <2>; > bias-disable; > }; > + > + sde_te_active_sleep: sde-te-active-sleep-state { > + pins = "gpio89"; > + function = "mdp_vsync"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + sde_dsi_active: sde-dsi-active-state { > + pins = "gpio90"; > + function = "gpio"; > + drive-strength = <8>; > + bias-disable; > + }; > + > + sde_dsi_sleep: sde-dsi-sleep-state { > + pins = "gpio90"; > + function = "gpio"; > + drive-strength = <2>; > + bias-pull-down; > + }; s/sde/mdss as per Dmitry's recent request Konrad > + > }; > > &usb3 { >