Hi Biju,
On Tue, Jun 13, 2023 at 6:11 PM Biju Das <biju.das.jz@xxxxxxxxxxxxxx> wrote:
> > Subject: Re: [PATCH v5 01/11] i2c: Enhance i2c_new_ancillary_device API
> > On Tue, Jun 13, 2023 at 12:45 PM Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
> > wrote:
> > > > Subject: Re: [PATCH v5 01/11] i2c: Enhance i2c_new_ancillary_device
> > > > API On Mon, Jun 12, 2023 at 10:43 PM Wolfram Sang <wsa@xxxxxxxxxx>
> > wrote:
> > > > > > Perhaps we should first think through what an ancillary device
> > > > > > really is. My understanding is that it is used to talk to
> > > > > > secondary addresses of a multi-address I2C slave device.
> > > > >
> > > > > As I mentioned somewhere before, this is not the case. Ancillary
> > > > > devices are when one *driver* handles more than one address.
> > > > > Everything else has been handled differently in the past (for all
> > > > > the
> > > > uses I am aware of).
> > > > >
> > > > > Yet, I have another idea which is so simple that I wonder if it
> > > > > maybe has already been discussed so far?
> > > > >
> > > > > * have two regs in the bindings
> > > > > * use the second reg with i2c_new_client_device to instantiate the
> > > > > RTC sibling. 'struct i2c_board_info', which is one parameter,
> > should
> > > > > have enough options to pass data, e.g it has a software_node.
> > > > >
> > > > > Should work or did I miss something here?
> > > >
> > > > That should work, mostly (i2c_new_dummy_device() also calls
> > > > i2c_new_client_device()). And as i2c_board_info has an of_node
> > > > member (something I had missed before!), the new I2C device can
> > > > access the clocks in the DT node using the standard way.
> > >
> > > Looks like, I cannot assign of_node member like below as it results in
> > > pinctrl failure[1] during device bind.
> > >
> > > info.of_node = client->dev.of_node;
> > >
> > > [1]
> > > pinctrl-rzg2l 11030000.pinctrl: pin P43_0 already requested by 3-0012;
> > > cannot claim for 3-006f pinctrl-rzg2l 11030000.pinctrl: pin-344
> > > (3-006f) status -22 pinctrl-rzg2l 11030000.pinctrl: could not request
> > > pin 344 (P43_0) from group pmic on device pinctrl-rzg2l
> > > raa215300 3-006f: Error applying setting, reverse things back
> >
> > Where do you have a reference to pin P43_0 in your DT?
>
> The reference to pin P43_0 is added in the PMIC node.
>
> I have done modification on my board to test PMIC INT# on RZ/G2L SMARC EVK
> by wiring R83 on SoM module and PMOD0 PIN7.
>
> > The last versions you posted did not have any pinctrl properties?
>
> By default, PMIC_INT# is not populated RZ/G2L SMARC EVK, so I haven't added
> Support for PMIC_INT# for the patches posted till date.
>
> Yesterday I checked with HW people, is there a way to enable PMIC_INT#
> and they told me to do the above HW modification.
>
> Today I found this issue, with this modified HW and PMIC INT# enabled on the DT,
> while assigning of_node of PMIC with info.of_node. It is just a coincidence.
IC.
So you now have two Linux devices pointing to the same DT node,
causing pinctrl issues...
I know this won't solve the core issue, but what is the exact pintrl
configuration you are using? Is this using a GPIO with interrupt
capabilities, or a dedicated interrupt pin? In case of the former,
you don't need a pinctrl property in DT, as the GPIO controller itself
should take care of that by asking the pin controller to configure
the pin properly through pinctrl_gpio_request().
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
