On 5/18/2023 3:37 PM, Dmitry Baryshkov wrote:
On Fri, 19 May 2023 at 01:17, Jessica Zhang <quic_jesszhan@xxxxxxxxxxx> wrote:On 5/17/2023 5:19 PM, Dmitry Baryshkov wrote:On 16/05/2023 23:20, Jessica Zhang wrote:Add support for the 1080x2340 Visionox R66451 AMOLED DSI panel that comes with the Qualcomm HDK8350 display expansion pack. The panel enables display compression (DSC v1.2) by default. Signed-off-by: Jessica Zhang <quic_jesszhan@xxxxxxxxxxx> --- drivers/gpu/drm/panel/Kconfig | 8 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-visionox-r66451.c | 395 ++++++++++++++++++++++++++ 3 files changed, 404 insertions(+) diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 29cf5fa39ff2..9c2c36dbddf3 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -766,6 +766,14 @@ config DRM_PANEL_VISIONOX_VTDR6130 Say Y here if you want to enable support for Visionox VTDR6130 1080x2400 AMOLED DSI panel. +config DRM_PANEL_VISIONOX_R66451 + tristate "Visionox R66451" + depends on OF + depends on DRM_MIPI_DSI + help + Say Y here if you want to enable support for Visionox + R66451 1080x2340 AMOLED DSI panel. + config DRM_PANEL_WIDECHIPS_WS2401 tristate "Widechips WS2401 DPI panel driver" depends on SPI && GPIOLIB diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index b3e8ba29edd3..e043a92ee676 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -78,5 +78,6 @@ obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o obj-$(CONFIG_DRM_PANEL_VISIONOX_RM69299) += panel-visionox-rm69299.o obj-$(CONFIG_DRM_PANEL_VISIONOX_VTDR6130) += panel-visionox-vtdr6130.o +obj-$(CONFIG_DRM_PANEL_VISIONOX_R66451) += panel-visionox-r66451.o obj-$(CONFIG_DRM_PANEL_WIDECHIPS_WS2401) += panel-widechips-ws2401.o obj-$(CONFIG_DRM_PANEL_XINPENG_XPP055C272) += panel-xinpeng-xpp055c272.o diff --git a/drivers/gpu/drm/panel/panel-visionox-r66451.c b/drivers/gpu/drm/panel/panel-visionox-r66451.c new file mode 100644 index 000000000000..e3648ead3e84 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-visionox-r66451.c @@ -0,0 +1,395 @@ +//SPDX-License-Identifier: GPL-2.0-only +//Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved. + +#include <linux/backlight.h> +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/regulator/consumer.h> + +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> +#include <drm/display/drm_dsc.h> +#include <drm/display/drm_dsc_helper.h> + +#include <video/mipi_display.h> + +struct visionox_r66451 { + struct drm_panel panel; + struct mipi_dsi_device *dsi; + struct gpio_desc *reset_gpio; + struct regulator_bulk_data supplies[2]; + bool prepared, enabled; +}; + +static inline struct visionox_r66451 *to_visionox_r66451(struct drm_panel *panel) +{ + return container_of(panel, struct visionox_r66451, panel); +} + +static void visionox_r66451_reset(struct visionox_r66451 *ctx) +{ + gpiod_set_value_cansleep(ctx->reset_gpio, 0); + usleep_range(10000, 10100); + gpiod_set_value_cansleep(ctx->reset_gpio, 1); + usleep_range(10000, 10100); + gpiod_set_value_cansleep(ctx->reset_gpio, 0); + usleep_range(10000, 10100); +} + +static int visionox_r66451_on(struct visionox_r66451 *ctx) +{ + struct mipi_dsi_device *dsi = ctx->dsi; + struct device *dev = &dsi->dev; + int ret; + + dsi->mode_flags |= MIPI_DSI_MODE_LPM; + + mipi_dsi_dcs_write_seq(dsi, 0xb0, 0x00); + mipi_dsi_dcs_write_seq(dsi, 0xc2, + 0x09, 0x24, 0x0c, 0x00, 0x00, 0x0c, 0x00, 0x00, 0x00, + 0x09, 0x3c); + mipi_dsi_dcs_write_seq(dsi, 0xd7, + 0x00, 0xb9, 0x3c, 0x00, 0x40, 0x04, 0x00, 0xa0, 0x0a, + 0x00, 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x19, + 0x3c, 0x00, 0x40, 0x04, 0x00, 0xa0, 0x0a); + mipi_dsi_dcs_write_seq(dsi, 0xb0, 0x80); + mipi_dsi_dcs_write_seq(dsi, 0xde, + 0x40, 0x00, 0x18, 0x00, 0x18, 0x00, 0x18, 0x00, 0x18, + 0x10, 0x00, 0x18, 0x00, 0x18, 0x00, 0x18, 0x02, 0x00, 0x00); + mipi_dsi_dcs_write_seq(dsi, 0xb0, 0x04); + mipi_dsi_dcs_write_seq(dsi, 0xe8, 0x00, 0x02); + mipi_dsi_dcs_write_seq(dsi, 0xe4, 0x00, 0x08); + mipi_dsi_dcs_write_seq(dsi, 0xb0, 0x00); + mipi_dsi_dcs_write_seq(dsi, 0xc4, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x32); + mipi_dsi_dcs_write_seq(dsi, 0xcf, + 0x64, 0x0b, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x08, + 0x00, 0x0b, 0x77, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, + 0x02, 0x02, 0x02, 0x02, 0x02, 0x03); + mipi_dsi_dcs_write_seq(dsi, 0xd3, + 0x45, 0x00, 0x00, 0x01, 0x13, 0x15, 0x00, 0x15, 0x07, + 0x0f, 0x77, 0x77, 0x77, 0x37, 0xb2, 0x11, 0x00, 0xa0, + 0x3c, 0x9c); + mipi_dsi_dcs_write_seq(dsi, 0xd7, + 0x00, 0xb9, 0x34, 0x00, 0x40, 0x04, 0x00, 0xa0, 0x0a, + 0x00, 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x19, + 0x34, 0x00, 0x40, 0x04, 0x00, 0xa0, 0x0a); + mipi_dsi_dcs_write_seq(dsi, 0xd8, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x3a, 0x00, 0x3a, 0x00, 0x3a, 0x00, 0x3a, 0x00, 0x3a, + 0x05, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x0a, 0x00, 0x0a, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0a, + 0x00, 0x32, 0x00, 0x0a, 0x00, 0x22); + mipi_dsi_dcs_write_seq(dsi, 0xdf, + 0x50, 0x42, 0x58, 0x81, 0x2d, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x6b, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x01, 0x0f, 0xff, 0xd4, 0x0e, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x0f, 0x53, 0xf1, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00); + mipi_dsi_dcs_write_seq(dsi, 0xf7, 0x01); + mipi_dsi_dcs_write_seq(dsi, 0xb0, 0x80); + mipi_dsi_dcs_write_seq(dsi, 0xe4, 0x34, 0xb4, 0x00, 0x00, 0x00, 0x39, 0x04, 0x09, 0x34); + mipi_dsi_dcs_write_seq(dsi, 0xe6, 0x00); + mipi_dsi_dcs_write_seq(dsi, 0xb0, 0x04); + mipi_dsi_dcs_write_seq(dsi, 0xdf, 0x50, 0x40); + mipi_dsi_dcs_write_seq(dsi, 0xf3, 0x50, 0x00, 0x00, 0x00, 0x00); + mipi_dsi_dcs_write_seq(dsi, 0xf2, 0x11); + mipi_dsi_dcs_write_seq(dsi, 0xf3, 0x01, 0x00, 0x00, 0x00, 0x01); + mipi_dsi_dcs_write_seq(dsi, 0xf4, 0x00, 0x02); + mipi_dsi_dcs_write_seq(dsi, 0xf2, 0x19); + mipi_dsi_dcs_write_seq(dsi, 0xdf, 0x50, 0x42); + mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK); + mipi_dsi_dcs_write_seq(dsi, MIPI_DCS_SET_COLUMN_ADDRESS, 0x00, 0x00, 0x04, 0x37);Please use mipi_dsi_dcs_set_column_address(dsi, 0, 1080 - 1);Hi Dmitry, Acked.+ mipi_dsi_dcs_write_seq(dsi, MIPI_DCS_SET_PAGE_ADDRESS, 0x00, 0x00, 0x09, 0x23);mipi_dsi_dcs_set_page_address(dsi, 0, 2340 - 1);Acked.+ + ret = mipi_dsi_dcs_exit_sleep_mode(dsi); + if (ret < 0) { + dev_err(dev, "Failed to exit sleep mode: %d\n", ret); + return ret; + } + msleep(120); + + ret = mipi_dsi_dcs_set_display_on(dsi);Should the mipi_dsi_dcs_set_display_on() (and maybe exit sleep mode) be a a part of _enable()? Correspondingly _off should IMO be a part of _disable callback().Acked. Looking at the downstream code, it seems that all the dcs on commands can be sent within _enable() (and similarly for the off commands with _disable()).I wouldn't check against the downstream. The distinction is that prepare() is called before enabling the video stream and as such it usually contains commands to set up the panel parameters. The enable() callback is called after starting the video stream, so it should just turn on the image output, the backlight, etc..
Hi Dmitry, Got it.
+ if (ret < 0) { + dev_err(dev, "Failed on set display on: %d\n", ret); + return ret; + } + msleep(20);Do we need to add here the following line? dsi->mode_flags &= ~MIPI_DSI_MODE_LPM;Do you mean within the return on error block?Within the return. I think this might depend on the panel itself, see how other panels handle toggling MIPI_DSI_MODE_LPM. E.g. panel-dsi-cm or panel-novatek-nt35950 unsets MIPI_DSI_MODE_LPM at the end of power_on. Some of the panels also toggle LPM while reading or updating the backlight.
Understood. FWIW, I'm seeing that there are others like panel-visionox-vtdr6130.c that don't unset MODE_LPM after sending the DCS commands.
I'll double check what we should be doing for r66451. Thanks, Jessica Zhang
From my understanding, we should be setting the MIPI_DSI_MODE_LPM for panel_on() then unsetting MODE_LPM in panel_off().+ + return 0; +} + +static int visionox_r66451_off(struct visionox_r66451 *ctx) +{ + struct mipi_dsi_device *dsi = ctx->dsi; + struct device *dev = &dsi->dev; + int ret; + + dsi->mode_flags &= ~MIPI_DSI_MODE_LPM; + + ret = mipi_dsi_dcs_set_display_off(dsi); + if (ret < 0) { + dev_err(dev, "Failed to set display off: %d\n", ret); + return ret; + } + msleep(20); + + ret = mipi_dsi_dcs_enter_sleep_mode(dsi); + if (ret < 0) { + dev_err(dev, "Failed to enter sleep mode: %d\n", ret); + return ret; + } + msleep(120); + + return 0; +} + +static int visionox_r66451_prepare(struct drm_panel *panel) +{ + struct visionox_r66451 *ctx = to_visionox_r66451(panel); + struct device *dev = &ctx->dsi->dev; + int ret; + + if (ctx->prepared) + return 0; + + ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), + ctx->supplies); + if (ret < 0) + return ret; + + visionox_r66451_reset(ctx); + + ret = visionox_r66451_on(ctx); + if (ret < 0) { + dev_err(dev, "Failed to initialize panel: %d\n", ret); + gpiod_set_value_cansleep(ctx->reset_gpio, 1); + regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies); + return ret; + } + + ctx->prepared = true; + return 0; +} + +static int visionox_r66451_unprepare(struct drm_panel *panel) +{ + struct visionox_r66451 *ctx = to_visionox_r66451(panel); + struct device *dev = &ctx->dsi->dev; + int ret; + + if (!ctx->prepared) + return 0; + + ret = visionox_r66451_off(ctx); + if (ret < 0) + dev_err(dev, "Failed to un-initialize panel: %d\n", ret); + + gpiod_set_value_cansleep(ctx->reset_gpio, 1); + regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies); + + ctx->prepared = false; + return 0; +} + +static const struct drm_display_mode visionox_r66451_mode = { + .clock = (1080 + 95 + 1 + 40) * (2340 + 25 + 1 + 4) * 120 / 1000, + .hdisplay = 1080, + .hsync_start = 1080 + 95, + .hsync_end = 1080 + 95 + 1, + .htotal = 1080 + 95 + 1 + 40, + .vdisplay = 2340, + .vsync_start = 2340 + 25, + .vsync_end = 2340 + 25 + 1, + .vtotal = 2340 + 25 + 1 + 4, + .width_mm = 0, + .height_mm = 0,Please provide real values here.Acked.+}; + +static int visionox_r66451_enable(struct drm_panel *panel) +{ + struct visionox_r66451 *ctx = to_visionox_r66451(panel); + struct mipi_dsi_device *dsi = ctx->dsi; + struct drm_dsc_picture_parameter_set pps; + int ret; + + if (ctx->enabled) + return 0; + + if (!dsi->dsc) { + dev_err(&dsi->dev, "DSC not attached to DSI\n"); + return -ENODEV; + } + + drm_dsc_pps_payload_pack(&pps, dsi->dsc); + ret = mipi_dsi_picture_parameter_set(dsi, &pps); + + ctx->enabled = true; + + return 0; +} + +static int visionox_r66451_disable(struct drm_panel *panel) +{ + struct visionox_r66451 *ctx = to_visionox_r66451(panel); + + ctx->enabled = false; + + return 0; +} + +static int visionox_r66451_get_modes(struct drm_panel *panel, + struct drm_connector *connector) +{ + struct drm_display_mode *mode; + + mode = drm_mode_duplicate(connector->dev, &visionox_r66451_mode); + if (!mode) + return -ENOMEM; + + drm_mode_set_name(mode); + + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; + connector->display_info.width_mm = mode->width_mm; + connector->display_info.height_mm = mode->height_mm; + drm_mode_probed_add(connector, mode);Can we use drm_connector_helper_get_modes_fixed() instead?Acked.+ + return 1; +} + +static const struct drm_panel_funcs visionox_r66451_funcs = { + .prepare = visionox_r66451_prepare, + .unprepare = visionox_r66451_unprepare, + .get_modes = visionox_r66451_get_modes, + .enable = visionox_r66451_enable, + .disable = visionox_r66451_disable, +}; + +static int visionox_r66451_bl_update_status(struct backlight_device *bl) +{ + struct mipi_dsi_device *dsi = bl_get_data(bl); + u16 brightness = backlight_get_brightness(bl); + + return mipi_dsi_dcs_set_display_brightness(dsi, cpu_to_le16(brightness));mipi_dsi_dcs_set_display_brightness() already converts the brightness, so you don't need cpu_to_le16 here.Acked. Thanks, Jessica Zhang+} + +static const struct backlight_ops visionox_r66451_bl_ops = { + .update_status = visionox_r66451_bl_update_status, +}; + +static struct backlight_device * +visionox_r66451_create_backlight(struct mipi_dsi_device *dsi) +{ + struct device *dev = &dsi->dev; + const struct backlight_properties props = { + .type = BACKLIGHT_RAW, + .brightness = 255, + .max_brightness = 4095, + }; + + return devm_backlight_device_register(dev, dev_name(dev), dev, dsi, + &visionox_r66451_bl_ops, &props); +} + +static int visionox_r66451_probe(struct mipi_dsi_device *dsi) +{ + struct device *dev = &dsi->dev; + struct visionox_r66451 *ctx; + struct drm_dsc_config *dsc; + int ret = 0; + + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); + if (!ctx) + return -ENOMEM; + + dsc = devm_kzalloc(dev, sizeof(*dsc), GFP_KERNEL); + if (!dsc) + return -ENOMEM; + + /* Set DSC params */ + dsc->dsc_version_major = 0x1; + dsc->dsc_version_minor = 0x2; + + dsc->slice_height = 20; + dsc->slice_width = 540; + dsc->slice_count = 2; + dsc->bits_per_component = 8; + dsc->bits_per_pixel = 0x8 << 4; + dsc->block_pred_enable = true; + + dsi->dsc = dsc; + + ctx->supplies[0].supply = "vddio"; + ctx->supplies[1].supply = "vdd"; + + ret = devm_regulator_bulk_get(&dsi->dev, ARRAY_SIZE(ctx->supplies), + ctx->supplies); + + if (ret < 0) + return ret; + + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(ctx->reset_gpio)) + return dev_err_probe(dev, PTR_ERR(ctx->reset_gpio), "Failed to get reset-gpios\n"); + + ctx->dsi = dsi; + mipi_dsi_set_drvdata(dsi, ctx); + + dsi->lanes = 4; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = MIPI_DSI_MODE_LPM | MIPI_DSI_CLOCK_NON_CONTINUOUS; + + drm_panel_init(&ctx->panel, dev, &visionox_r66451_funcs, DRM_MODE_CONNECTOR_DSI); + ctx->panel.backlight = visionox_r66451_create_backlight(dsi); + if (IS_ERR(ctx->panel.backlight)) + return dev_err_probe(dev, PTR_ERR(ctx->panel.backlight), + "Failed to create backlight\n"); + + drm_panel_add(&ctx->panel); + + ret = mipi_dsi_attach(dsi); + if (ret < 0) { + dev_err(dev, "Failed to attach to DSI host: %d\n", ret); + drm_panel_remove(&ctx->panel); + } + + return ret; +} + +static void visionox_r66451_remove(struct mipi_dsi_device *dsi) +{ + struct visionox_r66451 *ctx = mipi_dsi_get_drvdata(dsi); + int ret; + + ret = mipi_dsi_detach(dsi); + if (ret < 0) + dev_err(&dsi->dev, "Failed to detach DSI host: %d\n", ret); + + drm_panel_remove(&ctx->panel); +} + +static const struct of_device_id visionox_r66451_of_match[] = { + {.compatible = "visionox,r66451"}, + { /*sentinel*/ } +}; +MODULE_DEVICE_TABLE(of, visionox_r66451_of_match); + +static struct mipi_dsi_driver visionox_r66451_driver = { + .probe = visionox_r66451_probe, + .remove = visionox_r66451_remove, + .driver = { + .name = "panel-visionox-r66451", + .of_match_table = visionox_r66451_of_match, + }, +}; + +module_mipi_dsi_driver(visionox_r66451_driver); + +MODULE_AUTHOR("Jessica Zhang <quic_jesszhan@xxxxxxxxxxx>"); +MODULE_DESCRIPTION("Panel driver for the Visionox R66451 AMOLED DSI panel"); +MODULE_LICENSE("GPL");-- With best wishes Dmitry-- With best wishes Dmitry
