On 29/04/2023 02:45, Kuogee Hsieh wrote:
During DSC preparation, add run time calculation to figure out what
usage modes, split mode and merge mode, is going to be setup.
This patch doesn't determine the mode. It changes programming of DSC
bits according to the mode being selected.
Signed-off-by: Kuogee Hsieh <quic_khsieh@xxxxxxxxxxx>
---
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 56 ++++++++++++++++-------------
1 file changed, 31 insertions(+), 25 deletions(-)
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
index 2fdacf1..3d18642 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
@@ -529,17 +529,9 @@ void dpu_encoder_helper_split_config(
bool dpu_encoder_use_dsc_merge(struct drm_encoder *drm_enc)
{
struct dpu_encoder_virt *dpu_enc = to_dpu_encoder_virt(drm_enc);
- int i, intf_count = 0, num_dsc = 0;
+ struct msm_display_topology *topology = &dpu_enc->topology;
- for (i = 0; i < MAX_PHYS_ENCODERS_PER_VIRTUAL; i++)
- if (dpu_enc->phys_encs[i])
- intf_count++;
-
- /* See dpu_encoder_get_topology, we only support 2:2:1 topology */
- if (dpu_enc->dsc)
- num_dsc = 2;
-
- return (num_dsc > 0) && (num_dsc > intf_count);
+ return (topology->num_dsc > topology->num_intf);
}
static void dpu_encoder_get_topology(
@@ -1861,41 +1853,55 @@ static void dpu_encoder_prep_dsc(struct dpu_encoder_virt *dpu_enc,
struct dpu_encoder_phys *enc_master = dpu_enc->cur_master;
struct dpu_hw_dsc *hw_dsc[MAX_CHANNELS_PER_ENC];
struct dpu_hw_pingpong *hw_pp[MAX_CHANNELS_PER_ENC];
- int this_frame_slices;
+ struct msm_display_topology *topology = &dpu_enc->topology;
int intf_ip_w, enc_ip_w;
- int dsc_common_mode;
- int pic_width;
+ int dsc_common_mode = 0;
Please don't top-init variables unless required (or unless they are
constant).
u32 initial_lines;
+ int num_dsc = topology->num_dsc;
+ int num_intf = topology->num_intf;
int i;
- for (i = 0; i < MAX_CHANNELS_PER_ENC; i++) {
+ for (i = 0; i < num_dsc; i++) {
hw_pp[i] = dpu_enc->hw_pp[i];
hw_dsc[i] = dpu_enc->hw_dsc[i];
if (!hw_pp[i] || !hw_dsc[i]) {
DPU_ERROR_ENC(dpu_enc, "invalid params for DSC\n");
return;
- }
+ }
What is the difference here?
}
- dsc_common_mode = 0;
- pic_width = dsc->pic_width;
+ intf_ip_w = dsc->pic_width;
- dsc_common_mode = DSC_MODE_MULTIPLEX | DSC_MODE_SPLIT_PANEL;
if (enc_master->intf_mode == INTF_MODE_VIDEO)
dsc_common_mode |= DSC_MODE_VIDEO;
- this_frame_slices = pic_width / dsc->slice_width;
- intf_ip_w = this_frame_slices * dsc->slice_width;
-
/*
- * dsc merge case: when using 2 encoders for the same stream,
- * no. of slices need to be same on both the encoders.
+ * If this encoder is driving more than one DSC encoder, they
+ * operate in tandem, same pic dimension needs to be used by
+ * each of them.(pp-split is assumed to be not supported)
+ *
Extra empty line. Also the comment doesn't make sense here anymore. We
already have comment for the division by two below.
*/
- enc_ip_w = intf_ip_w / 2;
+ enc_ip_w = intf_ip_w;
+
+ intf_ip_w /= num_intf;
+
+ if (num_dsc > 1)
+ dsc_common_mode |= DSC_MODE_SPLIT_PANEL;
+
+ if (dpu_encoder_use_dsc_merge(&dpu_enc->base)) {
+ dsc_common_mode |= DSC_MODE_MULTIPLEX;
+ /*
+ * in dsc merge case: when using 2 encoders for the same
+ * stream, no. of slices need to be same on both the
+ * encoders.
+ */
+ enc_ip_w = intf_ip_w / 2;
+ }
+
initial_lines = dpu_encoder_dsc_initial_line_calc(dsc, enc_ip_w);
- for (i = 0; i < MAX_CHANNELS_PER_ENC; i++)
+ for (i = 0; i < num_dsc; i++)
dpu_encoder_dsc_pipe_cfg(dpu_enc, hw_dsc[i], hw_pp[i], dsc,
dsc_common_mode, initial_lines);
}
--
With best wishes
Dmitry
