Re: [RESEND PATCH v3] mtd: rawnand: macronix: OTP access for MX30LFxG18AC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 22.05.2023 17:14, Miquel Raynal wrote:
> Hi Arseniy,
> 
> avkrasnov@xxxxxxxxxxxxxx wrote on Mon, 15 May 2023 12:49:50 +0300:
> 
>> Hello @Miquel!
>>
>> Sorry, but who could review this patch? :) IIUC this logic is very hw specific and we need
>> someone who knows it well? I tested this patch on our devices (with already known Meson NAND
>> controller).
> 
> + Jaime, who might test
> 
>>
>> Thanks, Arseniy
>>
>> On 11.05.2023 21:21, Arseniy Krasnov wrote:
>>> Cc: Mason Yang <masonccyang@xxxxxxxxxxx> and Boris Brezillon <boris.brezillon@xxxxxxxxxxxxx>
>>>
>>> On 11.05.2023 18:21, Arseniy Krasnov wrote:  
>>>> This adds support for OTP area access on MX30LFxG18AC chip series.
>>>>
>>>> Changelog:
>>>>   v1 -> v2:
>>>>   * Add slab.h include due to kernel test robot error.
>>>>   v2 -> v3:
>>>>   * Use 'uint64_t' as input argument for 'do_div()' instead
>>>>     of 'unsigned long' due to kernel test robot error.
>>>>
>>>> Signed-off-by: Arseniy Krasnov <AVKrasnov@xxxxxxxxxxxxxx>
>>>> ---
>>>>  drivers/mtd/nand/raw/nand_macronix.c | 213 +++++++++++++++++++++++++++
>>>>  1 file changed, 213 insertions(+)
>>>>
>>>> diff --git a/drivers/mtd/nand/raw/nand_macronix.c b/drivers/mtd/nand/raw/nand_macronix.c
>>>> index 1472f925f386..2301f990678e 100644
>>>> --- a/drivers/mtd/nand/raw/nand_macronix.c
>>>> +++ b/drivers/mtd/nand/raw/nand_macronix.c
>>>> @@ -6,6 +6,7 @@
>>>>   * Author: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>
>>>>   */
>>>>  
>>>> +#include <linux/slab.h>
>>>>  #include "linux/delay.h"
>>>>  #include "internals.h"
>>>>  
>>>> @@ -31,6 +32,20 @@
>>>>  
>>>>  #define MXIC_CMD_POWER_DOWN 0xB9
>>>>  
>>>> +#define ONFI_FEATURE_ADDR_30LFXG18AC_OTP	0x90
>>>> +#define MACRONIX_30LFXG18AC_OTP_START_PAGE	0
>>>> +#define MACRONIX_30LFXG18AC_OTP_PAGES		30
>>>> +#define MACRONIX_30LFXG18AC_OTP_PAGE_SIZE	2112
>>>> +#define MACRONIX_30LFXG18AC_OTP_START_BYTE	\
>>>> +	(MACRONIX_30LFXG18AC_OTP_START_PAGE *	\
>>>> +	 MACRONIX_30LFXG18AC_OTP_PAGE_SIZE)
>>>> +#define MACRONIX_30LFXG18AC_OTP_SIZE_BYTES	\
>>>> +	(MACRONIX_30LFXG18AC_OTP_PAGES *	\
>>>> +	 MACRONIX_30LFXG18AC_OTP_PAGE_SIZE)
>>>> +
>>>> +#define MACRONIX_30LFXG18AC_OTP_EN		BIT(0)
>>>> +#define MACRONIX_30LFXG18AC_OTP_LOCKED		BIT(1)
>>>> +
>>>>  struct nand_onfi_vendor_macronix {
>>>>  	u8 reserved;
>>>>  	u8 reliability_func;
>>>> @@ -316,6 +331,203 @@ static void macronix_nand_deep_power_down_support(struct nand_chip *chip)
>>>>  	chip->ops.resume = mxic_nand_resume;
>>>>  }
>>>>  
>>>> +static int macronix_30lfxg18ac_get_otp_info(struct mtd_info *mtd, size_t len,
>>>> +					    size_t *retlen,
>>>> +					    struct otp_info *buf)
>>>> +{
>>>> +	if (len < sizeof(*buf))
>>>> +		return -EINVAL;
>>>> +
>>>> +	/* Don't know how to check that OTP is locked. */
> 
> Jaime, any idea?
> 

That will be great, because i didn't found any doc about that

Thanks

>>>> +	buf->locked = 0;
>>>> +	buf->start = MACRONIX_30LFXG18AC_OTP_START_BYTE;
>>>> +	buf->length = MACRONIX_30LFXG18AC_OTP_SIZE_BYTES;
>>>> +
>>>> +	*retlen = sizeof(*buf);
>>>> +
>>>> +	return 0;
>>>> +}
>>>> +
>>>> +static int macronix_30lfxg18ac_otp_enable(struct nand_chip *nand)
>>>> +{
>>>> +	uint8_t feature_buf[ONFI_SUBFEATURE_PARAM_LEN] = { 0 };
>>>> +
>>>> +	feature_buf[0] = MACRONIX_30LFXG18AC_OTP_EN;
>>>> +	return nand_set_features(nand, ONFI_FEATURE_ADDR_30LFXG18AC_OTP,
>>>> +				 feature_buf);
>>>> +}
>>>> +
>>>> +static int macronix_30lfxg18ac_otp_disable(struct nand_chip *nand)
>>>> +{
>>>> +	uint8_t feature_buf[ONFI_SUBFEATURE_PARAM_LEN] = { 0 };
>>>> +
>>>> +	return nand_set_features(nand, ONFI_FEATURE_ADDR_30LFXG18AC_OTP,
>>>> +				 feature_buf);
>>>> +}
>>>> +
>>>> +static int __macronix_30lfxg18ac_rw_otp(struct mtd_info *mtd,
>>>> +					loff_t offs_in_flash,
>>>> +					size_t len, size_t *retlen,
>>>> +					u_char *buf, bool write)
>>>> +{
>>>> +	struct nand_chip *nand;
>>>> +	size_t bytes_handled;
>>>> +	off_t offs_in_page;
>>>> +	uint64_t page;
>>>> +	void *dma_buf;
>>>> +	int ret;
>>>> +
>>>> +	/* 'nand_prog/read_page_op()' may use 'buf' as DMA buffer,
>>>> +	 * so allocate properly aligned memory for it. This is
>>>> +	 * needed because cross page accesses may lead to unaligned
>>>> +	 * buffer address for DMA.
>>>> +	 */
>>>> +	dma_buf = kmalloc(MACRONIX_30LFXG18AC_OTP_PAGE_SIZE, GFP_KERNEL);
>>>> +	if (!dma_buf)
>>>> +		return -ENOMEM;
>>>> +
>>>> +	nand = mtd_to_nand(mtd);
>>>> +	nand_select_target(nand, 0);
>>>> +
>>>> +	ret = macronix_30lfxg18ac_otp_enable(nand);
>>>> +	if (ret)
>>>> +		goto out_otp;
>>>> +
>>>> +	page = offs_in_flash;
>>>> +	/* 'page' will be result of division. */
>>>> +	offs_in_page = do_div(page, MACRONIX_30LFXG18AC_OTP_PAGE_SIZE);
>>>> +	bytes_handled = 0;
>>>> +
>>>> +	while (bytes_handled < len &&
>>>> +	       page < MACRONIX_30LFXG18AC_OTP_PAGES) {
>>>> +		size_t bytes_to_handle;
>>>> +
>>>> +		bytes_to_handle = min_t(size_t, len - bytes_handled,
>>>> +					MACRONIX_30LFXG18AC_OTP_PAGE_SIZE -
>>>> +					offs_in_page);
>>>> +
>>>> +		if (write) {
>>>> +			memcpy(dma_buf, &buf[bytes_handled], bytes_to_handle);
>>>> +			ret = nand_prog_page_op(nand, page, offs_in_page,
>>>> +						dma_buf, bytes_to_handle);
>>>> +		} else {
>>>> +			ret = nand_read_page_op(nand, page, offs_in_page,
>>>> +						dma_buf, bytes_to_handle);
>>>> +			if (!ret)
>>>> +				memcpy(&buf[bytes_handled], dma_buf,
>>>> +				       bytes_to_handle);
>>>> +		}
>>>> +		if (ret)
>>>> +			goto out_otp;
>>>> +
>>>> +		bytes_handled += bytes_to_handle;
>>>> +		offs_in_page = 0;
>>>> +		page++;
>>>> +	}
>>>> +
>>>> +	*retlen = bytes_handled;
>>>> +
>>>> +out_otp:
>>>> +	if (ret)
>>>> +		dev_err(&mtd->dev, "failed to perform OTP IO: %i\n", ret);
>>>> +
>>>> +	ret = macronix_30lfxg18ac_otp_disable(nand);
>>>> +	WARN(ret, "failed to leave OTP mode after %s\n",
>>>> +	     write ? "write" : "read");
> 
> Let's avoid WARN() calls (none in this driver are relevant IMHO). Just a
> dev_err() should be enough.

Done in v4

> 
>>>> +	nand_deselect_target(nand);
>>>> +	kfree(dma_buf);
>>>> +
>>>> +	return ret;
>>>> +}
>>>> +
>>>> +static int macronix_30lfxg18ac_write_otp(struct mtd_info *mtd, loff_t to,
>>>> +					 size_t len, size_t *rlen,
>>>> +					 const u_char *buf)
>>>> +{
>>>> +	return __macronix_30lfxg18ac_rw_otp(mtd, to, len, rlen, (u_char *)buf,
>>>> +					    true);
>>>> +}
>>>> +
>>>> +static int macronix_30lfxg18ac_read_otp(struct mtd_info *mtd, loff_t from,
>>>> +					size_t len, size_t *rlen,
>>>> +					u_char *buf)
>>>> +{
>>>> +	return __macronix_30lfxg18ac_rw_otp(mtd, from, len, rlen, buf, false);
>>>> +}
>>>> +
>>>> +static int macronix_30lfxg18ac_lock_otp(struct mtd_info *mtd, loff_t from,
>>>> +					size_t len)
>>>> +{
>>>> +	uint8_t feature_buf[ONFI_SUBFEATURE_PARAM_LEN] = { 0 };
>>>> +	struct nand_chip *nand;
>>>> +	int ret;
>>>> +
>>>> +	if (from != MACRONIX_30LFXG18AC_OTP_START_BYTE ||
>>>> +	    len != MACRONIX_30LFXG18AC_OTP_SIZE_BYTES)
>>>> +		return -EINVAL;
>>>> +
>>>> +	dev_dbg(&mtd->dev, "locking OTP\n");
>>>> +
>>>> +	nand = mtd_to_nand(mtd);
>>>> +	nand_select_target(nand, 0);
>>>> +
>>>> +	feature_buf[0] = MACRONIX_30LFXG18AC_OTP_EN |
>>>> +			 MACRONIX_30LFXG18AC_OTP_LOCKED;
>>>> +	ret = nand_set_features(nand, ONFI_FEATURE_ADDR_30LFXG18AC_OTP,
>>>> +				feature_buf);
>>>> +	if (ret) {
>>>> +		dev_err(&mtd->dev,
>>>> +			"failed to lock OTP (set features): %i\n", ret);
>>>> +		nand_deselect_target(nand);
>>>> +		return ret;
>>>> +	}
>>>> +
>>>> +	/* Do dummy page prog with zero address. */
>>>> +	feature_buf[0] = 0;
>>>> +	ret = nand_prog_page_op(nand, 0, 0, feature_buf, 1);
>>>> +	if (ret)
>>>> +		dev_err(&mtd->dev,
>>>> +			"failed to lock OTP (page prog): %i\n", ret);
>>>> +
>>>> +	ret = macronix_30lfxg18ac_otp_disable(nand);
>>>> +	WARN(ret, "failed to leave OTP mode after lock\n");
>>>> +
>>>> +	nand_deselect_target(nand);
>>>> +
>>>> +	return ret;
>>>> +}
>>>> +
>>>> +static void macronix_nand_setup_otp(struct nand_chip *chip)
>>>> +{
>>>> +	static const char * const supported_otp_models[] = {
>>>> +		"MX30LF1G18AC",
>>>> +		"MX30LF2G18AC",
>>>> +		"MX30LF4G18AC",
>>>> +	};
>>>> +	struct mtd_info *mtd;
>>>> +
>>>> +	if (!chip->parameters.supports_set_get_features)
>>>> +		return;
>>>> +
>>>> +	if (match_string(supported_otp_models,
>>>> +			 ARRAY_SIZE(supported_otp_models),
>>>> +			 chip->parameters.model) < 0)
>>>> +		return;
> 
> I would start by checking the model, then it's list of supported ops.
> 

Done in v4

>>>> +
>>>> +	bitmap_set(chip->parameters.get_feature_list,
>>>> +		   ONFI_FEATURE_ADDR_30LFXG18AC_OTP, 1);
>>>> +	bitmap_set(chip->parameters.set_feature_list,
>>>> +		   ONFI_FEATURE_ADDR_30LFXG18AC_OTP, 1);
>>>> +
>>>> +	mtd = nand_to_mtd(chip);
>>>> +	mtd->_get_fact_prot_info = macronix_30lfxg18ac_get_otp_info;
>>>> +	mtd->_read_fact_prot_reg = macronix_30lfxg18ac_read_otp;
>>>> +	mtd->_get_user_prot_info = macronix_30lfxg18ac_get_otp_info;
>>>> +	mtd->_read_user_prot_reg = macronix_30lfxg18ac_read_otp;
>>>> +	mtd->_write_user_prot_reg = macronix_30lfxg18ac_write_otp;
>>>> +	mtd->_lock_user_prot_reg = macronix_30lfxg18ac_lock_otp;
>>>> +}
>>>> +
>>>>  static int macronix_nand_init(struct nand_chip *chip)
>>>>  {
>>>>  	if (nand_is_slc(chip))
>>>> @@ -325,6 +537,7 @@ static int macronix_nand_init(struct nand_chip *chip)
>>>>  	macronix_nand_onfi_init(chip);
>>>>  	macronix_nand_block_protection_support(chip);
>>>>  	macronix_nand_deep_power_down_support(chip);
>>>> +	macronix_nand_setup_otp(chip);
>>>>  
>>>>  	return 0;
>>>>  }  
> 
> 
> Thanks,
> Miquèl

Thanks, Arseniy



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux